Page 194 of 333
193
Driving
Before Driving Driving Preparation
Do not place anything in the seat footwells. Make sure to secure the floor mats.
•
An object or unsecured floor mat can interfere with your brake and
accelerator pedal operation while driving.
If you have any animals on board, do not let them move around in the vehicle.
•
They may interfere with driving and a crash could occur.
Securely close and lock both doors and the hatch.
•
Locking and Unlocking the Doors from Inside P.102
Adjust your seating position properly.
•
Adjusting the Seats P.119
Adjust the mirrors and steering wheel properly for your driving.
•
Adjust them while sitting in the proper driving position.
Adjusting the Mirrors P.118
Steering Wheel Adjustments P.117
Be sure items placed on the floor behind the driver’s and passenger’s seats
•
cannot roll under the seats.
They can interfere with the driver’s ability to operate the pedals, the operation
of the seats, or the operation of the sensors under the seats.
Everyone in the vehicle must fasten their seat belt.
•
Fastening a Seat Belt P.37
Make sure that the indicators in the instrument panel come on when you start
•
the vehicle, and go off soon after.
Always have a dealer check the vehicle if any of the indicators indicate a
problem.
Indicators P.68
Main MenuTable of Contents
Page 247 of 333
246
Maintenance
Maintenance Under the Hood Opening the Hood
Opening the Hood1. Park the vehicle on a level surface, and set the parking brake.Pull the hood release handle under the
2.
lower left corner of the dashboard.
The hood will pop up slightly.
3. Push up the hood latch lever in the center
of the hood to release the lock mechanism, and open the hood.
4. Remove the support rod from the clamp using the grip. Mount the support rod in the hood.
When closing, remove the support rod, and stow it in the clamp, then gently lower the hood. Remove your hand at a height of approximately 12 inches (30 cm) and let the hood close.
Hood Release Handle
Pull
Opening the Hood
NOTICE Do not open the hood when the wiper arms are raised.The hood will strike the wipers, and may damage either the hood or the wipers. When closing the hood, check that the hood is securely locked. If the hood latch lever moves stifly, or if you can open the hood without lifting the lever, the mechanism should be cleaned and lubricated. Do not open the hood while the auto idle stop function is activated.
Lever
Support Rod
Grip
Clamp
Main MenuTable of Contents
Page 250 of 333
249
Maintenance
Maintenance Under the Hood Adding Engine Oil
Adding Engine Oil1. Unscrew and remove the engine oil fill cap. Slowly pour in the oil.
2.
Reinstall the engine oil fill cap, and tighten
3.
it securely.Wait for several minutes and recheck the
4.
engine oil dipstick.
Engine Oil Fill Cap
Adding Engine Oil
If any oil spills, wipe it up immediately. Spilled oil may damage the engine compartment components.
NOTICE Do not ill the engine oil above the upper limit
mark. Overilling the engine oil may result in engin e
damage.
Main MenuTable of Contents
Page 255 of 333
254
Maintenance
Maintenance Under the Hood Transmission Fluid
Transmission Fluid
Automatic Transmission Fluid
■
Continuously Variable Transmission (CVT)
■
Specified fluid: Honda CVTF (continuously variable transmission fluid)
Check the fluid level when the engine is at normal operating temperature. 1. Park on level ground, and start the engine. Wait until the radiator fan starts and then
2.
turn off the engine.
Perform step 3 after waiting for about 60 seconds (less than 90 seconds).
Remove the dipstick (yellow loop) from the
3.
transmission and wipe it with a clean cloth. Insert the dipstick all the way back into
4.
the transmission securely, as shown in the image. Remove the dipstick again and check the
5.
fluid level.
It should be between the upper and lower marks in the HOT range.
If the level is below the lower mark, add
6.
fluid into the dipstick hole to bring it to the level between the upper and lower marks, and have your vehicle checked by a dealer immediately.
Pour the fluid slowly and carefully
so you do not spill any. Clean up any spills immediately; they can damage components in the engine compartment.
Upper Mark Lower Mark
HOT Range
Main MenuTable of Contents
Page 279 of 333
278
Maintenance
12 Volt Battery
Checking the 12 Volt Battery
Check the battery condition monthly. Look at the test indicator window and check the terminals for corrosion.
If your vehicle’s battery is disconnected or goes dead: The audio system is disabled.
•
Entering the Security Code P.140
The clock resets.
•
Setting the Clock P.98
The navigation system is disabled. A PIN code will be required.
•
Refer to the navigation system manual.
Charging the 12 Volt Battery Disconnect both battery cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative (–) cable first, and reconnect it last.
Test Indicator Window 12 Volt Battery
WARNING: Battery posts, terminals, and
related accessories contain lead and lead compounds.Wash your hands after handling. The test indicator's color information is on the battery. When you ind corrosion, clean the battery terminals by applying a baking powder and water solution. Rinse the terminals with water. Cloth/towel dry the battery. Coat the terminals with grease to help prevent future corrosion. If the 12 volt battery is disconnected or goes dead, the IMA battery level gauge reading may show less than the actual level the next time you turn the ignition switch to ON
. It will show the correct
level after you drive for about 30 minutes.
WARNING
The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. Wear protective clothing and a face shield, or have a skilled technician do any battery maintenance.
Main MenuTable of Contents
Page 283 of 333
282
Maintenance
Cleaning Interior Care
Floor Mats
■
The driver’s floor mat hooks over the floor anchors, which keep the mat from sliding forward. To remove the mat for cleaning, turn each anchor knob to the unlock position. When reinstalling the mat after cleaning, turn each knob to the lock position. Do not put additional floor mats on top of the anchored mat.
Maintaining Genuine Leather
■*
Vacuum dirt and dust from the leather frequently. Pay close attention to the pleats and seams. Clean the leather with a soft cloth dampened with a 90% water and 10% neutral wool detergent solution. Then buff it with a clean, dry cloth. Remove any dust or dirt on leather surfaces immediately.
Floor Mats
If you use any loor mats that were not originally provided with your vehicle, make sure they are designed for your speciic vehicle, it correctly and are securely anchored by the loor anchors.
Driver’s loor mat is shown.
Unlock
Lock
* Not available on all models
Main MenuTable of Contents
Page 293 of 333
292
Handling the Unexpected
If a Tire Goes Flat Changing a Flat Tire
Storing the Flat Tire
■
1. Remove the center cap and place the flat tire face down in the spare tire well.Remove the spacer cone from the wing
2.
bolt, flip it over, and insert it back on the bolt. Secure the flat tire with the wing bolt. Securely put the jack and wheel nut
3.
wrench back in the tool case in the cargo area.
TPMS and the Spare Tire
■
U.S. models only
If you replace a flat tire with the spare tire, the low tire pressure/TPMS indicator comes on while you are driving. After driving for a few miles (kilometers), the indicator will start blinking for a short time and then stay on. “CHECK TPMS SYSTEM” appears on the multi-information display, but this is normal. If you replace the tire with a specified regular tire, the warning message on the multi-information display and the low tire pressure/TPMS indicator will go off after a few miles (kilometers).
Storing the Flat Tire
WARNING
Loose items can fly around the interior in a crash and can seriously injure the occupants. Store the wheel, jack, and tools securely before driving.
Spacer Cone
Wing Bolt
For compact spare tire
For normal tire
TPMS and the Spare Tire
The system cannot monitor the pressure of the
spare tire. Manually check the spare tire pressure to
be sure that it is correct. Use TPMS speciic wheels. Each is equipped with a tire pressure sensor mounted inside the tire behind the valve stem.
Main MenuTable of Contents
Page 295 of 333
294
Handling the Unexpected
Jump Starting
Jump Starting Procedure
■
Turn off the power to electric devices, such as audio and lights. Turn off the engine, then open the hood.
1. Connect the first jumper cable to your vehicle’s battery
terminal.
Connect the other end of the first jumper
2.
cable to the assisting vehicle’s
terminal.
Use a 12 volt booster battery only.
Connect the second jumper cable to the
3.
assisting vehicle’s
terminal.
4. Connect the other end of the second jumper cable to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine. If your vehicle is connected to another
5.
vehicle, start the assisting vehicle’s engine and increase its rpm slightly. Attempt to start your vehicle’s engine. If
6.
it turns over slowly, check that the jumper cables have good metal-to-metal contact.
Jump Starting
Securely attach the jumper cables clips so that they do not come off when the engine vibrates. Also be careful not to tangle the jumper cables or allow the cable ends to touch each other while attaching or detaching the jumper cables. Battery performance degrades in cold conditions and may prevent the engine from starting.
WARNING
A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Keep all sparks, open flames, and smoking materials away from the battery.
Assisting
Vehicle’s Battery
Main MenuTable of Contents
