2010 MITSUBISHI GRANDIS instrument panel

SRS warning lamp
E00407800653
There
is a Supplemental Restraint System (“SRS”)
warning lamp on the instrument panel. The system
checks itself and the lamp tells you if there is a prob-
lem. When the ignition switch is turned to the
“ON” or “START” position, the warning lamp
should illuminate for several seconds and then
should go out. This means the system is ready. If
an SRS airbag or pretensioner seat belt is not oper-
ating properly, the warning lamp comes on and
stays on.
The SRS warning lamp is shared by the following:
l Driver’s airbag
l Front passenger’s airbag
l Side airbags
l Curtain airbags
l Seat belt pretensioners
l Driver’s seat position sensor
l Front passenger’s airbag ON-OFF switch WARNING
l If
any of the following conditions occur,
the SRS and/or seat belt pretensioners
are not working properly, and we recom-
mend you to have it inspected by a
MITSUBISHI MOTORS Authorized
Service Point immediately. • The SRS warning lamp does not illu-minate when you start the vehicle.
• The SRS warning lamp does not go out after several seconds.
• The SRS warning lamp illuminates while driving.
SRS servicing E00407900726 WARNING
l We
recommend any maintenance per-
formed on or near the components of the
SRS to be performed by a MITSUBISHI
MOTORS Authorized Service Point.
Improper work on the SRS components
or wiring could result in inadvertent de-
ployment of the airbags, or could render
the SRS inoperative; either situation
could result in serious injury.
l Do not modify your steering wheel, seat
belt retractor or any other SRS compo-
nents. For example, replacement of the
steering wheel, or modifications to the
front bumper or body structure can ad-
versely affect SRS performance and lead
to possible injury. WARNING
l If
your vehicle has sustained any damage,
we recommend you to have the SRS in-
spected to ensure it is in proper working
order.
l Do not modify your front seats, centre pil-
lar and centre console.
It can adversely affect SRS performance
and lead to possible injury.
Also, if you have found any tear or open
seam in the seat fabric at the portion near
the side airbag, we recommend you to
have the seat inspected.
l If you have found any scratch, crack or
damage to the portion of the front and
rear pillars and roof side rail, you should
have the SRS inspected by a
MITSUBISHI MOTORS Authorized
Service Point.
NOTE l When

you transfer ownership of the vehicle
to some other person, we urge you to alert
the new owner that it is equipped with the
SRS and refer the new owner to the applica-
ble section in this owner’s manual.
l If you junk or scrap the vehicle, we urge you
to first take the vehicle to a MITSUBISHI
MOTORS Authorized Service Point so that
the SRS can be rendered safe. Seat and seat belts
2-42
2
Presented by http://mmc-manuals.ru/ \251

Low fuel warning lamp
E00508100638
The
warning lamp (A) illuminates when the fuel lev-
el is getting low (approx. 10 litres) with the igni-
tion switch in the “ON” position. Refuel as soon as
possible. NOTE
l On

inclines or curves, due to the movement
of fuel in the tank, the low fuel warning lamp
may indicate incorrectly. Water temperature gauge
E00500800495
The

water temperature gauge indicates the engine
coolant temperature when the ignition switch is in
the “ON” position. CAUTION
l
If
the indication needle enters the zone
(A) while the engine is running, it indi-
cates that the engine is possibly overheat-
ing. Immediately park your vehicle in a
safe place and make the necessary correc-
tions. (Refer to “Engine overheating” on
page 6-04.)
While driving, care should always be tak-
en to maintain the normal operating tem-
perature.
Daytime dipper button E00508800026
By pressing the daytime dipper button, you can
change

the brightness of the backlighting in meters
and instrument panel. NOTE
l The

brightness can be adjusted among 4 lev-
els in accordance with the on/off condition of
the tail lamps. NOTE
l The

meter brightness is memorized and main-
tained even if the ignition switch is turned to
the “LOCK” position. Instruments and controls
3-04
3
Presented by http://mmc-manuals.ru/ \251

l
To cancel the unit setting procedure before
completion, press the button (A). l
The
outside temperature and digital clock are
not shown during the unit selecting procedure.
l If the “SET” button is not pressed for about
15 seconds or longer in the middle of the se-
lection, the currently selected unit is set auto-
matically. The display will return to the orig-
inal display item. Combination headlamps and
dipper switch E00506000776
Headlamps
Rotate the switch to turn on the lamps. OFF All lamps off
Position, tail, licence plate and instrument
panel lamps on
Headlamps and other lamps go on
NOTE
l Do

not leave the headlamps and other lamps
on for a long while the engine is stationary.
A run-down battery could result. l
When
it rains or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy. This is the same phenomenon
as when window glass mists up on a humid
day, and does not indicate a functional prob-
lem. When the lamp is switched on, the heat
will remove the fog. However, if water gath-
ers inside the lamp, we recommend you to
have it checked.
[Vehicles with Daytime Running Lamp]
When the ignition switch is in the “ON” position
and the lamp switch is set to the “OFF” position,
the low beam of the headlamps, tail lamps, etc.,
will illuminate.
Lamps (headlamps, fog lamp, etc.) au-
to-cutout function l If the key is turned to the “LOCK” or
“ACC” position or removed from the igni-
tion switch and the lamps will stay on for
about 3 minutes without opening the driver’s
door while the lamp switch in the “ ” posi-
tion, automatically turn off.
l If

the key is turned to the “LOCK” or
“ACC” position or removed from the igni-
tion switch and the driver’s door is opened
within 3 minutes while the lamp switch in
the “ ”
position, a buzzer will sound to
warn the driver that the lamps have not been
turned off, and these lamps will automatical-
ly turn off.
NOTE l The lamp auto-cutout will not function when
the lamp switch is in the “ ” position.Instruments and controls
3-18
3
Presented by http://mmc-manuals.ru/ \251

NOTE
l To
avoid erroneous operation, move the se-
lector lever firmly into each position and brief-
ly hold it there. Always check the position
shown by the selector lever position indica-
tion lamp after moving the selector lever.
l If the brake pedal is not depressed and held,
the shift-lock device activates to prevent the
selector lever from being moved from the
“P” (PARK) position.
l For a shift indicated by in the illustration,
depress

the brake pedal before moving the se-
lector lever. If you attempt to move the selec-
tor lever before depressing the brake pedal,
the selector lever may become immovable. Selector lever position indication
lamps/“N” indication lamp
E00603500452 A- Selector lever position indication lamps
When
the ignition switch is turned to the
“ON” position, the indication lamps in the
instrument panel illuminate to show the po-
sition of the selector lever (i.e. “PARK”,
“DRIVE”, “REVERSE”, etc.).
B- “N” indication lamp When
the “N” indication lamp blinks with
the “D” (DRIVE) position or “Sports
mode” being selected, the A/T may be mal-
functioning. CAUTION
l
If
a malfunction occurs in the A/T while
driving, the “N” indication lamp will blink.
In this case, immediately park your vehi-
cle in a safe place and follow these proce-
dures:
(The “N” indication lamp warning func-
tion does not operate with the selector lev-
er in the “P” (PARK), “R” (REVERSE)
or “N” (NEUTRAL) position.)
[The “N” indication lamp blinks rapidly
(twice per second)]
The automatic transmission fluid is over-
heating.
Park your vehicle in a safe place but do
not turn off the engine. Move the selector
lever to the “P” (PARK) position and
open the bonnet. Keep the engine idling.
After a while, move the selector lever to
the “D” (DRIVE) position and confirm
that the “N” indication lamp stops blink-
ing. It is safe to continue driving if the
“N” indication lamp no longer is no lon-
ger blinking.
If the “N” indication lamp continues blink-
ing or blinks intermittently, we recom-
mend you to have your vehicle inspected.
[The “N” indication lamp blinks slowly
(once per second)]
The A/T safety device may be operating
due to a malfunction.
We recommend you to have your vehicle
inspected as soon as possible. Starting and driving
4-16
4
Presented by http://mmc-manuals.ru/ \251

CAUTION
l
By rapidly moving the selector lever back-
wards (SHIFT DOWN) twice, it is possi-
ble to skip one gear, i.e., 3 rd
to 1 st
or 4 th
to
2 nd
. Since sudden engine braking and/or
rapid acceleration can cause a loss of trac-
tion, however, downshifts must be made
carefully in accordance with the vehicle’s
speed.
NOTE l In

sports mode, only the 4 forward gears can
be selected. To reverse or park the vehicle,
move the selector lever to the “R” (RE-
VERSE) or “P” (PARK) position as required.
l To maintain good running performance, the
transmission may refuse to perform an up-
shift when the selector lever is moved to the
“+” (SHIFT UP) position at certain vehicle
speeds. Also, to prevent over-revving of the
engine, the transmission may refuse to per-
form a downshift when the lever is moved to
the “-” (SHIFT DOWN) position at certain
vehicle speeds.
l In sports mode, downward shifts are made au-
tomatically when the vehicle slows down.
When the vehicle stops, 1 st
gear is automati-
cally selected. l
When
driving away on a slippery road, push
the selector lever forward into the “+”
(SHIFT UP) position. This causes the trans-
mission to shift into the 2 nd
gear which is bet-
ter for smooth driving away on a slippery
road. Push the selector lever to the “-”
(SHIFT DOWN) side to shift back to the 1 st
gear.
l Move the selector lever gently between the
manual and main gates and between posi-
tions in the manual gate. Undue force could
damage the selector lever.
Sports mode indication lamp E00612300010
In sports mode, the currently selected position is in-
dicated on the instrument panel. NOTE
l When

sports mode is selected, the “D” indi-
cation lamp goes off. Operation of the A/T
E00604200065 CAUTION
l
Before
selecting a gear with the engine
running and the vehicle stationary, fully
depress the brake pedal to prevent the ve-
hicle from creeping.
The vehicle will begin to move as soon as
the gear is engaged, especially when the
engine speed is high, at fast idle or with
the air conditioning operating, the brakes
should only be released when you are
ready to drive away.
l Depress the brake pedal with the right
foot at all times.
Using the left foot could cause driver move-
ment delay in case of an emergency.
l To prevent sudden acceleration, never
race the engine when shifting from the
“P” (PARK) or “N” (NEUTRAL) position.
l Operating the accelerator pedal while the
other foot is resting on the brake pedal
will affect braking efficiency and may
cause premature wear of brake pads.
Do not race the engine with brake pedal
pressed.
This can damage the transmission.
Also, when the vehicle is stationary, the
engine revolutions may not rise to the
same revolutions as measured in normal
starting even if the accelerator pedal is de-
pressed while the brake pedal is being
pressed. Starting and driving
4-18
4
Presented by http://mmc-manuals.ru/ \251

NOTE
l The
interior lamps auto-cutout function can
be deactivated. We recommend you to con-
sult a MITSUBISHI MOTORS Authorized
Service Point for detailed information and as-
sistance.
On a vehicle equipped with a Multi Display
Station (MDS), the functions can be adjusted
on the screen. Refer to the separate operation
manual for details. Storage spaces
E00713100928 CAUTION
l
Never
leave lighters, cans of carbonated
drink, and spectacles in the cabin when
parking the vehicle in hot sunshine. The
cabin will become extremely hot, so light-
ers and other flammable items may catch
fire and unopened drink cans (including
beer cans) may rupture. The heat may al-
so deform or crack plastic spectacle len-
ses and other spectacle parts that are
made of plastic.
l Keep the lids of storage spaces closed
while driving the vehicle. A lid or the con-
tents of a storage space could otherwise
cause injuries.
NOTE l Do

not leave valuables in any storage space
when leaving the vehicle. 1- Rear side box
2-

Personal box
3- Sunglasses pocket*
4- Instrument panel upper box
5- Luggage floor box
6- Glove box
Glove box E00717600471
The glove box can be locked and unlocked using
the key. 1- To lock
2-

To unlock
3- To open, pull the lever For pleasant driving
5-38
5
Presented by http://mmc-manuals.ru/ \251

NOTE
l When
the lamp switch is in the “ ”
or
“ ”
position, the glove box lamp illumi-
nates.
l The owner’s manual can be stored in the up-
per area (A) of the glove box. Instrument panel upper box
E00717700023
To open, push the button. Personal box
E00718000023
To open, pull the lid (A). Sunglasses pocket*
E00718600218
To open, push the lid. CAUTION
l
The holder should not be used to store any-
thing heavier than sunglasses. These ob-
jects could drop out and lead to a collision.
NOTE l The

holder may not be able to accomodate ev-
ery possible size and shape of sunglasses; it
is advisable to check compatibility before use.
Rear side box E00718100024
The rear side box is located on the left side of the
third seat. Open the lid to use it. Luggage floor box
E00718700020
The box for storing articles is located inside the lug-
gage compartment. For pleasant driving
5-39 5
Presented by http://mmc-manuals.ru/ \251

Coolant 8-06,9-15
Number 9-02
Oil 8-04
Oil and oil filter
9-14
Overheating 6-04
Specifications 9-08
Used engine oils safety instructions and disposal
information 06
Water temperature gauge 3-04
Error codes 5-28
Exterior and interior lamp operation 8-18
FFluid capacities and lubricants 9-14
Fluid
Automatic transmission fluid

8-08,9-15
Brake fluid 8-09,9-14
Clutch fluid 8-09,9-14
Engine coolant 8-06,9-15
Power steering fluid 8-09,9-14
Washer fluid 8-08,9-14
For cold and snowy weather 8-19
Front automatic air conditioning 5-05
Front fog lamps Bulb capacity 8-25
Indication lamp 3-06
Replacement 8-28
Front fog lamp Switch 3-22
Front seat 2-05
Front turn-signal lamps Bulb capacity 8-25
Replacement 8-28
Fuel consumption 9-13
Fuel Filling the fuel tank 03
Fuel gauge 3-03
Fuel selection 02 Low fuel warning lamp 3-04
Modification/alterations to the electrical or fuel
systems 05
Tank capacity

03
Fuse load capacity 8-20
Fuse replacement 8-24
Fuses 8-20
Fusible links 8-19
G Gauges 3-05
General maintenance

8-18
General vehicle data 9-04
Genuine parts 05
Glove box 5-38
Glove box lamp Bulb capacity 8-26
Replacement 8-32
H Handling of compact discs 5-30
Hazard warning indication lamps

3-06
Head restraints 2-11
Headlamp levelling 3-19
Headlamp levelling switch 3-19
Headlamps Bulb capacity 8-25
Headlamp flasher 3-19
Replacement 8-26
Switch 3-18
Heated mirror 4-08
Heated seats 2-06
High-beam indication lamp 3-06
Hinges and latches lubrication 8-19
Horn switch 3-26 I If the vehicle breaks down 6-02
Ignition switch 4-08
Indication and warning lamps

3-05
Indication lamps 3-06
Inside rear-view mirror 4-06
Inside tailgate release 1-10
Installation of accessories 04
Instrument panel upper box 5-39
Instruments 3-02
Interior lamp switch 5-36
Interior lamps 5-35
J Jacking up the vehicle 6-07
Jack 6-06
Storage 6-06
Jump starting (Emergency starting)

6-02
K Keyless entry system 1-04
Keys 1-02
L Labeling 9-02
Lamp monitor buzzer

3-19
Lamps (headlamps, fog lamp, etc.) auto-cutout func-
tion 3-18
Lamps (room lamps, etc.) auto-cutout function (Ve-
hicles with keyless entry system) 5-37
Leakage (Fuel, engine coolant, oil and exhaust
gas) 8-18
Licence plate lamps Bulb capacity 8-26 Alphabetical index
2
Presented by http://mmc-manuals.ru/ \251