2011 HONDA CR-Z diagnostic menu

Quick Reference Guide
26
California Proposition 65 Warning
WARNING: This product contains or emits chemicals
known to the state of California to cause cancer and birth
defects or other reproductive harm.
Event Data Recorders
This vehicle is equipped with one or more devices
commonly referred to as event data recorders. These
devices record front seat belt use, front passenger
seat occupancy, airbag deployment data, and the
failure of any airbag system component. This data
belongs to the vehicle owner and may not be accessed
by anyone else except as legally required or with the
permission of the vehicle owner.
Service Diagnostic Recorders
This vehicle is equipped with service-related devices that
record information about powertrain performance. The
data can be used to verify emissions law requirements and/or help technicians diagnose and solve service
problems. It may also be combined with data from other
sources for research purposes, but it remains conidential.
California Perchlorate Contamination Prevention Act
The airbags, seat belt tensioners, and CR type batteries
in this vehicle may contain perchlorate materials - special
handling may apply. See www.dtsc.ca.gov/hazardouswaste/
perchlorate/ As you read this manual, you will find information that is
preceded by a
symbol. This information is intended to
help you avoid damage to your vehicle, other property, or the
environment.
Main Menu

69
Instrument Panel
Indicators
IndicatorName On/Blinking Explanation Message
Malfunction Indicator Lamp Comes on when you turn the

•
ignition switch to ON
II, and goes
off either when the engine starts or after several seconds if the engine is not started. If “readiness codes” have not been set, it blinks five times before it goes off.Comes on if there is a problem

•
with the emissions control system.Blinks when a misfire in the

•
engine’s cylinders is detected. Readiness codes are part of the on

•
board diagnostics for the emissions control systems.
Readiness Codes P.317
Comes on during driving

• - Have
the vehicle checked by a dealer immediately.Blinks during driving

• - Stop in a safe
place where there are no flammable objects. Stop the engine for 10 minutes or more, and wait for it to cool down. Then, take the vehicle to a dealer.
If the Malfunction Indicator Lamp Comes On or Blinking P.301
12 Volt Battery Charging System Indicator Comes on when you turn the

•
ignition switch to ON
II, and goes
off when the engine starts.
Comes on when the 12 volt battery

•
is not charging. Comes on during driving

• - Turn off
the climate control system and rear defogger in order to reduce electricity consumption.
If the 12 Volt Battery Charging System Indicator Comes On P.300
Transmission Indicator(Shift Position Indicator) * Comes on for a few seconds when

•
you turn the ignition switch to ON
II, then goes off.
Blinks if the transmission system

•
has a problem. Blinks during driving

• - Avoid
sudden starts and acceleration and have the vehicle checked by a dealer immediately.
* Not available on all models
Main MenuTable of Contents

317
Information
Emissions Testing
Testing of Readiness Codes
Testing of Readiness Codes
The readiness codes are erased when the 12 volt battery is disconnected, and set again only after several days of driving under a variety of conditions. If a testing facility determines that the readiness codes are not set, you may be requested to return at a later date to complete the test.
If the testing facility determines the readiness co des
are still not set, see a dealer.
Your vehicle uses “readiness codes,” as part of it’s onboard self diagnostic system. Some States refer to these codes during testing to see if your vehicle’s emissions components are working properly. The codes may not be read if you go through the testing just after the battery has gone dead or been disconnected. To check if they are set, turn the ignition switch to ON
II, without starting the
engine. The malfunction indicator lamp will come on for several seconds. If it then goes off, the readiness codes are set. If it blinks five times, the readiness codes are not set. If you are required to have your vehicle tested before the readiness codes are ready, prepare the vehicle for retesting by doing the following:
Fill the gas tank to approximately 3/4 full.
1.
Park the vehicle and leave the engine off for 6 hours or more.
2.
Make sure the ambient temperature is between 40 °F and 95 °F (4 °C and 35
3.
°C).Start the engine without touching the accelerator pedal, and let it idle for 20
4.
seconds.Keep the vehicle in
5.
P (automatic transmission) or N (manual transmission).
Increase the engine speed to 2,000 rpm, and hold it there for about 3 minutes. Let the engine idle with your foot off the accelerator for 20 seconds.
6.
continued
Main MenuTable of Contents