2010 INFINITI QX56 ECU

BCM (BODY CONTROL MODULE)DEF-33
< ECU DIAGNOSIS >
C
DE
F
G H
I
J
K
M A
B
DEF
N
O P
ABLIA0022GB
Revision: April 20092010 QX56

DEF-34
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
Fail Safe
INFOID:0000000005327539
Fail-safe index
BCM performs fail-safe control when any DTC listed below is detected.
ABLIA0023GB
Revision: April 20092010 QX56

BCM (BODY CONTROL MODULE)DEF-35
< ECU DIAGNOSIS >
C
DE
F
G H
I
J
K
M A
B
DEF
N
O P
DTC Inspection Priority ChartINFOID:0000000005327540
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
DTC IndexINFOID:0000000005327541
NOTE: Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni- tion switch OFF → ON again.
• 1 - 39: Displayed if any previous ma lfunction is present when current conditi on is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condi tion if the malfunction is detected again.
Display contents of CONSULT Fail-safe Cancellation
U1000: CAN COMM CIRCUIT I nhibit engine crankingWhen the BCM re-establishes communication with the other mod-
ules.
Priority
DTC
1 • U1000: CAN COMM CIRCUIT
2 • B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2013: STRG COMM 1
• B2552: INTELLIGENT KEY
• B2590: NATS MALFUNCTION
3 • C1729: VHCL SPEED SIG ERR
• C1735: IGNITION SIGNAL
4 • C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1712: [CHECKSUM ERR] FL
• C1713: [CHECKSUM ERR] FR
• C1714: [CHECKSUM ERR] RR
• C1715: [CHECKSUM ERR] RL
• C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1720: [CODE ERR] FL
• C1721: [CODE ERR] FR
• C1722: [CODE ERR] RR
• C1723: [CODE ERR] RL
• C1724: [BATT VOLT LOW] FL
• C1725: [BATT VOLT LOW] FR
• C1726: [BATT VOLT LOW] RR
• C1727: [BATT VOLT LOW] RL
CONSULT display
Fail-safeIntelligent Key
warning lamp ON Tire pressure
monitor warning lamp ON Reference page
No DTC is detected.
further testing
may be required. ————
U1000: CAN COMM CIRCUIT ———BCS-32
B2190: NATS ANTENNA AMP ———SEC-31
Revision: April 20092010 QX56

DEF-36
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
B2191: DIFFERENCE OF KEY———SEC-34
B2192: ID DISCORD BCM-ECM ———SEC-35
B2193: CHAIN OF BCM-ECM ———SEC-37
B2552: INTELLIGENT KEY ———SEC-39
B2590: NATS MALFUNCTION ———SEC-40
C1708: [NO DATA] FL ———WT-14
C1709: [NO DATA] FR ———WT-14
C1710: [NO DATA] RR ———WT-14
C1711: [NO DATA] RL ———WT-14
C1712: [CHECKSUM ERR] FL ———WT-16
C1713: [CHECKSUM ERR] FR ———WT-16
C1714: [CHECKSUM ERR] RR ———WT-16
C1715: [CHECKSUM ERR] RL ———WT-16
C1716: [PRESSDATA ERR] FL ———WT-18
C1717: [PRESSDATA ERR] FR ———WT-18
C1718: [PRESSDATA ERR] RR ———WT-18
C1719: [PRESSDATA ERR] RL ———WT-18
C1720: [CODE ERR] FL ———WT-16
C1721: [CODE ERR] FR ———WT-16
C1722: [CODE ERR] RR ———WT-16
C1723: [CODE ERR] RL ———WT-16
C1724: [BATT VOLT LOW] FL ———WT-16
C1725: [BATT VOLT LOW] FR ———WT-16
C1726: [BATT VOLT LOW] RR ———WT-16
C1727: [BATT VOLT LOW] RL ———WT-16
C1729: VHCL SPEED SIG ERR ———WT-19
C1735: IGNITION SIGNAL ———WT-20
CONSULT display Fail-safeIntelligent Key
warning lamp ON Tire pressure
monitor warning
lamp ON Reference page
Revision: April 20092010 QX56

DLK-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
DE
F
G H
I
J
L
M
SECTION DLK
A
B
DLK
N
O P
CONTENTS
DOOR & LOCK
WITH INTELLIGENT KEY SYSTEM
BASIC INSPECTION ....... .............................
6
DIAGNOSIS AND REPAIR WORKFLOW ..... .....6
Work Flow ........................................................... ......6
INSPECTION AND ADJUSTMENT .....................9
ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL ............................... ......
9
ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL : Description ......
9
ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL : Special Re-
pair Requirement ................................................. ......
9
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT .................................................... ......
9
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ..................................
9
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement .......
9
FUNCTION DIAGNOSIS ..............................10
AUTOMATIC DOOR LOCKS ......................... ....10
System Diagram .................................................. ....10
System Description .................................................10
Component Parts Location ....................................12
Component Description ..........................................12
DOOR LOCK FUNCTION ..................................14
DOOR LOCK AND UNLOCK SWITCH ................. ....14
DOOR LOCK AND UNLOCK SWITCH : System
Diagram ...................................................................
14
DOOR LOCK AND UNLOCK SWITCH : System
Description ..............................................................
14
DOOR LOCK AND UNLOCK SWITCH :
Component Parts Location ....................................
15
DOOR LOCK AND UNLOCK SWITCH :
Component Description ..........................................
15
DOOR REQUEST SWITCH ................................... ....16
DOOR REQUEST SWITCH : System Diagram .......16
DOOR REQUEST SWITCH : System Description ....16
DOOR REQUEST SWITCH :
Component Parts Location ....................................
19
DOOR REQUEST SWITCH :
Component Description ..........................................
21
INTELLIGENT KEY ................................................ ....21
INTELLIGENT KEY : System Diagram ....................21
INTELLIGENT KEY : System Description ...............21
INTELLIGENT KEY : Component Parts Location ....24
INTELLIGENT KEY : Component Description ........25
BACK DOOR OPENER FUNCTION .................27
BACK DOOR OPENER SWITCH .......................... ....27
BACK DOOR OPENER SWITCH : System Dia-
gram ........................................................................
27
BACK DOOR OPENER SWITCH : System De-
scription ...................................................................
27
BACK DOOR OPENER SWITCH :
Component Parts Location ....................................
32
BACK DOOR OPENER SWITCH :
Component Description ..........................................
32
INTELLIGENT KEY ................................................ ....33
INTELLIGENT KEY : System Diagram ....................33
INTELLIGENT KEY : System Description ...............33
INTELLIGENT KEY : Component Parts Location ....35
INTELLIGENT KEY : Component Description ........36
WARNING FUNCTION ......................................38
System Description ..................................................38
Component Parts Location ....................................42
KEY REMINDER FUNCTION ............................44
System Description ..................................................44
Component Parts Location ....................................45
HAZARD AND BUZZER REMINDER FUNC-
TION ..................................................................
47
Revision: April 20092010 QX56

DLK-4
Diagnosis Procedure .............................................138
BACK DOOR CLOSE SWITCH SYSTEM .......139
Diagnosis Procedure ........................................... ..139
BACK DOOR SWITCH ....................................140
Diagnosis Procedure ........................................... ..140
CINCH LATCH MOTOR SYSTEM ...................141
Diagnosis Procedure ........................................... ..141
INTELLIGENT KEY UNIT POWER BACK
DOOR INPUT SIGNAL ....................................
142
Description ........................................................... ..142
Diagnosis Procedure .............................................142
INTELLIGENT KEY UNIT POWER BACK
DOOR OUTPUT SIGNAL ................................
143
Description ........................................................... ..143
Diagnosis Procedure .............................................143
HOMELINK UNIVERSAL TRANSCEIVER ......144
Wiring Diagram .................................................... ..144
Description .............................................................145
Component Function Check ................................146
Diagnosis Procedure .............................................146
ECU DIAGNOSIS ..................................... ..148
BCM (BODY CONTROL MODULE) ............... .148
Reference Value .................................................. ..148
Terminal Layout .....................................................151
Physical Values .....................................................151
Wiring Diagram — POWER DOOR LOCK SYS-
TEM — ..................................................................
157
Fail Safe ................................................................170
DTC Inspection Priority Chart .............................171
DTC Index ........................................................... ..171
INTELLIGENT KEY UNIT ................................173
Reference Value .................................................. ..173
Terminal Layout - Intelligent Key Unit ....................174
Physical Values - Intelligent Key Unit ....................174
Terminal Layout - Steering Lock Solenoid ........... ..177
Physical Values - Steering Lock Solenoid .............177
Wiring Diagram — INTELLIGENT KEY SYSTEM
— ...........................................................................
178
Fail Safe ................................................................195
DTC Inspection Priority Chart .............................196
DTC Index ........................................................... ..196
BACK DOOR CONTROL UNIT .......................197
Reference Value .................................................. ..197
Wiring Diagram—AUTOMATIC BACK DOOR
SYSTEM— ............................................................
199
Fail Safe .............................................................. ..209
SYMPTOM DIAGNOSIS ............................210
INTELLIGENT KEY SYSTEM SYMPTOMS ... .210
Symptom Table ................................................... ..210
DOOR LOCK FUNCTION SYMPTOMS ...........211
DOOR LOCK AND UNLOCK SWITCH .................. .211
DOOR LOCK AND UNLOCK SWITCH : Symptom
Table .....................................................................
211
INTELLIGENT KEY ................................................ .212
INTELLIGENT KEY : Symptom Table ..................212
BACK DOOR OPENER FUNCTION ................214
BACK DOOR OPENER SWITCH .......................... .214
BACK DOOR OPENER SWITCH : Symptom Ta-
ble ........................................................................ .
214
BACK DOOR HANDLE .......................................... .214
BACK DOOR HANDLE : Symptom Table .............215
INTELLIGENT KEY ................................................ .215
INTELLIGENT KEY : Symptom Table ..................215
WARNING FUNCTION SYMPTOMS ...............216
Symptom Table .................................................... .216
KEY REMINDER FUNCTION SYMPTOMS .....219
Symptom Table .................................................... .219
HAZARD FUNCTION ..................................... ..220
Symptom Table .................................................... .220
HORN FUNCTION ............................................221
Symptom Table .................................................... .221
HOMELINK UNIVERSAL TRANSCEIVER ......222
Symptom Table .................................................... .222
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ..............................................................
223
Work Flow ............................................................ .223
Inspection Procedure ............................................225
Diagnostic Worksheet ...........................................227
PRECAUTION ...........................................229
PRECAUTIONS .............................................. ..229
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .............................................................. .
229
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect ................................
229
Precaution for work ...............................................230
PREPARATION .........................................231
PREPARATION .............................................. ..231
Special Service Tool ............................................ .231
Commercial Service Tool ......................................232
ON-VEHICLE REPAIR ..............................233
HOOD ............................................................. ..233
Fitting Adjustment ................................................ .233
Removal and Installation of Hood Assembly ........234
Revision: April 20092010 QX56

DLK-8
< BASIC INSPECTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS AND REPAIR WORKFLOW
The Diagnostic Procedure described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
Is malfunctioning part detected?
YES >> GO TO 8.
NO >> Check voltage of related BCM terminals using CONSULT-III.
8.REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace- ment.
3. Check DTC. If DTC is displayed, erase it.
>> GO TO 9.
9.FINAL CHECK
When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction have been repaired securely.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear?
YES (DTC is detected) >> GO TO 7.
YES (Symptom remains) >> GO TO 6.
NO >> Inspection end
Revision: April 20092010 QX56

DLK-28
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR OPENER FUNCTION
Power Liftgate Switch O
peration (Fully Closed → Fully Open Operation)
• When the power liftgate switch is pressed, back door control unit terminal 23 receives the signal.
• The back door control unit checks the A/T selector lever (P) position through terminal 18, vehicle speed
through terminal 21, ignition status through terminal 7, glass hatch is closed through terminal 17 and battery
voltage is present through terminal 3.
• When the back door control unit receives the signal, if the auto back door operating enable conditions are
met, it sends a 5 volt signal through terminal 6 and grounds terminal 9 to sound the warning chime, sends a
signal to the BCM through terminal 4 to flash the hazard lamps and unlocks the back door latch through ter-
minal 12.
• The back door control unit supplies power to the magnetic clutch and the back door motor and moves the back door in the open direction. (At this time, it also executes speed control, input reverse, and anti-pinch
detection control.)
• When the back door is opened to the full-open position, the full-open position is detected by the encoder, and the back door control unit switches the back door motor OFF and the magnetic clutch is pulsed and then
turned OFF.
• The back door is held in the fully open position by the gas stays.
Remote Keyless Entry Operation (Fully Closed → Fully Open Operation)
• When the keyfob button is pressed for at least 0.5 seconds, back door control unit terminal 21 receives the
signal.
• The back door control unit checks the A/T selector lever (P) position through terminal 18, vehicle speed
through terminal 21, ignition status through terminal 7, glass hatch is closed through terminal 17 and battery
voltage is present through terminal 3.
• When the back door control unit receives the signal, if the auto back door operating enable conditions are
met, it sends a 5 volt signal through terminal 6 and grounds terminal 9 to sound the warning chime, sends a
signal to the BCM through terminal 4 to flash the hazard lamps and unlocks the back door latch through ter-
minal 12.
• The back door control unit supplies power to the magnetic clutch and the back door motor and moves the
back door in the open direction. (At this time, it also executes speed control, input reverse, and anti-pinch
detection control.)
• When the back door is opened to the full-open position, the full-open position is detected by the encoder,
and the back door control unit switches the back door motor OFF and the magnetic clutch is pulsed and then
turned OFF.
• The back door is held in the fully open position by the gas stays.
Back Door Handle Switch Operation (Fully Closed → Fully Open Operation)
• When the back door handle is pulled, back door control unit terminal 26 receives the signal.
• The back door control unit checks that the back door is unlocked and checks the A/T selector lever (P) posi-
tion through terminal 18, vehicle speed through terminal 21, ignition status through terminal 7, glass hatch is
closed, battery voltage and back door close switch position through terminal 13.
• When the back door control unit receives the signal, if all auto back door operating enable conditions are
met, it sends a 5 volt signal through terminal 6 and grounds terminal 9 to sound the warning chime, sends a
signal to the BCM through terminal 4 to flash the hazard lamps and unlocks the back door latch through ter-
minal 12.
• The back door control unit supplies power to the magnetic clutch and the back door motor and moves the
back door in the open direction. (At this time, it also executes speed control, input reverse, and anti-pinch
detection control.)
• When the back door is opened to the full-open position, the full-open position is detected by the encoder,
and the back door control unit switches the back door motor OFF and the magnetic clutch is pulsed and then
turned OFF.
• The back door is held in the fully open position by the gas stays.
Power Liftgate Switch Operation (Fully Open → Fully Closed Operation)
• When the power liftgate switch is pressed, the ba ck door control unit terminal 23 receives the signal.
• The back door control units checks door position through the rotary encoder.
• When the back door control unit receives the signal, if the auto back door operating enable conditions are
met, it sends a signal through terminal 6 and grounds terminal 9 to sound the warning chime and sends a
signal to the BCM through terminal 4 to flash the hazard lamps.
• The back door control unit supplies power to the magnetic clutch and the back door motor and move the back door in the close direction. (At this time, it al so executes speed control, input reverse, and anti-pinch
detection control.)
Revision: April 20092010 QX56