2010 SKODA OCTAVIA TOUR technical data

Unlocking and locking33
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Unlocking and lockingKeyTwo keys are provided with the vehicle. Depending on the equipment, your vehicle
can be equipped with keys without radio remote control fig. 27 or with radio
remote control* fig. 28 .
Key ring
A plastic tag fig. 27 is attached to one of the keys wi th the identification of the key.
This identification ca n be used to order replacement keys from specialist garages. Carefully
store the key ring on which there is the number, because a replacement key
can only be ordered with this number in case the key is lost or damaged. You should
also therefore hand over this key ring to the purchaser when selling the vehicle.
WARNING

Always withdraw the key wh enever you leave the vehicle - even if it is only
for a short time. This is particularly important if children are left in the vehicle.
The children might otherwise start the en gine or operate electrical equipment
(e.g. power windows) - risk of injury!

Do not withdraw the ignition key from the ignition lock until the vehicle has
come to a stop. The steering lock might otherwise engage unintentionally - risk
of accident!Caution

Each key contains electronic components; therefore protect them against mois-
ture and severe shocks.

Keep the groove of the keys absolutely clean as impurities (textile fibres, dust etc.)
have a negative effect on the proper operation of the locking cylinder and the ignition
lock.Note
Please approach a specialist garage if you lose a key since he can obtain a new one for
you.
Fig. 27 Set of keys without
remote controlFig. 28 Remote control key
s2rc.book Page 33 Thursd ay, April 22, 2010 10:58 AM

Unlocking and locking35
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Locking from outside
The securing knob will move upwards or downwards in the door when
unlocking or
locking.
Locking from inside
All closed vehicle doors are locked by pressi ng in the securing knobs from the inside.
The doors cannot be opened from the outs ide when the securing knobs have been
pressed in. The vehicle doors can be opened from the inside as follows:

the door is unlocked by actu ating the door-opening lever;

The door opens upon actuating the door-opening lever again.Note

The opened door cannot be locked with the securing knob. This prevents the
possibility of forgetting the key in the locked vehicle.

The opened side doors at the rear and the front passenger door are locked by
pressing in the securing knob and slamming the door closed.

Please refer to the safety guidelines page 35.
Child safety lockThe child safety lock prevents the re ar door from being opened from the
inside.
The rear doors are equipped with a child safe ty lock. You can switch the child safety
lock on and off using the vehicle key.Switching child safety lock on– Use the vehicle key to turn the slit in the rear door to the left in the direction of the arrow fig. 31 .Switching child safety lock off– Use the vehicle key to turn the slit to the right against the direction of the arrow.
So long as the child safety lock is switched on it is not possible to open the door from
the inside with the door opening lever. In this case the door can be opened only from
the outside.Central locking system*DescriptionUnlocking or locking the vehicle causes all doors to be unlocked or locked at the same
time by the central locking system. The boot lid is unlocked when opening. It can be
opened by pressing the hand grip above the licence plate page 38, fig. 34 .
Operation of the central locking system is possible:
from the outside using the vehicle key page 37,

using the button for the central locking system page 37,

by using the remote control page 39.

with the securing knobs in the doors page 37, fig. 33 - only for vehicles which
are not fitted with electrically operated power windows (only for locking).
Warning light and securing knobs in the doors
All the securing knobs move upwards when unlocking.
The driver door must be closed when locking. Other doors can also be closed after
locking.
Fig. 31 Child safety locks on the
rear doors
s2rc.book Page 35 Thursd ay, April 22, 2010 10:58 AM

Unlocking and locking37
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Unlocking the vehicle using the key– Turn the key in the locking cylinder of th e driver's door to the left in the unlock
position fig. 32 .
– Pull on the door handle and open the door.
All the doors are unlocked.

The boot lid is then unlocked.

The switched on interior lights come on over the door contact.

The safe securing system is deactivated.

The windows open provided the key is held* in the unlock posi tion. On vehicles
fitted with anti-theft alarm system the wi ndow operation is only possible 45 seconds
after deactivation of the warning system.

The indicator light in the driver's door stop s flashing if the vehicle is not fitted with
an anti-theft alarm system* page 40.Note
If the vehicle is equippe d with an anti-theft alarm system*, you must insert the key into
the ignition lock and switch the ignition on within 15 seconds after unlocking the door
in order to deactivate the anti-theft alarm system. The alarm will be triggered if you
do not switch on the ignition within 15 seconds.
Locking the vehicle with the key– Turn the key in the locking cylinder of the driver's door to the right in the lock posi-
tion fig. 32 .
All the doors and the boot lid are locked.

The switched on interior lights will switch off over the door contact.

The windows and the electric sliding/ti lting roof* close provided the key is held in
the lock position.

The safe securing system is activated immediately.

The indicator light in the dr iver door begins flashing.Note
The opened driver door cannot be locked. It must be locked separately after closing
it.Button for the central locking systemIf the vehicle is not locked from outside, you can unlock an d lock the vehicle with the
button in the driver door.Locking all doors and the boot lid– Press button fig. 33 . The symbol
 in the button comes on.
Fig. 32 Turning the key for
unlocking and locking the
vehicle
AA
AB
Fig. 33 Button for the central
locking system
A1
s2rc.book Page 37 Thursd ay, April 22, 2010 10:58 AM

Unlocking and locking39
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Remote control*DescriptionThe vehicle can be unlocked and lock ed using the radio remote control.
The transmitter with the battery is incorporat ed in the handle of the master key. The
receiver is located in the interior of the car. The operating range of the remote control
key is approx. 10 m. But this range can be reduced if the batteries are weak.
The master key has a fold-open key bit which can be used for unlocking and locking
the car manually and also for starting the engine.
If a lost key is replaced or if the receiver unit has been repaired or a new unit installed,
it is then necessary for a specialist garage to adapt the system. Only after this is it
possible to again use the remote control.
Note

The remote control is automatically deactivated when the ignition is switched on.

The operation of the remote control may temporarily be affected by interference
from transmitters close to th e car and which operate in the same frequency range (e.g.
mobile phone, TV transmitter).

The battery must be replaced, ideally by a specialist garage, if the central locking or
anti-theft alarm system does react to the remote control at less than 3 metres away.
Unlocking and locking car
Unlocking the vehicle

– Press button for about 1 second.Locking the vehicle

– Press button for about 1 second.Deactivating safe securing system– Press button twice in 2 seconds. Further information page 36.Folding out of the key– Press button .Folding up of the key– Press button and collapse the key bit in the housing.
The turn signal lights flash twice as confir mation that the vehicle has been unlocked.
The vehicle will lock again automatically if you unlock the vehicle using button but
do not open a door or the boot lid within th e next 30 seconds. This function is intended
to prevent the car being unlocked unintentionally.
The safe securing system along with the anti-theft alarm system are, however, deacti-
vated during these 30 seconds.
In addition, when the car is unlocked, the electrically adjustable seats and exterior
mirrors* move into the position assigned to this key. The stored setting of driver seat
and exterior mirrors is retrieved.
The turn signal lights flash once to confir m that the vehicle has been correctly locked.
If the turn signal lights do not flash, ch eck the doors, bonnet and boot lid again to
ensure that they are closed. If the doors, the bonnet or the boot lid remain open when
the anti-theft alarm system is activated, the turn signal lights do not flash until after
they have been closed.
When the vehicle is unlocked or locked, the interior lights in the door contact are auto-
matically switched on or off.
Fig. 35 Folding key with radio
remote control
A1A2A2A3A3
A1
s2rc.book Page 39 Thursd ay, April 22, 2010 10:58 AM

Unlocking and locking41
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
This function makes it possible for example to leave animals in the vehicle.
How is the alarm switched off?
You switch the alarm off if you unlock the vehicle with the radio remote control or if
you switch the ignition on.
Note

The working life of the alarm siren is 5 years. More detailed information is available
by a specialist garage.

Before leaving the car, check that all the doors, windows and the electric
sliding/tilting roof* are properly closed in order to ensure that the anti-theft alarm
system is fully operational.

Coding of the radio remote control and th e receiver unit precludes the use of the
radio remote control from other vehicles.
Power windows*Buttons on the driver's doorThe power windows operate only when igniti on is switched on. After switching the
ignition off, the power windows can sti ll be operated however for maximum 10
minutes if a front door is not opened.
Opening a window– A window is opened by pressing lightly on the respective button in the door. The process stops when one releases the button.
– Additionally you can open the window automatically (fully open ed) by pressing the
button up to the stop. Renewed pressing of the button causes the window to stop
immediately.Closing a window– A window is closed through pulling lightly on the respective button in the door. The
closing process stops when one releases the button.
– Additionally you can close the window automatically (fully closed) by pulling the button up to the stop. Renewed pulling of the button causes the window to stop
immediately.
The buttons for the individual windows are lo cated in the armrest of the driver's door
 fig. 36 , front passenger door and in the rear doors*.
Buttons for the power windows in the armrest for the driver Button for the power window in the driver's door
Button for the power window in the front passenger's door
Button for the power window in the rear door on the right*
Button for the power window in the rear door on the left*
Safety pushbutton*
Safety pushbutton*
You can deactivate the buttons for power wind ows at rear doors by pressing the safety
pushbutton fig. 36 . The buttons for power windows at rear doors are activated
again by pressing the safety pushbutton again.
If the buttons for the rear doors are deactivated, the indicator light
 in the safety
switch lights up.
Fig. 36 Buttons on the driver's
door
AAABACADAS
AS
AS
AS
s2rc.book Page 41 Thursd ay, April 22, 2010 10:58 AM

Unlocking and locking43
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Window convenience operationYou can open and close the electrically po wered windows as follows when unlocking
and locking the vehicle (only close the sliding/tilting roof):Opening a window– Hold the key in the locking cylinder of the driver's door in the unlock position until
all the windows are opened.Closing a window– Hold the key in the locking cylinder of the dr iver's door in the lock position until all
the windows are closed.
You can interrupt the opening or closing operation of the windows immediately by
releasing the key.
WARNING

There must not be any persons in th e vehicle which is locked from the
outside. After approx. 10 minutes have expired or after opening and closing the
vehicle door when the ignition is switched off, the windows can no longer be
opened.

The person who operates the convenie nce system must take extra care,
when closing the window, that no passengers suffer any injuries.Note
Obstruction protection is not active during the convenience operating feature.Operational faultsElectrically operated power windows do not operate
If the battery of the car has been disconne cted and then reconnected, the electrically
operated power windows do not operate. The system must be activated. Proceed as
follows in order to re-establish the function:

Hold the key in the locking cylinder of the driver's door in the lock position until all
the windows are closed,

Release the key,

Hold the key again in the lockin g position for about 3 seconds.
Operation in winter
Ice accumulating on the surface of the wi ndows during the winter may result in a
greater resistance when closing the windows and the window may stop and go down
several centimetres
Proceed as follows to close the window fully:

Hold the key in the locking cylinder of the driver's door in the lock position until all
the windows are closed,

Repeat this operatiive cy cle when the window stops.
WARNING
The system is fitted with a force limiter page 42. If there is an obstacle, the
closing process is stopped and the window goes down by several centimeters.
You should then take particular care when closing the windows! You may
otherwise suffer severe injuries as a re sult of getting an arm, for example,
jammed in the window!
s2rc.book Page 43 Thursd ay, April 22, 2010 10:58 AM

Unlocking and locking45
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Convenience operationYou can also close an open sliding/tilting roof from the outside.
– Hold the key in the locking cylinder of the driver's door in the lock position until the
sliding/tilting roof is closed .
The closing process stops when one releases the key.
WARNING
Close the sliding/tilting roof carefully - ri sk of injury! The force limiter does not
operate with the convenience closing.Emergency operation
You can close and/or open the sliding/tiltin g roof by hand if the system is defect.
– Position the flat blade of a screwdriver carefully against the rear edge of the cover of the electrical drive.
–Pull the cover down fig. 38 .
– Insert an Allen key, Group 4, up to the stop into the opening and close and/or open the sliding/tilting roof.
– Press on the cover again by first of all inserting the plastic lugs and then pushing
the cover up.
– Have the malfunction rectified by a specialist garage.
Note
It is necessary after each emergency op eration (using Allen key) to move the
sliding/tilting roof into the basic position . Here you have to turn the control dial
forward to the switch position page 44, fig. 37 and press for about 10 seconds.
Fig. 38 Detail of the headliner:
point for positioning screwdriverFig. 39 Detail of the headliner:
Emergency operation
AA
s2rc.book Page 45 Thursd ay, April 22, 2010 10:58 AM

Lights and Visibility47
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data

The temperature difference between interior and external area of the headlight
lenses is decisive.
 When the driving lights are switched on, the light outlet surfaces are free from
mist after a short period. The headlight le nses can possibly mist up at the border
areas.
 It also concerns reverse light and turn signal lights.
 This mist has no influence on th e life of the lighting system.
Fog lights*

Switching on the fog lights– First of all turn the light switch into position
 or   fig. 41 .
– Pull the light switch into position .
If the fog lights are switched on, the symbol
 next to the light switch is more brightly
illuminated as well as the warning light in the instrument cluster page 27.
Rear fog light

Switching on the rear fog light– First of all turn the light switch into position
 or   fig. 41 .
– Pull the switch into position . If the vehicle is not fitted with fog lights*, th
e rear fog light is switched on by turning the
light switch to the position
 and is pulled out directly to the position . This switch
does not have two positions, but only one position.
The warning light
 lights up in the instrument cluster when the rear fog light is
switched on page 25.
Only the rear fog light of the trailer lights up automatically when you are towing a
trailer using a factory-fitted towing device which is fitted with the rear fog light.
The rear fog light is located in the rear light array on the driver's side.
Caution
The rear fog light should only be switched on if visibility is particularly poor (conform
with any varying legal provisions) to avoi d dazzling vehicles behind your vehicle.Instrument lighting*

You can adjust the brightness of the instrument lighting.Instrument lighting– Switch on the light.
– Turn the control dial fig. 42 to the desired intensity of the instrument lighting.
Fig. 41 Dash panel: Light switch
A1
A2
A2
Fig. 42 Dash panel: Instrument
lighting
s2rc.book Page 47 Thursd ay, April 22, 2010 10:58 AM