The DVD changer* loads the disc into the
selected magazine tray. You see the Load‐
ing disc ... message.
i The loading process depends on the disc
type and may take a while. If no disc is
inserted for approximately 20 seconds, the
display returns to the magazine menu.
The DVD changer* plays the disc if:
R it has been inserted correctly.
R it is a permissible type of disc. 0001
Loaded magazine tray (ejecting possible)
0002 Empty magazine tray
X To exit the menu: press the0011button
again.
or
X Select Back.
or
X Press the 0001back button next to the
COMAND controller.
Loading empty magazine trays
X Press the 0011button.
The magazine menu appears.
X Select Fill empty slots.
You see the Please wait... message.
COMAND switches to the next empty mag-
azine tray. Then you see the Please
insert disc . message.
i Never insert a data medium before
COMAND prompts you to do so. Never
insert more than one disc at a time into a
magazine tray. X
Slide the disc into the slot with the printed
side facing upwards.
You see the Please wait... message.
Once the disc is loaded, the DVD
changer* switches to the next empty tray.
You see the Please insert disc
message.
X Repeat the last step until all trays are loa-
ded.
The DVD changer* plays the last disc loa-
ded, even if the loading procedure has not
been carried out for every magazine tray.
X To complete loading: press the0011but-
ton again.
or
X Select Back.
or
X Press the 0001back button next to the
COMAND controller.
Loading a PCMCIA memory card COMAND supports 16-bit full-size type
Iand
II PCMCIA memory cards.
i Not all PCMCIA memory cards and stor-
age media are designed for the tempera-
tures which may be reache dinthe vehicle.
Due to the wide range of PCMCIA memory
cards available on the market, playback
cannot be guaranteed for all brands of
PCMCIA memory card.
The readable storage capacity depends on
the PCMCIA memory card used. Further
information can be obtained from a
Mercedes-Benz Service Centre. Audio
169COMAND APS
*optional
BA 197 ECE RE 2010/6a; 1; 2, en-GB
sabbaeu
Version: 3.0.3.6 2010-05-07T14:19:43+02:00 - Seite 169 Z
X
Open stowage compartment 0001.
X Remove the TIREFIT kit, wheel chock, cen-
tring pin and gloves. G
Risk of injury
The jack is designed only to raise and hold the
vehicle for a short time while a wheel is being
changed.
You must use stands if you are carrying out
work on the vehicle.
Make sure that the jack is placed on a firm,
non-slip, level surface. Do not use wooden
blocks or similaro bjects as a jack underlay.
Otherwise, the jack will not be able to achieve
its load-bearing capacity due to the restricted
height.
Do not start the engine at any time while a
wheel is being changed.
i When using the jack, you should also
observe the safety notes in the "Flat tyre"
section (Y page 325). Fire extinguisher*
i Have the fire extinguisher refilled after
each use and checked every one or two
years. It may otherwise fail in an emer-
gency.
Observe the legal requirements in all coun-
tries concerned.
The fire extinguisher is located under the left-
hand front seat. X
Pull tab 0001upwards.
X Remove fire extinguisher 0002forwards. First-aid kit
i Check the expiry date of the first-aid kit
annually, and replace the contents when
necessary.
The first-aid kit is located in the left-hand
stowage compartment in the boot. X
Turn fastener 0002in the direction of the
arrow.
X Open stowage compartment 0001.
X Open the Velcro fastener and remove the
first aid kit. Display messages
Notes
G
Risk of accident
The on-board computer only records and dis-
plays malfunctions and warnings from certain
systems .For this reason, you should always
make sure that your vehicle is safe to use. You
could otherwise cause an accident by driving
an unsafe vehicle.
Certain display messages are accompanied
by a warning tone or acontinuous tone.
The multifunction display shows high-priority
display messages in red. Display messages
289Practical advice
*optional
BA 197 ECE RE 2010/6a; 1; 2, en-GB
sabbaeu
Version: 3.0.3.6 2010-05-07T14:19:43+02:00 - Seite 289 Z
