2010 NISSAN ALTIMA COUPE Navigation Manual

INFO:
●Sort by Number:
The Address Book entries are displayed in as-
cending numerical order.
●Sort by Name:
The Address Book entries are displayed in al-
phabetic order.
●Sort by Icon:
By selecting a particular icon, a list that con-
tains only the Address Book entries associ-
ated with that icon is displayed.
●Sort by Group:
By selecting a particular group (family, friends,
leisure, etc.) , the selected group is displayed
at the top of the list.4. The entire route is shown on the map. Se-
lect “Start” after confirming the location of
the displayed destination. The system sets
the destination to the selected location and
starts calculating a route.
INFO:
Even after setting a destination, the location of
the destination can be adjusted, the route can be
stored, etc.
“PROCEDURES AFTER SETTING A
DESTINATION” (page 5-2)
Voice command
1. Press
located on the steering wheel
switch.2. After the tone sounds, speak a command.
To set the destination from the Address
Book:
“Navigation” “Address Book” (Standard
mode)
“Address book” (Alternate command mode)
SETTING A PREVIOUS DESTINA-
TION
A previously set destination can be set again as
the destination to which the system calculates a
route. Up to 300 previous destinations will be
automatically stored.
If the number of previous destinations exceeds
300, the oldest one will be replaced by the new
one.NDE0040NDE0041
4-18Setting a destination

1. Press DEST.
2. Select “Destinations”. A list screen is
displayed.INFO:
By selectingBy Date, the list can be sorted in
chronological order. By selectingBy Name,it
can be sorted in alphabetical order.
3. Select the preferred destination from the
list.4. The entire route is shown on the map. Se-
lect “Start” after confirming the location of
the displayed destination. The system sets
the destination to the selected location and
starts calculating a route.
INFO:
Even after setting a destination, the location of
the destination can be adjusted, the route can be
stored, etc.
“PROCEDURES AFTER SETTING A
DESTINATION” (page 5-2)
Voice command
1. Press
located on the steering wheel
switch.
NDE0042NDE0043NDE0044
Setting a destination4-19

2. After the tone sounds, speak a command.
To display the Previous Destinations list:
“Navigation” “Previous Destinations” (Stan-
dard mode)
“Previous Destinations” (Alternate com-
mand mode)
SETTING THE PREVIOUS START
POINT
The start point of the previous route guidance
can be set as the destination to which the sys-
tem calculates a route.1. Press DEST.
2. Select “Next Page”.3. Select “Previous Start Point”.NDE0045NDE0046
4-20Setting a destination

4. The previous start point is set as a
destination, and the entire route is shown on
the map. Select “Start” after confirming the
location of the displayed destination. The
system sets the destination to the selected
location and starts calculating a route.
INFO:
Even after setting a destination, the location of
the destination can be adjusted, the route can be
stored, etc.
“PROCEDURES AFTER SETTING A
DESTINATION” (page 5-2)
Voice command
1. Press
located on the steering wheel
switch.2. After the tone sounds, speak a command.
To set the previous start point as the desti-
nation:
“Previous Start Point” (Alternate command
mode)
SETTING FROM STORED ROUTES
A preferred route can be selected from the
stored routes.
1. Press DEST.
2. Select “Next Page”.
NDE0047NDE0045
Setting a destination4-21

3. Select “Stored Routes”. A list screen is
displayed.4. Select the preferred route from the list. The
route to the destination is set.5. The entire route is shown on the map. Se-
lect “Start” after confirming the location of
the displayed destination. The system sets
the destination to the selected location and
starts calculating a route.
INFO:
●Even after setting a destination, the location of
the destination can be adjusted, the route can
be stored, etc.
“PROCEDURES AFTER SETTING
A DESTINATION” (page 5-2)
●The stored route includes only locations (des-
tination and waypoints) and route calculation
conditions, not the route itself. Therefore,
when the destination is set using a stored
route, a different route may be suggested if
the current vehicle location is different from
the one when the route was stored.
NDE0048NDE0049NDE0050
4-22Setting a destination

SETTING BY PHONE NUMBER
If the telephone number of the facility is available,
use this to find the facility by entering the
number, and then have the system calculate a
route.
INFO:
●Telephone numbers that were stored for
stored destinations can also be used.
●If the area code of the specified telephone
number does not exist in the map data, the
system will not search for the location.
●Only the locations included in the database in
the map data can be searched by the phone
number. Residential phone numbers cannot
be used to search for a location.1. Press DEST.
2. Select “Next Page”.3. Select “Phone Number”. The telephone
number input screen is displayed.
NDE0045NDE0051
Setting a destination4-23

4. Enter the telephone number including the
area code.
5. After finishing the entry, select “List”.
“NUMBER INPUT SCREEN”
(page 2-11)6. Displays a list screen if there are two or
more search results. Select the preferred
destination from the list.7. The entire route is shown on the map. Se-
lect “Start” after confirming the location of
the displayed destination. The system sets
the destination to the selected location and
starts calculating a route.
INFO:
Even after setting a destination, the location of
the destination can be adjusted, the route can be
stored, etc.
“PROCEDURES AFTER SETTING A
DESTINATION” (page 5-2)
SETTING A FREEWAY
ENTRANCE/EXIT
The entrance or exit of a freeway can be set as
the destination to which the system calculates a
route.
NDE0052NDE0053NDE0054
4-24Setting a destination

1. Press DEST.
2. Select “Next Page”.3. Select “Freeway Entrance/Exit”. A character
input screen is displayed.4. Enter the name of the freeway.
5. After finishing the entry, select “List”.
NDE0045NDE0055NDE0056
Setting a destination4-25