2010 MITSUBISHI GRANDIS high beam

Exterior
E00100503558 1. Sunroof* p. 1-13
2.
Antenna p. 5-31
3. Fuel tank filler p. 03
4. Side turn-signal lamps p. 3-21, 8-25
5. Outside rear-view mirrors p. 4-07
6. Position lamps p. 3-18, 8-25, 8-28
7. Headlamps, low beam p. 3-18, 8-25, 8-26
8. Headlamps, high-beam p. 3-18, 8-25, 8-26
9. Front turn-signal lamps p. 3-21, 8-25, 8-28
10. Front fog lamps p. 3-22, 8-25, 8-28
11. Bonnet p. 8-03
12. Windscreen wipers p. 3-23 Overview1
2
3
4
5
6
8 7
9
10 1
1 12
Presented by http://mmc-manuals.ru/ \251

Indication and warning lamps
E005015019621-
CRUISE indication lamp* ® p. 4-26
2- ASC indication lamp* ® p. 4-24
3- Turn-signal indication lamps/Hazard warning indication lamps ® p. 3-06
4- Rear fog lamp indication lamp ® p. 3-06
5- Front fog lamp indication lamp ® p. 3-06
6- High-beam indication lamp ® p. 3-06
7- Diesel particulate filter (DPF) warning lamp (diesel-powered vehi-
cles)* ® p. 4-12
8- Position lamp indication lamp ® p. 3-06
9- Automatic headlamp levelling warning lamp* ® p. 3-19
10- Diesel preheat indication lamp (diesel-powered vehicles) ® p. 3-06
11- Charge warning lamp ® p. 3-08
12- Oil pressure warning lamp ® p. 3-08 13-
Check engine warning lamp ® p. 3-07, 3-08
14- TCL OFF indication lamp* ® p. 4-24
15- SONAR OFF indication lamp* ® p. 4-32
16- Anti-lock brake system (ABS) warning lamp ® p. 4-21
17- Brake warning lamp ® p. 3-06
18- Seat belt reminder/warning lamp ® p. 2-19
19- Sports mode indication lamp (vehicles with A/T) ® p. 4-18
20- Selector lever position indication lamps (vehicles with A/T, “N” indication
lamp is used also as A/T warning lamp) ® p. 4-16
21- Supplemental restraint system (SRS) warning lamp ® p. 2-42
22- Door ajar warning lamp ® p. 3-09
23- Low fuel warning lamp ® p. 3-04 Instruments and controls
3-05 3
Presented by http://mmc-manuals.ru/ \251

Indication lamps
E00501600012Turn-signal indication lamps/
Hazard warning indication
lamps
E00501700329
These
indication lamps blink on and off
when a turn-signal lamp is operating.
NOTE
l If the blinking is too fast, the
cause may be a blown lamp bulb
or a faulty turn-signal connection.
When the hazard warning lamp switch is
pressed, all turn-signal lamps will flash
on and off continuously. High-beam indication lamp
E00501800160
This

indication lamp illuminates when
the high-beam is used. Front fog lamp indication lamp
E00501900321
This

lamp illuminates while the front
fog lamps are on. Rear fog lamp indication lamp
E00502000101
This

lamp illuminates while the rear fog
lamp is on. Position lamp indication lamp
E00508900102
This

lamp illuminates with the lamp
switch at “ ” or “ ” position
Diesel preheat indication lamp
(diesel-powered vehicles)
E00502300061
This

indication lamp illuminates when
the ignition switch is placed in the “ON”
position. As the glow plug becomes hot,
the lamp goes out and the engine can be
started. If it does not go off after a few
seconds, we recommend you to have the
vehicle checked.
NOTE
l If the engine is cold, the diesel pre-
heat indication lamp is on for a lon-
ger time.
l When the engine has not been star-
ted within about 5 seconds after
the diesel preheat indication lamp
went out, return the ignition
switch to the “LOCK” position.
Then, turn the switch to the “ON”
position to preheat the engine
again.
l When the engine is warm, the die-
sel preheat indication lamp does
not come on even if the ignition
switch is placed in the “ON” posi-
tion. Warning lamps
E00502400017 Brake warning lamp
E00502501930
This

lamp illuminates when the ignition
switch is turned to the “ON” position,
and the lamp goes off after a few seconds.
Always make sure that the lamp goes off
before driving.
With the ignition switch in the “ON” po-
sition, the brake warning lamp illumi-
nates under the following conditions:
l When the parking brake lever has
been engaged.
l When the brake fluid level in the
reservoir falls to a low level.
l When the brake force distribution
function is not operating correctly. CAUTION
l
In
the situations listed below,
brake performance may be com-
promised or the vehicle may be-
come unstable if brakes are ap-
plied suddenly; consequently,
avoid driving at high speeds or
applying the brakes suddenly.
Furthermore, the vehicle
should be brought to a stop in a
safe location and to have it
checked. Instruments and controls
3-06
3
Presented by http://mmc-manuals.ru/ \251

l
When the key has been turned to either the
“LOCK” or “ACC” position or removed
from the ignition switch with the lamp
switch in the “ ”
position, and the lamp
switch is turned to the “OFF” position within
approximately 3 minutes, the auto-cutout
function will not be activated.
(Even if the lamp switch is again turned to
the “ ”
position, the lamps will not go off
automatically; the lamps will remain on as
normal.)
When you want to keep the lamps on l Turn the switch in the “OFF” position to
switch off all lamps while the key is in the
“LOCK” or “ACC” position or remove the
key from the ignition switch.
l Turn on the lamps with the switch in the
“ ”
or “ ” position again, then the
lamps will remain on.
NOTE l It is possible to disable the lamps auto-cutout
function. For further information, we recom-
mend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
Lamp monitor buzzer E00506100012
If the driver’s door is opened when the key is in the
“LOCK”

or “ACC” position or removed from the
ignition switch while the lamps are on, a buzzer
will sound to remind the driver to turn off the
lamps. When the lamp auto-cutout function acts,
the buzzer will stop automatically. When this func-
tion does not act, turn off the lamp switch to stop
the buzzer. Dipper (High/Low beam change)
E00506200114
When

the lamp switch is in the “ ”
position, the
beam changes from high to low (or low to high)
each time the lever is pulled to (1). While the high-
beam is on, the high-beam indication lamp in the in-
strument cluster will also illuminate. Headlamp flasher
E00506300333
The high-beams flash when the lever is pulled slight-
ly (2), and will go off when it is released.
When

the high-beam is on, the high-beam indica-
tion lamp in the instrument cluster will illuminate.
NOTE
l The high-beams can also flash when the
lamp switch is OFF.
l If you turn the lamps off with the headlamps
set to high-beam illumination, the headlamps
are automatically returned to their low-beam
setting when the lamp switch is next turned
to the “ ” position.Headlamp levelling
E00506400767
Headlamp levelling switch*
Except for vehicles with discharge headlamps
The

angle of the headlamp beam varies depending
on the load carried by the vehicle.
The headlamp levelling switch can be used to ad-
just the headlamp illumination distance (when the
lower beam is illuminated) so that the headlamps’
glare does not distract other drivers.
Set the switch (referring to the following table) to
the appropriate position according to the number of
people and the load in the vehicle. <6-person seat>
Vehi-
cle
condi- tion Switch
posi-tion “0” “1” “2” “3” “4” Instruments and controls
3-19 3
Presented by http://mmc-manuals.ru/ \251

l
Some fuses may not be installed on your ve-
hicle, depending on the vehicle model or spec-
ifications.
l The table above shows the main equipment
corresponding to each fuse.
The fuse box does not contain spare 7.5 A,
10 A and 15 A fuses. If a fuse of one of these
capacities blows, replace it temporarily by
borrowing the one that matches from:
7.5 A: Outside rear-view mirrors
10 A: Radio (Engine compartment)
15 A: Accessory socket
Replace the borrowed fuse as soon as possible.
Engine compartment fuse location table
Engine compartment fuse location
Front No. Symbol Electrical system Capaci-
ties
1 —
—
—*1 Battery
60 A*2
2 Radiator fan motor
50 A
*1
40 A *2
3 Anti-lock brake sys-
tem 30 A
4 Anti-lock brake sys-
tem 40 A
5 Electric window sys-
tem 40 A
6 Front fog lamps 15 A
7 AC power supply
15 A*1 Accessory socket
Accessory socket
15 A*2
8 Horn 10 A
9 Engine control
20 A
*1
10 A *2
10 Air conditioning 10 A
*1 : Petrol-powered vehicles
*2 : Diesel-powered vehicles
*3 :

Vehicles without discharge headlamps: 55 W
(H1)
*4 : Vehicles with discharge headlamps: 35 W
(D2R) No. Symbol Electrical system Capaci-
ties
11 Stop lamps 15 A
12 Horn
15 A*1 Wiper de-icer
— —
—*2
13 Alternator
7.5 A*1 Starter
25 A*2
14 Hazard warning
flasher 10 A
15 Automatic transmis-
sion 20 A
*1
— —
—*2
16 Headlamp high-beam
(right) 10 A
17 Headlamp high-beam
(left) 10 A
18 Headlamp low beam
(right) 10 A
*3
20 A *4
19 Headlamp low beam
(left) 10 A
*3
20 A *4
*1 : Petrol-powered vehicles
*2 : Diesel-powered vehicles
*3 :
Vehicles without discharge headlamps: 55 W
(H1)
*4 : Vehicles with discharge headlamps: 35 W
(D2R) Maintenance
8-22
8
Presented by http://mmc-manuals.ru/ \251

4. Insert a new fuse of the same capacity by us-
ing the fuse puller and insert the fuse at the
same place in the fuse block. CAUTION
l
If
the newly inserted fuse blows again af-
ter a short time, we recommend you to
have the electrical system checked to find
the cause and rectify it.
l Never use a fuse with a capacity larger
than that specified or any substitute, such
as wire, foil, etc.; doing so will cause the
circuit wiring to heat up and could cause
a fire. Replacement of lamp bulbs
E01003100622
Before

replacing a bulb, ensure the lamp is off. Do
not touch the glass part of the new bulb with your
bare fingers; the skin oil left on the glass will evap-
orate when the bulb gets hot and the vapour will
condense on the reflector and dim the surface. CAUTION
l
Bulbs
are extremely hot immediately af-
ter being turned off.
When replacing a bulb, wait for it to cool
sufficiently before touching it. You could
otherwise be burnt.
NOTE l If

you are unsure of how to carry out the
work as required, we recommend you to con-
sult a specialist.
l Be careful not to scratch the vehicle body
when removing a lamp and lens.
l When it rains or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy. This is the same phenomenon
as when window glass mists up on a humid
day, and does not indicate a functional prob-
lem.
When the lamp is switched on, the heat will
remove the fog. However, if water gathers in-
side the lamp, we recommend you to have it
checked.
Bulb capacity E01003200043
When replacing a bulb, use a new bulb with the
same wattage and colour. Outside
E01003302051 1- Front turn-signal lamps: 21 W (W21W)
2-

Headlamps, high-beam: 65 W (H9)
3- Front fog lamps: 51 W (HB4)
4- Headlamps, low beam without discharge lamp: 55 W (H1)
Headlamps, low beam with discharge lamp:
35 W (D2R)
5- Position lamps: 5 W (W5W)
6- Side turn-signal lamps

Codes in parentheses indicate bulb types. Maintenance
8-25 8
Presented by http://mmc-manuals.ru/ \251

1- High-mounted stop lamp
2-
Stop and tail lamps
3- Rear fog lamp (LHD vehicles): 21 W (W21W) Reversing lamp (RHD vehicles): 21 W
(W21W)
4- Licence plate lamps: 5 W (W5W)
5- Reversing lamp (LHD vehicles): 21 W (W21W)
Rear fog lamp (RHD vehicles): 21 W (W21W)
6- Rear turn-signal lamps: 21 W (WY21W)

Codes in parentheses indicate bulb types.
NOTE l The side turn-signal lamps, stop and tail
lamps and high-mounted stop lamp use
LEDs rather than bulbs. For repair and re-
placement, we recommend you to consult a
specialist. Inside
E01003400986 1- Rear personal lamps: 8 W
2-

Room lamp & map lamps: 8 W
3- Vanity mirror lamps*: 3 W
4- Glove box lamp: 1.4 W
5- Door lamps: 3.4 W
6- Luggage compartment lamp: 5 W Headlamps
E01003501290
Replacement of low beam (except for vehicles
with discharge headlamps) 1. Pull

out the connector (B) while pressing the
tab (A). Turn the cap (C) anticlockwise and
remove it. 2. Pull the socket (D) off the bulb.Maintenance
8-26
8
Presented by http://mmc-manuals.ru/ \251

3. Unhook the spring (E), which secures the
bulb, and remove the bulb. 4. To
install the bulb, perform the removal
steps in reverse. CAUTION
l
Handle
halogen lamp bulbs with care.
The gas inside halogen lamp bulbs is high-
ly pressurized, so dropping, knocking, or
scratching a halogen lamp bulb can cause
it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the
bulb to break the next time the head-
lamps are operated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner, etc.,
and refit it after drying it thoroughly. Replacement of low beam (for vehicles with dis-
charge headlamps)
Do

not attempt to disassemble or repair discharged
headlamps, and do not attempt to replace their bulbs. CAUTION
l
A high voltage is present in the power cir-
cuit

and in the bulbs and bulb terminals.
To avoid the risk of an electric shock, con-
tact a MITSUBISHI MOTORS Author-
ized Service Point whenever repair or re-
placement is necessary. Replacement of high-beam
1. For
diesel-powered vehicles, remove the
bolts (A) to remove the power steering reser-
voir tank (B). 2. Pull
out the connector (D) while pressing the
tab (C). Turn the cap (E) anticlockwise and
remove it. Maintenance
8-27 8
Presented by http://mmc-manuals.ru/ \251