2010 Lexus IS250C Owner's Manual

120
1-7. Safety information
10_IS250C/350C_U
Installing child restraints
Follow the child restraint system manufacturer's instructions. Firmly
secure child restraints to the rear seats using the LATCH anchors or a seat
belt. Attach the top tether strap when installing a child restraint.
The lap/shoulder belt can be used if your child restraint system is not com-
patible with the LATCH (Lower Anchor s and Tethers for Children) system.
Child restraint LATCH anchors
LATCH anchors are provided
for each rear seat. (Buttons dis-
playing the location of the
anchors are attached to the
seats.)
Seat belts equipped with a child
restraint locking mechanism
(ALR/ELR belts except driver’s
seat belt) (→P. 6 5 )
Anchor bracket (for top tether
strap)
Anchor brackets are provided
for both rear seats.

121
1-7. Safety information
1
Before driving
10_IS250C/350C_U
Installation with LATCH systemTy p e A Latch the hooks of the
lower straps onto the
LATCH anchors.
If the child restraint has a
top tether strap, the top
tether strap should be
latched onto the top tether
strap anchors.
For owners in Canada:
The symbol on a child restraint sys-
tem indicates the presence of a
lower connector system.
Canada only
STEP1
STEP2

122
1-7. Safety information
10_IS250C/350C_UType B
Latch the buckles onto the
LATCH anchors.
If the child restraint has a
top tether strap, the top
tether strap should be
latched onto the top tether
strap anchors.
For owners in Canada:
The symbol on a child restraint sys-
tem indicates the presence of a
lower connector system.
Canada only
STEP1
STEP2

123
1-7. Safety information
1
Before driving
10_IS250C/350C_U
Installing child restraints using a seat belt (child restraint lock function belt)
■Rear facing  Infant seat/convertible seat
Place the child seat on the rear
seat facing the rear of the vehicle.
Run the seat belt through the child
seat and insert the plate into the
buckle. Make sure that the belt is
not twisted.
Fully extend the shoulder belt and
then allow it to retract slightly in
order to activate the ALR lock
mode.
Lock mode allows the seat belt to
retract only.
STEP1
STEP2
STEP3

124
1-7. Safety information
10_IS250C/350C_UWhile pushing the child seat down
into the rear seat, allow the shoul-
der belt to retract until the child
seat is securely in place.
After the shoulder belt has
retracted to a point where there is
no slack in the belt, pull the belt to
check that it cannot be extended.
■
Forward facing  Convertible seat
Place the child seat on the seat
facing the front of the vehicle.
Run the seat belt through the child
seat and insert the plate into the
buckle. Make sure that the belt is
not twisted.
Fully extend the shoulder strap and
then allow it to retract slightly into
the ALR lock mode.
Lock mode allows the seat belt to
retract only.
STEP4
STEP1
STEP2
STEP3

125
1-7. Safety information
1
Before driving
10_IS250C/350C_UWhile pushing the child seat into
the rear seat, allow the shoulder
belt to retract until the child seat is
securely in place.
After the shoulder belt has
retracted to a point where there is
no slack in the belt, pull the belt to
check that it cannot be extended.
If the child restraint has a top tether strap, the top tether strap
should be latched onto the top tether strap anchors.
■ Booster seat
Place the booster seat on the seat
facing the front of the vehicle.
Sit the child in the booster seat. Fit
the seat belt to the booster seat
according to the manufacturer's
instructions and insert the plate
into the buckle. Make sure that the
belt is not twisted.
Check that the shoulder belt is cor-
rectly positioned over the child's
shoulder, and that the lap belt is as
low as possible. (→
P. 6 5)
STEP4
STEP5
STEP1
STEP2

126
1-7. Safety information
10_IS250C/350C_U
Removing a child restraint installed with a seat beltPush the buckle release button
and fully retract the seat belt.
Child restraint systems with a top tether strapSecure the child restraint using a
seat belt or a lower anchors.
STEP1

127
1-7. Safety information
1
Before driving
10_IS250C/350C_UPass the end of the top tether strap
through the gap between the seat
and the head restraint. Fold the
head restraint forward into the
stowed position. (
→P. 6 2 ) O p e n
the anchor bracket cover, latch the
hook onto the anchor bracket and
tighten the top tether strap. Return
the head restraint to the upright
position.
Make sure the top tether strap is
securely latched.
Close the anchor bracket cover
after install the child restraint sys-
tem.
STEP2
■When installing a child restraint system with lower anchors and a top tether strap
Depending on the child restraint system's size and shape, if the child restraint sys-
tem is installed to the LATCH anchors first, it may not be possible to attach the top
tether strap to the anchor bracket.
In that case, first temporarily attach the top tether strap to the anchor bracket, install
the child restraint system using the lower anchors and then tighten the top tether
strap.
■Laws and regulations pe rtaining to anchorages
The LATCH system conforms to FMVSS225 or CMVSS210.2.
Child restraint systems conforming to FMVSS213 or CMVSS213 specifications
can be used.
This vehicle is designed to conform to the SAE J1819.