2010 Seat Leon 5D MEDIA SYSTEM 2.2

Navigation
64changed while route guidance is in progress. The route will then be recalcu-
lated.•Press the unit button in one of the navigation menus.•In the Navigation setup menu , press the function button
⇒ page 63, fig. 63.•Select or deselect an option by ticking or clearing the appropriate
checkbox ⇒page 63, fig. 64 .
Defining route criteria •In the Route options setup menu , press the function button.•Press the desired settings to select them in the pop-up window.
Dynamic route
If dynamic route guidance is activated, TMC traffic reports will be taken into
account in the route calculation ⇒page 70.
Excluding types of route in the calculation
The function buttons , etc. define whether or not these
types of road may be included in the route calculation.
Even when excluded, these types of route will still be included in the route
calculation if no practical alternative route exists. For example, if it is impos-
sible to reach an island without using the ferry. For the calculation of very long
routes, it is not possible to avoid motorways.
Navigation announcementsWhen the route has been calculated, the first announcement is given. Up to
three navigation announcements are given before a turn, e.g. within a town
“Prepare to turn left”, “Turn left after 300 metres” and “Now turn left”.•Press the setting knob ⇒page 8, fig. 1 to hear the last navigation
announcement again.
The distances that are announced depend on the type of road and the speed
at which you are driving. On motorways, the first announcement is given
roughly 2,000 m before an exit.
For example, the following announcements may be heard on multi-lane high-
ways or roads that divide, and at roundabouts: “Take the second exit at the
roundabout!”.
When you arrive at your destination, the following announcement is heard:
“You have reached the destination”.
During dynamic route guidance, you receive information about reported
traffic congestion on the route. If the route is recalculated due to traffic
congestion, you will be advised accordingly ⇒page 70.
Announcement settings.
Navigation announcements are played at the preset volume.
The volume of an announcement can be changed with the volume control
D.
All following announcements will then be made at this volume.
The volume of navigation announcements can be preset or switched off in the
Navigation setup menu ⇒ page 73 or in the volume settings ⇒page 88.
Route criteria
MeaningFastest route to the destination, even if it means driv-
ing further.This function aims to find an equilibrium between the
shortest time and the shortest route.Shortest route to the destination, even if it results in a
longer travelling time. The navigation route may
include unusual route sections, e.g. dirt roads.
SETUP
Route optionsRoute criteria
FastEconomicalShort
˜Avoid motorways
A10
MediaSystem2.1_EN.book Seite 64 Donnerstag, 29. April 2010 4:18 16

Navigation65
Visual recommendations on the mapWhen route guidance starts, the system automatically switches to the map
view ⇒fig. 65. The red
9 symbol indicates the vehicle's position and heading
⇒fig. 65 . If
the vehicle position symbol
9 remains in the same position and the map
view freezes, it is currently not possible to determine the vehicle's position,
e.g. in a multi-storey car park.
During route guidance the navigation route is shown as a blue line. Sections
closed to traffic either manually or due to TMC messages advising of traffic
congestion ⇒page 70 are shown in colour on the calculated route.
The next road to take is displayed in the top line of the screen.
After a few seconds, the function buttons disappear from the bottom line of
the screen to display more information on the route ⇒fig. 66.
•Briefly press the bottom-right or bottom-left area of the screen to display
the function buttons again ⇒ fig. 65.•Pressing the unit button switches between the Navigation main
menu and the map view.
When the function buttons are hidden, the current street and information
about the journey length are displayed on the bottom line of the screen
⇒ fig. 66 .: Remaining distance to the destination.: Expected time of arrival or travelling time ⇒page 73.
Shortly before you reach a turning point, a turning arrow appears, indicating
the direction to turn. The distance to the turning point is also displayed below
it.
Changing the map scale (Autozoom)
The “Autozoom” function is enabled for the map view by default. This means
that the map view automatically zooms in and out: Small scale on motorways.
Large scale in urban areas.•Turn the setting knob ⇒page 8, fig. 1 to manually change the scale
of the map for a few seconds. Turn the knob clockwise to zoom in. Turn the
knob anticlockwise to zoom out.
Fig. 65 Map view during
route guidance with the
function buttons
displayed.Fig. 66 Map view during
route guidance.
NAV
A10
MediaSystem2.1_EN.book Seite 65 Donnerstag, 29. April 2010 4:18 16

Navigation
66•To permanently retain the manually selected map scale, “Autozoom”
must be deactivated in the Navigation setup menu ⇒ page 73.
Selecting the map view mode
The map view mode can be changed.•In the map, briefly press the bottom-right or bottom-left area of the screen
to display the function buttons again.•Press the function button ⇒page 65, fig. 65 .•Select one of the playback modes displayed in the pop-up window.
: two dimensions, map oriented to North.
: two dimension, map oriented to vehicle heading.
: three dimensions, birds-eye view of map.
Alternatively, it is possible to switch between the three map views by pressing
on the compass shown on the map.
During route guidance, the calculated route can also be shown on an over-
view map.•Press in the pop-up window to display current position and
destination.
The scale of the overview map cannot be changed.•Press the function button to return to the last shown map view.
Displaying speed limits
If there is a speed limit stored in the navigation data for the road along which
you are travelling, this will be displayed on the map. During route guidance,
the arrow indicating a change of direction takes precedence over the speed
limit display.
Please remember that the navigation data may not be up-to-date and that the
system has limitations ⇒ page 47! The speed limit display is activated in the navigation system settings
⇒
page 73.
Points of interest on map
Depending on the programmed settings, points of interest (petrol stations,
car parks, Authorised Services) will be displayed as symbols on the map
⇒ page 73.
Note
If you miss a turning during route guidance and are currently unable to turn
back, keep on driving until the navigation system offers a new route.
Note
T he q ua lit y o f the i nst ru cti ons g ive n by th e uni t will d e pe nd o n th e navi gat io n
data used.
Note
In addition, the route is optimised with the TMC traffic news received
⇒page 70. The radio stations broadcasting this information are responsible
for the content and the quality of the TMC traffic reports.
Extras
2D North2D Heading3D Heading
Overview map
Back
MediaSystem2.1_EN.book Seite 66 Donnerstag, 29. April 2010 4:18 16

Navigation67
Stopping and resuming route guidanceActive route guidance can be stopped and later resumed from the new vehicle
position at any time. Stopping route guidance
•In the
map view , briefly press the bottom-right or bottom-left area of the
screen to display the function buttons.•Press the function button ⇒fig. 67 .•ALTERNATIVELY: Switch to the main menu Navigation and press the
function button.
Resume route guidance to the last destination•In the map view , pressing the function button always automatically
resumes route guidance to the last destination ⇒fig. 68 .Entering a stopover destinationIt is possible to enter one additional destination as a stopover destination
while route guidance is in progress. You will then always be guided to the
stopover destination first before route guidance continues to the final desti-
nation. The final destination is always the destination to which route guid-
Fig. 67 Stopping route
guidance.Fig. 68 Route guidance
interrupted.
Stop
Stop
Start
Fig. 69 Information
window showing a stop-
over destination during
route guidance.
MediaSystem2.1_EN.book Seite 67 Donnerstag, 29. April 2010 4:18 16

Navigation
68ance is first started. To enter a final destination and stopover destination,
please note the required steps.•To enter a stopover destination, first select a final destination and start
route guidance ⇒page 52.•Press the unit button.•In the Navigation main menu, select an additional destination, following
the same procedure as for selection of a final destination.•When you start route guidance to the additional destination, a pop-up
window opens.•Press the function button to be guided to the newly entered
destination as a stopover destination, before continuing to the final destina-
tion.•Alternatively: press the function button to cancel the
current route guidance and start a new route guidance to the newly entered
destination only.
To view the stopover destination in the information window ⇒page 67,
fig. 69 , press the ⇒page 8, fig. 1 unit button.
An announcement is given when you reach the stopover destination. After a
few seconds, route guidance is resumed to the final destination. You may
then enter another stopover destination.
If the function button is selected during route guidance to a stopover
destination ⇒page 67, you have the option of deleting the stopover
destination.
Display the information window and the list with the routeInformation window during route guidance•Press the unit button from any navigation menu (except SETUP) to open
the information window ⇒ page 58.
During route guidance, the final destination is displayed in the information
window . If a stopover destination has also been entered, this is displayed
above the final destination ⇒page 67, fig. 69.
Inserting the route list
During route guidance, a route list can be inserted via the information
window .•In the information window , press the function button.•Press the function button in the pop-up window.•The route list for the active route guidance will be calculated and
displayed ⇒fig. 70 .
NAVStopover
New destination
º
A7
Stop
Fig. 70 Route list during
route guidance.
º
Route
Route list
MediaSystem2.1_EN.book Seite 68 Donnerstag, 29. April 2010 4:18 16

Navigation69
The route list contains the names or designations of roads to be driven on
before each turning point. These are referred to below as “route sections”. All
route sections to be passed up to the next destination are displayed.
The list also shows the distance to be travelled along each route section and
the expected time required to reach the next turning point.•Turn the setting knob ⇒page 8, fig. 1 to view the route list.•Press the setting knob or Details function button to obtain more informa-
tion about a marked section in an additional information window.•Press the unit button to close the information window.
Display sections of route
The arrow
b behind an entr y in the route list indicates that more sections can
be displayed.
•Select the entry with the arrow
b by turning the setting knob and display
the sections of the route by pressing “Display”. The arrow changes to
a.
•Press the entry with the arrow
a to hide the sections of the route again.
Manually excluding sections in the route listThe sections of the journey which are marked can be excluded individually or
all together from the calculation in the route lists. Only one exclusion may be
entered at a time.•Displaying the route list ⇒ page 68.•Turn the setting knob ⇒page 8, fig. 1 to mark the first route section
of the stretch of route to be excluded.•Press the function button.
The item is marked as excluded and the function button changes to . If, instead of the button , appears in the route list, this
means that the section has already been excluded.
•Select the route section of the stretch of route you wish to exclude and
press the function button.
If the button is not active, the section to be excluded is too long.
(Max) is displayed on the bottom line of the screen after the excluded
distance.•Shorten the section of route to be excluded until the word (Max) disap-
pears and it is possible to select the function button. At the same
time, display partial sections of the route within a section of the route
⇒ page 69.
When an exclusion has been entered, the route list closes.
Route guidance will start again when the navigation system has calculated an
alternative route to the excluded section.
Re-opening a section•Press the unit button in any of the navigation menus (except SETUP).•In the information window , press the function button.•Press the function button in the pop-up window.•Alternatively:open the route list and press the function button.Note
Information on entering an exclusion starting from the current vehicle posi-
tion ⇒page 70.
Note
The excluded route section is displayed on the map ⇒page 65.
A10

A10
Exclude
Exclude to
Exclude to
Re-open
Exclude to
Exclude to
Exclude to
º
Route
Re-open section
Re-open
MediaSystem2.1_EN.book Seite 69 Donnerstag, 29. April 2010 4:18 16

Navigation
70Directly excluding a route section further ahead (congestion)During a route guidance, the route section of the remaining stretch of route
can be excluded manually.•Press the unit button in any of the navigation menus (except SETUP).•In the information window , press the function button.•Press the function button in the pop-up window.•Enter the length of the section to be excluded by turning the setting knob
⇒ page 8, fig. 1 .
The length indicated for the route section is shown on the lower line of the
screen. If (Max) is displayed, this indicates that the maximum permitted
length for exclusion has been reached.•Press the setting knob or function key to confirm the exclusion.
The excluded route section is displayed on the map.
Route guidance will start again when the navigation system has calculated an
alternative route to the excluded section.
Re-opening a section•Press the unit button in any of the navigation menus (except SETUP).•In the information window , press the function button.•Press the function button in the pop-up window.Note
It is also possible to enter or cancel an exclusion while viewing the TMC traffic
announcements using the function button ⇒ page 71.
Note
Information on manually excluding route sections further ahead
⇒page 69.Dynamic route guidance with TMC (Traffic Message Channel)The prerequisite for dynamic route guidance is always the reception of a TMC
traffic news station for the navigation area available in the unit. TMC traffic
reports received can be displayed in a list ⇒page 71.
If dynamic route guidance is activated, any TMC traffic reports are taken into
account in the route calculation.
Switching the dynamic navigation on or off•Press the unit button in one of the navigation menus.•In the Navigation setup menu , press the function button to
open the Route options setup menu ⇒ fig. 71 .
º
Route
Congestion aheadA10OK
º
Route
Re-open section
Congestion ahead
Fig. 71 Route options
setup menu.
SETUP
Route options
MediaSystem2.1_EN.book Seite 70 Donnerstag, 29. April 2010 4:18 16

Navigation71
•Alternatively: press the and buttons successively to
open the setup menu TRAFFIC .•In one of the two menus, tick or clear the checkbox in the
function button by pressing it.
Traffic incidents displayed on the map
Traffic congestion reported via TMC that is on the route is shown on the map
by a coloured symbol. Traffic congestion that is not on the route is shown on
the map by a grey symbol. The position ing of the TMC symbol indicates the
start and the direction of the traffic congestion if both are clearly defined in
the TMC traffic message.
Route sections with traffic congestion that are on the route are coloured red.
Route sections with traffic congestion that are not on the route are coloured
grey. If route guidance is not active, all traffic congestion is coloured grey.
Dynamic route guidance
If the function button is activated and a diversion to avoid
traffic congestion on the route is likely to save time, the navigation system
automatically calculates an alternative route.
An announcement is given when the route is recalculated. The same
announcement is given if traffic congestion that was present when the route
was originally calculated is now no longer reported.Note
A diversion of the route based on TMC traffic reports may not always save
time, if, for instance, there is also heavy traffic on the alternative route.
Note
If there is traffic congestion on a route section further ahead, it is possible to
exclude the section manually if the TMC traffic report has not yet been
received.
Displaying TMC traffic reports (TRAFFIC)The unit constantly receives TMC traffic reports in the background, provided
a TMC traffic news station can be received at the current location. The station
listened to does not have to be the TMC traffic news station.
TRAFFIC
SETUP
Dynamic route
’ Dynamic route
Fig. 72 List of TMC traffic
reports received.F ig. 73 Detailed view of a
received TMC traffic
report.
MediaSystem2.1_EN.book Seite 71 Donnerstag, 29. April 2010 4:18 16