2010 JAGUAR XFR Bolt

Lower 3 bolts.

Torque: 9 Nm www.JagDocs.com

Wiper arm retaining nuts 22 16.2 194.7 Wiper linkage bolts / screws 11 8.1 97.4

Wipers and Washers - Windshield Wiper Motor
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Cowl Vent Screen (501-02 Front End Body Panels, Removal and Installation).


3. CAUTION: Tighten the bolts in the sequence shown.


NOTE: LHD illustration shown, RHD is similar.

Torque: 12 Nm










4. NOTE: LHD illustration shown, RHD is similar.
5. NOTE: LHD illustration shown, RHD is similar.

Roof opening panel frame retaining bolts 9 — 80 Roof opening panel motor retaining bolts 4 — 35 Roof opening panel glass retaining screws 4 — 35

Radiator splash shield outer retaining bolts 3 - 26 Radiator splash shield inner retaining bolts 7 - 62 Radiator splash shield inner retaining screws 2 - 18 Front bumper cover retaining bolts 2 - 18 Rear bumper cover retaining bolts 7 - 62 Rear bumper retaining bolts 25 18 - www.JagDocs.com

Bumpers - Front Bumper
Removal and Installation Published: 11-May-2011

Removal

1. The front bumper is serviced as a separate bolt-on panel.














2. The front bumper is replaced in conjunction with:
Front bumper cover


3. WARNING: The hood and its associated components form part of the
pedestrian protection system, it is essential that any repair or
replacement operations do not affect the safe working of the system.

For additional information relating to the pedestrian safety system
please see the following:
For additional information, refer to: Pedestrian Protection System (501-20C Pedestrian Protection System, Description and Operation).

4. For additional information relating to this repair procedure please see
the following:
For additional information, refer to: Health and Safety Precautions (100-00 General Information, Description and Operation) /
Body Repairs (501-25A Body Repairs - General Information, Description and Operation) /
Corrosion Protection (501-25B Body Repairs - Corrosion Protection, Description and Operation) /
Body and Frame (501-26 Body Repairs - Vehicle Specific Information and Tolerance Checks, Description and Operation).

5. Disconnect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

6. Remove the front bumper cover.
For additional information, refer to: Front Bumper Cover (501-19 Bumpers, Removal and Installation).

7. Release and position the front bumper wiring harness and the hood
release cable to one side.

Bumpers - Front Bumper Cover
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011


1. WARNING: Make sure to support the vehicle with axle stands.

Raise and support the vehicle.

2. Torque: 3 Nm 3. Torque:
Retaining screws 2 Nm Retaining bolts 7 Nm

Front safety belt retractor to seat track retaining bolt 40 30 - Front safety belt retractor retaining bolt 40 30 - Front safety belt D loop retaining bolt 40 30 - Front safety belt buckle retaining bolt 40 30 - Front safety belt shoulder height adjuster retaining bolts 25 18 - Rear centre safety belt retractor retaining bolts 40 30 - Rear safety belt long end retaining bolts 40 30 - Rear safety belt D loop retaining bolt 40 30 - Rear safety belt long end retaining bolt 40 30 - Rear safety belt buckle retaining bolts 40 30 -