2010 HONDA PILOT Owners Manual

This shows the estimated distance
you can travel on the fuel remaining
in the f uel tank. This distance is
estimated f rom the f uel economy
you received over the last several
miles(U.S.) or kilometers (Canada),
so it will vary with changes in speed,
traf f ic, etc.
This shows the average speed you
are traveling in miles per hour (mph)
forU.S.modelsorkilometersper
hour (km/h) f or Canadian models.
This shows the accumulated
traveling time since you last reset it.
When you turn the ignition switch to
the ON (II) position, ELAPSED
TIME is reset.
You can customize the TRIP A INFO
(Trip A, AVERAGE FUEL A,
ELAPSED TIME A, and AVERAGE
SPEED A) reset condition in the
multi-inf ormation display (see page
).
This shows your vehicle’s average
f uel economy in mpg (U.S. models)
or liter/100 km (Canadian models)
since you last reset Trip A or Trip B.
This shows your instant f uel
economy.
106
RANGE
AVERAGE SPEED A/B
EL A PSED T IME A /BINST A NT FUEL MPG (U.S.
models)/INST A NT FUEL L /100 km
(Canadian models)
AVERAGE FUEL A/B
Multi-Inf ormation Display
Inst rument s and Cont rols
93
——
y

y
(/
yy
2010 Pilot

ÛÝ
ÛÝ
If there is a problem with your
vehicle, f or example the engine oil
level is low or a door is not f ully
closed, the multi-inf ormation display
will show you the problem. It does
this by interrupting the current
display with one or more messages.
The system message(s) triggers the
appropriate indicator(s) on the
instrument panel, including the
system message indicator, to come
on. The system message indicator
does not go of f until the problem(s)
is corrected.
You will also hear a beep when the
system message comes on f or the
first time.
When there are several messages to
be shown, the system switches the
messages every 5 seconds.
The message is shown until you
push the INFO ( or ) button.
To see the message again, press the
INFO ( or ) button, 5 seconds
after the display disappears.
Here is a list of messages shown on
the multi-information display:
Multi-Inf ormation Display
System Messages
94
SYSTEM MESSAGE INDICATOR
——
y
y
(/
yy
2010 Pilot

CONT INUED
See page
13
See page
22
See page
22
See page
35
See page
169
See page
523
See page
523
See page
521
See page
522
See page
521
See page
430
See page
431
See page
79
See page
35
Multi-Inf ormation Display
Inst rument s and Cont rols
95
U.S.
Canada
U.S.
Canada
U.S.
Canada
U.S.
Canada
——
y
y
(/
y
y
2010 Pilot

See page
425
See page
426
See page
426
See page
76
See page
147
See page
412
See page
413
See page
389
See page
477
See page
80
See page
387
See page
128
See page
460
See page
396
See page
137
Multi-Inf ormation Display
96
U.S.
Canada
U.S.
Canada
——
y
y
(/
y

y
2010 Pilot

When the main menu displays
‘‘Keyless Memory Settings ,’’ you
can customize some vehicle control
settings.
To enter the customizing mode,
press the SEL/RESET button.
If you turn the ignition switch to the
ACCESSORY (I) or the LOCK (0)
position, or move the shif t lever out
of Park, the display will change to
the normal screen.
You can customize some vehicle
control settings f or ‘‘DRIVER 1’’ and
‘‘DRIVER 2’’ separately. If ‘‘DRIVER
1’’ or ‘‘DRIVER 2’’ is not displayed,
customizing is not possible.
To have the driver’s ID detected,
make sure your remote transmitter
is linked to the system (see Keyless
Memory Settings on page ).
If you want the settings as they were
when the vehicle lef t the f actory,
select DEFAULT ALL, as described
on page .
Ref er to the table on the f ollowing
pages about the settings you want to
customize.
If you want to change any vehicle
control settings, select CHG
SETTING, then press the SEL/
RESET button.
To change the settings, the ignition
switch must be in the ON (II)
position, and the vehicle must be
stopped with the transmission in
Park.
153
100
CONT INUED
Multi-Inf ormation Display
Customize Settings
Inst rument s and Cont rols
97
TMTM
——
y
y
(/
y
y
2010 Pilot

Î
Î
Î
Î
Î
µ™¶ ™
µ™¶ ™
Î
Menu ItemDescriptionSetting OptionGroup SetupPage
LANGUAGE SELECT ION
ADJUST OUTSIDE
TEMP. DISPLAY
TRIP A INFO RESET
MEMORY POSIT ION LINK
Changes the language used in the display.
Changes the outside temperature reading above or
below its current reading.
Changes the setting of how to reset trip meter A,
average fuel A, elapsed time A, and average speed
A.
Changes the driver’s seat and the outside mirror
positions to a stored setting.
ENGLISH
FRENCH
SPANISH
5°F 0°F 5°F
(U.S.)
3°C 0°C 3°C
(Canada)
with REFUEL
MANUAL ONLY
IGN OFF
ON
OFF
MET ER SET UP
(P.103)
POSITION SETUP
(P.108)
104
105
106
109
: Default setting
Multi-Inf ormation Display
98
——
y
y
(/
y
y
2010 Pilot

Î
Î
Î
Î
Î
Î
Î
Î
Î
Î
Î
Menu ItemDescriptionGroup SetupSetting Option Page
INTERIOR LIGHT
DIMMING T IME
HEADLIGHT
AUTO OFF TIMER
AUTO LIGHT
SENSITIVITY
AUTO DOOR LOCK
AUTO DOOR UNLOCK
KEY AND REMOTE
UNLOCK MODE
KEYLESS LOCK
ACKNOWLEDGMENT
SECURITY RELOCK
TIMER
15 sec
0sec
LOW
MIN
Changes how long (in seconds) the interior lights
stay on after you close the doors and the tailgate.
Changes how long (in seconds) the exterior lights
stay on after you close the driver’s door.
Changes the timing of when the headlights come
on. The headlight switch needs to be in the AUTO
position.
Changes the setting of when to automatically lock
the doors.
Changes the setting of when to automatically
unlock the driver’s/all the doors.
Changes which doors unlock with the remote
transmitter on a first push.
The exterior lights flash each time you press the
LOCK or UNLOCK button. A beeper will also
sound when you press the LOCK button twice.
Changes how long it takes (in seconds) for the
doors to relock and the security system to set after
you unlock but do not open the door.
Set/Cancel all the customized settings as default.
LIGHTING SETUP
(P.110)
DOOR/WINDOW
SETUP
(P.115)
DEFAULT ALL
(P.100)
60 sec
30 sec
60 sec
30 sec
15 sec
MAX
HIGH
MID
SHIFT FROM P
WITH VEH SPEED
OFF
IGN OFF
OFF
DRIVER DOOR
ALL DOORS
ON
OFF
90 sec
60 sec
30 sec
SET
CANCEL
111
112
113
116
117
119
120
121
100
: Default setting
DRIVER DOOR /
AL L DOORS
SHIFT TO P
Multi-Inf ormation Display
Inst rument s and Cont rols
99
——
y
y
(/
y
y
2010 Pilot

ÛÝÛÝ
If you want to set the def ault settings,
press the INFO ( / ) button to
select DEFAULT ALL, then press
the SEL/RESET button.
When DEFAULT ALL is set, you will
see the above display for several
seconds, then the screen returns to
CUSTOMIZE ENTRY.
If the setting is not successf ully
completed, ‘‘FAILED’’ is shown f or
several seconds, and then the screen
goes back to the normal message
mode. Repeat the same procedure to
select DEFAULT ALL.
If you want to cancel DEFAULT
ALL, select CANCEL, then press the
SEL/RESET button. The screen
goes back to the previous display.
To set the def ault settings, press the
INFO ( / ) button to select SET
then press the SEL/RESET button.
DEFAUL T AL L
Multi-Inf ormation Display
100
——
y

y
(/
y
y
2010 Pilot