2010 PORSCHE 911 GT3 Owners Manual

120
Instruments, On-Board Computer
LIMIT
Acoustic warning signal for speed limitThe acoustic warning signal can be activated for
speeds above 6 mph (10 km/h).
The signal sounds when the preset speed is
exceeded.
For the signal to sound again, the driving speed
must fall below the preset speed by at least
3mph (5km/h).
Switching on selection field “D”
fPush operating lever forward.
Setting the speed
fSelect LIMIT with the operating lever.fPush operating lever forward.10_GT3_21.book Seite 120 Donnerstag, 4. Juni 2009 12:48 12

Instruments, On-Board Computer
121
Option 1:
Accepting current speed
fPush operating lever forward.
The acoustic warning signal is activated for the
current speed.
If the vehicle is stationary, the message “Cannot
be accepted with car stopped” is displayed.Option 2:
Presetting speed
fSelect “LIMIT active” with the operating lever:
fIf “not active”, push the operating lever
forward.fSelect “xx mph” with the operating lever.
fPush operating lever forward.
Display:
not active
active
10_GT3_21.book Seite 121 Donnerstag, 4. Juni 2009 12:48 12

122
Instruments, On-Board Computer fPush operating lever slightly up or down until
the desired speed is reached.
upwards: speed is increased
downwards: speed is decreased
Note
Holding the lever up or down for a longer period
will adjust the speed in steps of 6 mph (10 km/h).
fPush operating lever forward.Switching the acoustic warning signal off
fSelect “LIMIT active” with the operating lever.
fPush operating lever forward.
Display:
10_GT3_21.book Seite 122 Donnerstag, 4. Juni 2009 12:48 12

Instruments, On-Board Computer
123
INFO
Warning messagesSwitching on selection field “D”
fPush operating lever forward.
Calling warning messages
fSelect INFO with the operating lever.fPush operating lever forward.
fSelect “Messages” with the operating lever.
fPush operating lever forward.
Any existing warning messages can be called
using the operating lever.
You also can call warning messages which were
cancelled during the trip (but only until the next
time the ignition is switched on).fPush operating lever forward.
fPush operating lever forwards or pull
backwards.
The display returns to the Info menu.
10_GT3_21.book Seite 123 Donnerstag, 4. Juni 2009 12:48 12

124
Instruments, On-Board Computer
ServiceSwitching on selection field “D”
fPush operating lever forward.
Recalling service information
fSelect INFO with the operating lever.
fPush operating lever forward.
fSelect “Service” with the operating lever.
fPush operating lever forward.
fThe time until the next service is displayed in
miles and days.
TEL
Telephone informationSwitching on selection field “D”
fPush operating lever forward.
Recalling telephone information
fSelect TEL with the operating lever.fPush operating lever forward.
10_GT3_21.book Seite 124 Donnerstag, 4. Juni 2009 12:48 12

Instruments, On-Board Computer
125
Note
You can recall phone calls, e.g. calls that arrived
during your absence, via the menu item “Missed
calls”.Example:
Selecting from the telephone book and
calling
fSelect “Phone book” with the operating lever.fPush operating lever forward.
fSelect a person to call and push the operating
lever forward.
The connection is established.
10_GT3_21.book Seite 125 Donnerstag, 4. Juni 2009 12:48 12

126
Instruments, On-Board Computer fPush the operating lever forward to end the
call.Incoming call
fSelect “Accept” or “Refuse” and push the
operating lever forward.
Note
Rejected phone calls can be recalled with the
menu item “Missed calls”.
10_GT3_21.book Seite 126 Donnerstag, 4. Juni 2009 12:48 12

Instruments, On-Board Computer
127
CHRONO
StopwatchYou can use the stopwatch to measure time inter-
vals, e.g. on the race circuit or on work-related
journeys. Measured lap times can be stored and
evaluated if the vehicle is equipped with Porsche
Communication Management (PCM).
fPlease see the chapter “Sport display” in the
separate PCM Owner’s Manual.Stopwatch on the instrument panel
The stopwatch has an analogue and a digital
display.
The large pointer of the analogue display
measures the seconds. The two small pointers
measure hours and minutes. The display re-starts
at zero after 12 hours.
Seconds and increments of 1/100th of a second
can be read on the digital display.
The digital display and the display in the on-board
computer can indicate up to 99 hours and
59 minutes.
The stopwatch can be swivelled both to the left
and to the right.
Stopwatch displays:
– on the stopwatch on the instrument panel,
– in the on-board computer menu CHRONO,
– on the performance display in the PCM.
Starting/stopping stopwatch
All stopwatch displays are started and stopped via
the on-board computer menu CHRONO.Note on operation
When you leave the CHRONO menu while the
stopwatch is running, measurement will continue.
The stopwatch stops after the ignition is switched
off. If the ignition is switched on again within
approx. 4 minutes, the stopwatch will continue to
run.
The only way to reset the stopwatch to zero is by
selecting “Reset” in the CHRONO menu.
10_GT3_21.book Seite 127 Donnerstag, 4. Juni 2009 12:48 12