2010 JAGUAR XFR ignition

Operating Temperature Range -40 to 160 °C (-40 to 320 °F) Oil Level Check

For additional information, refer to Engine Oil Draining and Filling (303-01A, General Procedures).

For accuracy, oil level checks should be performed with the vehicle on level ground when the oil is hot. The vehicle needs to
stand for approximately 10 minutes, after the engine is switched off, to allow the oil to drain back into the sump pan and the
oil level to stabilize. The oil level system will not give a reading until the oil level has stabilized.

With the ignition on, the engine stopped and the transmission in P (park), repeatedly press the trip button on the end of the
LH multifunction switch until the oil level icon and applicable message are displayed in the fuel gage/trip computer area of the message center, as shown below:



Item Description A Oil level is between 50% and 100% of recommended level. No top-up required. B Oil level is between 12.5% and 50% percent of recommended level. Add 0.5 liter (0.53 US quart) of oil. C Oil level is between 0% and 12.5% of recommended level. Add 1 liter (1.06 US quarts) of oil. D Oil level is above maximum for safe operation. Reduce oil level to recommended level. E Oil level is below minimum for safe operation. Add 1.5 liters (1.59 US quarts) of oil, then recheck level. F Oil level is stabilizing. Wait 10 minutes and then recheck level. If this display is accompanied by the message ENGINE OIL LEVEL MONITOR SYSTEM FAULT, a fault with the oil level monitoring system is indicated. System Fault Warning

If there is a fault with the system, in addition to being displayed during an oil level check, the message ENGINE OIL LEVEL
MONITOR SYSTEM FAULT will be temporarily displayed when the ignition is first switched on.

Refer to: Specifications (303-01D Engine - V8 S/C 5.0L Petrol, Specifications).
Clean any residual engine oil from the oil filler cap area.

6.













7. CAUTION: Make sure that the vehicle has been left for 5 minutes
from filling with oil.

Follow the Steps 9-13 before starting the engine.

8.
Start the engine and allow to run for 10 minutes, stop the
engine.
Check for leaks.

9. CAUTIONS:


Make sure that the selector lever and the gearshift mechanism are
in the park (P) position.


Make sure that the hood is open.
Turn the ignition on.

12.
The message center display will revert to the normal
display in the trip computer.
Scroll through the trip menu to access the engine oil
level display.
Check that the oil level display shows an oil level
reading.
Only after having started and run the engine for 10
minutes (as indicated in Step 8), switch off the
engine, then stabilizing for 10 minutes, take a
reading from the oil level display and, if necessary
top up with engine oil.





















13. NOTE: If instructed to follow Steps 9-13 in a previous step, return
to Step 8 and continue the procedure.
Turn the ignition off.

14. Allow 10 minutes for the engine oil level to stabilize if there has been
additional oil top up.


15. NOTE: The following steps are to update the average
oil level value.
Turn the ignition on.
Press and hold the cruise control cancel button for
more than 2 seconds. www.JagDocs.com

Specifications).
Clean any residual engine oil from the oil filler cap area.

4.













5. CAUTION: Make sure that the vehicle has been left for 5 minutes
from filling with oil.

Follow the Steps 7-11 before starting the engine.

6.
Start the engine and allow to run for 10 minutes, stop the
engine.
Check for leaks.

7. CAUTIONS:


Make sure that the selector lever and the gearshift mechanism are
in the park (P) position.


Make sure that the hood is open.
Turn the ignition on. www.JagDocs.com

10.
The message center display will revert to the normal
display in the trip computer.
Scroll through the trip menu to access the engine oil
level display.
Check that the oil level display shows an oil level
reading.
Only after having started and run the engine for 10
minutes (as indicated in Step 6), switch off the
engine, then stabilizing for 10 minutes, take a
reading from the oil level display and, if necessary
top up with engine oil.





















11. NOTE: If instructed to follow Steps 7-11 in a previous step, return
to Step 6 and continue the procedure.
Turn the ignition off.

12. Allow 10 minutes for the engine oil level to stabilize if there has been
additional oil top up.


13. NOTE: The following steps are to update the average
oil level value.
Turn the ignition on.
Press and hold the cruise control cancel button for
more than 2 seconds.

17.
18. Torque: 10 Nm


















NOTE: Install a new sealing washer.

Torque: 24 Nm









19.




20. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).



CAUTION: Make sure that the vehicle is left for 5 minutes from filling with oil and
that the engine oil level is reading at least minimum (by following Steps 23-27), before
starting the engine.

Fill the engine with oil - for filling values on vehicles without supercharger:

Refer to: Specifications (303-01C Engine - V8 5.0L Petrol, Specifications). Fill the engine with oil - for filling values on vehicles with supercharger:

Refer to: Specifications (303-01D Engine - V8 S/C 5.0L Petrol, Specifications). Clean any residual engine oil from the oil filler cap area.


21.
oil. CAUTION: Make sure that the vehicle has been left for 5 minutes from filling with

Follow the Steps 23-27 before starting the engine.

22.
Start the engine and allow to run for 10 minutes, stop the engine.
Check for leaks.

23. CAUTIONS:


Make sure that the selector lever and the gearshift mechanism are in the park (P)
position.


Make sure that the hood is open.
Turn the ignition on.

26.
The message center display will revert to the normal display in the
trip computer.
Scroll through the trip menu to access the engine oil level display.
Check that the oil level display shows an oil level reading.
Only after having started and run the engine for 10 minutes (as
indicated in Step 22), switch off the engine, then stabilizing for 10
minutes, take a reading from the oil level display and, if necessary
top up with engine oil.





















27.
NOTE: If instructed to follow Steps 23-27 in a previous step, return to Step 22 and
continue the procedure.

Turn the ignition off.

28.
Allow 10 minutes for the engine oil level to stabilize if there has been additional oil top
up.


29. NOTE: The following steps are to update the average oil level value.

Turn the ignition on.
Press and hold the cruise control cancel button for more than 2
seconds.














30.
The message center display will revert to the normal display in the trip computer.

31. Turn the ignition off.

32. Turn the ignition on. www.JagDocs.com

Refer to: Specifications (303-01D Engine - V8 S/C 5.0L Petrol, Specifications).
Clean any residual engine oil from the oil filler cap area.


13. CAUTION: Make sure that the vehicle has been left for 5 minutes
from filling with oil.
Follow the Steps 15-19 before starting the engine.

14.
Start the engine and allow to run for 10 minutes, stop the
engine.
Check for leaks.

15. CAUTIONS:


Make sure that the selector lever and the gearshift mechanism are
in the park (P) position.


Make sure that the hood is open.
Turn the ignition on.

16.
Scroll through the trip menu to access the engine oil
level display. www.JagDocs.com