2011 HONDA CR-Z brake light

229
Driving
Parking Your Vehicle Auto Idle Stop (Manual Transmission)
The Engine Automatically Restarts When:
■
The clutch pedal is fully depressed, and the shift lever is moved to a position other than
N.
The Engine Automatically Restarts When the Clutch Pedal is Fully
■
Depressed Even If the Shift Lever is in
N When:
The low temperature indicator comes on.

•
The accelerator pedal is pressed.

•
The IMA battery charge becomes low.

•
The climate control system is in use, and the difference between the set

•
temperature and actual interior temperature becomes significant. The climate control system is being used to dehumidify the interior.

• The engine automatically restarts when the pressure on the brake pedal is repeatedly applied and released slightly during a stop. This applies even if the clutch pedal is not fully depressed.
When the Auto Idle Stop Indicator Starts Blinking Rapidly

■
Fully depress the clutch pedal.
The engine automatically restarts
When the Auto Idle Stop Indicator Starts Blinking
Rapidly
The indicator starts blinking rapidly under the following conditions: The

•
(windshield defogger) button is pressed.
When the climate control system is in use and

•
moisture builds up inside the vehicle. When the climate control system is in use and

•
the difference between the set temperature and the actual temperature inside the vehicle becomes signiicant.
Main MenuTable of Contents

Maintenance
This chapter discusses basic maintenance.
237
Before Performing Maintenance
Inspection and Maintenance ................... 238
Safety When Performing Maintenance ... 239Parts and Fluids Used in Maintenance
Service .................................................. 240
Maintenance Minder ™
............................ 241
Maintenance Under the Hood Maintenance Items Under the Hood ....... 245
Opening the Hood ................................. 246
Recommended Engine Oil ...................... 247
Oil Check ............................................... 248
Adding Engine Oil .................................. 249
Changing the Engine Oil and Oil Filter .... 250 Engine Coolant ...................................... 252
Transmission Fluid .................................. 254
Brake/Clutch Fluid .................................. 256
Refilling Window Washer Fluid ............... 257
Replacing Light Bulbs ............................. 258
Checking and Maintaining Wiper Blades Checking Wiper Blades ........................... 266
Changing the Front Wiper Blade Rubber 266
Changing the Rear Wiper Blade Rubber .. 268
Checking and Maintaining Tires Checking Tires ........................................ 269
Tire and Loading Information Label ........ 270
Tire Labeling ........................................... 270 DOT Tire Quality Grading (U.S. Vehicles)
.272
Wear Indicators ...................................... 274
Tire Service Life ...................................... 274
Tire and Wheel Replacement .................. 275
Tire Rotation .......................................... 276
Winter Tires ............................................ 277
12 Volt Battery ........................................ 278
Remote Transmitter Care ....................... 279
Replacing the Battery ............................. 279
Climate Control System Maintenance ... 280
Cleaning ................................................... 281
Interior Care ........................................... 281
Exterior Care .......................................... 283
Main Menu

238
Maintenance
Before Performing Maintenance
Inspection and Maintenance
For your safety, perform all listed inspections and maintenance to keep your vehicle
in good condition. If you become aware of any abnormality (noise, smell, insufficient brake fluid, oil residue on the ground, etc.), have your vehicle inspected by a dealer. (Note, however, that service at a dealer is not mandatory to keep your warranties in effect.) Refer to the separate maintenance booklet for detailed maintenance and inspection information.Types of Inspection and Maintenance

■
Daily Inspections
■
Perform inspections before long distance trips, when washing the vehicle, or when refueling.
Periodic Inspections
■
Check the automatic transmission fluid level monthly.
•
Automatic Transmission Fluid P.254
Check the brake fluid level monthly.
•
Brake/Clutch Fluid P.256
Check the tire pressure monthly. Examine the tread for wear and foreign objects.
•
Checking and Maintaining Tires P.269
Check the operation of the headlights, parking lights, taillights, high-mount
•
brake light, and license plate lights monthly.
Replacing Light Bulbs P.258
Check the condition of the wiper blades at least every six months.
•
Checking and Maintaining Wiper Blades P.266
Inspection and Maintenance
U.S. models only Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are "certiied" to EPA standards. According to state and federal regulations, failure to perform maintenance on the items marked with # will not void your emissions warranties. However, all maintenance services should be performed in accordance with the intervals indicated by the multi-information display.
Maintenance Service Items P. 2 4 3
If you want to perform complex maintenance tasks that require more skills and tools, purchase the service manual.
Authorized Manuals P. 3 1 9
If you want to perform maintenance yourself, make sure that you have the necessary tools and skills irst.After performing maintenance, complete the records in the separate maintenance booklet.
Main MenuTable of Contents

245
Maintenance
Maintenance Under the Hood
Maintenance Items Under the Hood
Brake Fluid (Black cap)
Washer Fluid (Blue cap)
Engine Coolant Reservoir
Engine Oil Fill Cap
Manual
Transmission model:Clutch Fluid(Light Gray cap)
Automatic Transmission (CVT) Fluid Dipstick
(Yellow loop)
Radiator Cap
Engine Oil Dipstick (Orange handle)
Main MenuTable of Contents

246
Maintenance
Maintenance Under the Hood Opening the Hood
Opening the Hood1. Park the vehicle on a level surface, and set the parking brake.Pull the hood release handle under the
2.
lower left corner of the dashboard.
The hood will pop up slightly.
3. Push up the hood latch lever in the center
of the hood to release the lock mechanism, and open the hood.
4. Remove the support rod from the clamp using the grip. Mount the support rod in the hood.
When closing, remove the support rod, and stow it in the clamp, then gently lower the hood. Remove your hand at a height of approximately 12 inches (30 cm) and let the hood close.
Hood Release Handle
Pull
Opening the Hood
NOTICE Do not open the hood when the wiper arms are raised.The hood will strike the wipers, and may damage either the hood or the wipers. When closing the hood, check that the hood is securely locked. If the hood latch lever moves stifly, or if you can open the hood without lifting the lever, the mechanism should be cleaned and lubricated. Do not open the hood while the auto idle stop function is activated.
Lever
Support Rod
Grip
Clamp
Main MenuTable of Contents

258
Maintenance
Replacing Light Bulbs
Headlight Bulbs
When replacing, use the following bulbs.
High beam headlight: 60W (HB3)
Low beam headlight: 55W (H11 for halogen bulb type)
35W (D4S for high voltage discharge)High Beam Headlight

■
1. Remove the cover.
2. Remove the coupler.
It can be removed by pushing the tab.
Rotate the old bulb to the left to remove.
3.
Insert a new bulb into the headlight
4.
assembly and turn it to the right.
Insert the coupler into the connector of the
5.
bulb.
Headlight Bulbs
NOTICE Halogen bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.
NOTICE The headlight aim is set by the factory, and typically does not need to be adjusted. However, if you regularly carry heavy items in the cargo area, have the aiming readjusted by a dealer or another qualiied technician. The HB3 and H11 types are halogen bulbs. When replacing a bulb, handle it by its base, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth. The exterior lights’ inside lenses (headlights, brake lights, etc.) may fog temporarily after a vehicle wash or while driving in the rain. This does not impact the exterior light function.However, if you see a large amount of water or ice accumulated inside the lenses, have your vehicle inspected by a dealer.
Cover
Bulb
TabCoupler
Main MenuTable of Contents

264
Maintenance
Replacing Light Bulbs Back-Up, Rear Turn Signal and Rear Side Marker Light Bulbs Brake/Taillight Bulbs
4. Turn the socket to the left and remove it, then remove the old bulb.Insert a new bulb.
5. 6. Reinstall the light assembly by sliding it on to the guide on the body.
Brake/Taillight Bulbs
Brake/rear taillight bulbs are LED type. Have an au thorized Honda dealer inspect and
replace the light bulbs.
Guide
Main MenuTable of Contents

265
Maintenance
Replacing Light Bulbs License Plate Light Bulbs High-Mount Brake Light Bulbs
License Plate Light Bulbs
When replacing, use the following bulbs.
License Plate Light: 5W1. Remove the lens by prying on the edge of the lens using a flat-tip screwdriver.
Wrap the flat-tip screwdriver with a
cloth to prevent scratches.
2. Remove the old bulb. Insert a new bulb.
3.
High-Mount Brake Light Bulbs High-mount brake light bulbs are LED type. Have an authorized Honda dealer inspect and replace the light bulbs.
Main MenuTable of Contents