
Driving and environment
The amount of oil used is related to engine load and speed.
It is normal for the oil consumption of a new engine to reach its
lowest value after a certain mileage has been driven.
You must drive your vehicle about 3,000 mi les (S,000 kilometers)
before you can properly assess oil consumption.
Th is also applies to fuel consumption and engine output .
0 Note
• Have your vehicle maintained properly and in accordance with the
service recommendations in your Warranty
& Maintenance booklet.
Lack of proper maintenance as well as improper use of the vehicle w ill
impair the function of the emission control system and could lead to
damage.
• Do not alter or remove any component of the Emission Control
System unless approved by the manufacturer.
• Do not a lter or remove any device, such as heat shields, switches,
ignition wires, valves, which are designed to protect your vehicle's Emission Contro l System and other important vehicle components .•
Fewer short trips
Fuel consumption will always be relatively high on short
trips .
-Try to avoid driving short distances with a cold engine.
The engine and catalytic converter have to reach their optimal oper·
ating temperature
to reduce fuel consumption and noxious emis
sions effectively.
Just after starting, a cold engine in a mid-size car only achieves a fuel
economy of 6-8 m iles per gallon (30-40 l/100 km) . After about a half
a mile, fuel economy climbs to 12 mpg (20 l/100 km). After about
2.5 mi les (4 km), the engine is at its proper operat ing temperature and fuel economy has reached a normal
level. So you can see that you
should avoid short trips whenever possible .
The
outside temperature is also crit ical in this regard . Your car
consumes more fue l in the winter than in the summer. •

Trailer towing
"-------------------------------------------------
Trailer load distribution
Be sure the load in the trailer is held securely in pla ce to prevent it
from shifting forward, backward or s ideways.
Never allow a passenger to ride in a trailer => & in "Driving instruc
tions" on
page 256.
Engine cooling system
Towing a trailer makes the eng ine work harde r. It is important that
the cooling system's performance is up to the additional load. Make
sure that the cooling system has enough fluid.
Tire pressure
When towing a trailer, inflate the tires of your vehicle to the cold tire
pressure listed under "Full load" on the label located either on the
dr iver's side B-pillar (visible when the door is open) or inside the fuel
filler flap . Inflate trailer tires to trailer and tire manufacturers' spec
ifications.
Lights
The headl ight settings should be checked w ith the trailer attached
before driving off. Check to make sure both vehicle and trai ler lights
are working properly.
Safety chains
Be sure trailer safety cha ins are properly connected from the trailer
to the hitch on the vehicle. Leave enough s lack in the chains to permit
turning corners. When you install safety chains, make sure they will
not drag on the road when you are driving.
T he chains should cross under the trailer tongue to p revent it from
dropping in case of separation from the hitch.
Driving instruct!ons
Driving with a trailer always requires extra care and
consideration.
To obtain the best possible handling of vehicle and trailer,
please note the following:
- Do not tow a loaded trailer when your car itself is not
loaded.
- Be especially careful when passing other veh icles .
- Observe speed limits.
- Do not drive at the maximum permissible speed.
- Always apply brakes early.
- Monitor the temperature gauge .
Weight distribution
Towing a loaded trailer w ith an empty car results in a highly unstable
distr ibution of weight. If this cannot be avoided, drive at very low
speeds only to avo id the r isk of losing steer ing control.
A "balanced" rig is easier to operate and control. Th is means that the
tow vehicle should be loaded to the extent possible and permissible,
wh ile keeping the trailer as light as possible under the c ircumstances.
Whenever possible, trans fer some cargo to the luggage compart
ment of the tow vehicle while observing tongue load requirements
and vehicle loading considerations.
Speed
Th e higher the speed, the more difficult it becomes for the driver to
control the r ig . Do not drive at the maximum permiss ible speed.
Reduce your speed even more if load, weather or wind conditions are
unfavorable -part icularly when go ing downhill.
Reduce vehicle speed
immediately i f the trailer shows the slightest
sign of swaying.
Do not try to stop the swaying by accelerating. _,

-~_C_ le_ a_n_ i_ n_ g=- a_ n_d___. p_ ro_ t_e _c_ t_ i_o _n ___________________________________________ _
Cleaning and protection
General information
Regular care preserves vehicl e val ue.
Any automobile is exposed to industria l fumes, co rrosive road salt,
m ud dy dog fee t, e tc. A well c ared for Audi can look like new many
years after p urchase . Regular and correct care will contribute to
m aint aining the bea uty and val ue of your Audi.
Furthermore, good care may be a condition for substantiating a
warranty claim should corrosion damage or paint defects occur.
Y ou r au thor ized Audi d eale r h as a var iety of dedicated vehicle-care
products
and can advise w hich ones to use for clea ning the exterior
a n d inter io r of your ve hicle.
W het her you use products recommended by Aud i or o ther comme r
cia lly availab le cleaning agents , please ma ke sure yo u appl y them
co rrectly .
& WARNING
• Cleaning agents may be poisonous . Keep them out of the reach
of children.
• Heed all caution labels .
• Always read directions on the container before using any
product. Follow the directions carefully.
• Most chemical cleaners are concentrated and have to be
diluted .
• Use spot removing fluids only in well ventilated areas.
• Do not use gasoline, kero sene , diesel fuel , nail polish remover
or other volatile fluids . They may be toxic, flammable or
hazardous in other ways. Do not wash, wax or dry the vehicle with
the ign ition on or the engine running.
& WARNING (co ntinued)
• Do not clean the under sides of chassi s, fenders , wheel covers,
etc. without protecting your hands and arms. You may cut your
self on sharp-edged metal parts.
• Moisture and ice on brakes may impair braking efficiency
~ page 243, "General information ". Test the brakes carefully
each time you wash the vehicle .
'£> For the sake of the environment
Select only envir onmenta lly fr iendly clea ning produc ts . Leftover
cleaning pro ducts sho uld not dis posed of i n the household waste .•
Care of exterior
Washing
F re qu ent w ashin g protec ts th e vehicl e.
T he best protection aga inst env ironmental influences is frequent
w ashi ng and w ax ing. How o ften t his is requ ired depen ds on:
• How m uch the vehicle is use d
• Whe re the ve hicle is parke d (gar age, in the o pen un der tr ees, e tc.)
• The seasona l and weather conditions
• E nviron mental influences
T he longer bi rd droppings , insects , tree resin, road and industria l
gr ime, t ar, soo t, road sa lt and o ther ma ter ia ls remain on the veh icle
body, the more lasti ng their destructive effects w ill be. H igh temper
atu res cause d by ex pos ure to intense s unlight int ensify the co rrosive
effect, part icu larly when humid ity is high as we ll.
~

-~_C_ le_ a_n_ i_ n_ g=- a_ n_d___. p_ ro_ t_e _c_ t_ i_o _n ___________________________________________ _
& WARNING (conti nu ed )
• Alway s read and heed all WARNINGS and other information
~ page 260 .
0 Note
• N ever try to remove dirt, mud o r d ust if the su rface of the vehicle
is dry . Never use a dry cloth or sponge, since this could scratch your
veh icle's pai nt or windows.
• Never was h your car in bright sunlight . D rops of water act as
magni fyi ng lenses and may damage your pa int.
• When you was h yo ur c ar in the winter: i f you rinse your vehicle wit h
a hose, be care ful not to a im the stream of wate r d irectly at locks, or
at door or hatch openings -they can freeze shut.
• Never use sponges des igned to remove insects, or any kitchen
s co ur ing sponges or s imilar pro ducts. They can damage your paint
fin ish ,
• You shou ld remove debris (s uch as inse cts) from the he adlight
lenses on a regu lar bas is, for example when refuelling yo ur vehicle .
• N ever use a d ry cl oth o r sponge to clean t he he adlig hts . Only use
wet cloths or sponges to prevent scratches. It is best to use soapy
wate r.
~ For the sake of the environment
In the in terest o f th e envi ronme nt, the ve hicl e should o nly be washed
in special wash bays. •
Washing your vehicle with a power washer
Clea ning the ex teri or of y our c ar with a high- pre ssu re
po wer washer is safe as long as y ou obser ve a fe w sim ple
rul es.
- Before using the powe r washer, make su re you have read
a nd unders tood the WARN IN GS=>
& in "General info r
ma tio n" on
page 260.
- Alw ays fo llow t he operat ing i nst ructions fo r the powe r
washer.
- Make sure t hat the jet o n the spray hose produces a "fa n
shaped sp ray".
- Do
not ho ld t he spr ay no zz le too close t o sof t ma terials .
Never use a power wa sher to cl ean the powe r to p itself.
When cleaning the vehicle with a powe r washe r
always follow the
operat ing inst ruct ions . T his app lies part icu larly to the
operating
pres sure
and the spraying distance. M ain tain a suff ic ient distance to
soft mater ia ls s uch as rubbe r hoses an d so und/v ibration deaden ing
m ater ials (pa rt icula rly on t he un derside o f th e e ng ine hood). Do not
use a jet which sprays water in a
direct stream or one that has a
rotating j et.
Water temperature s hou ld not exceed 140
°F (60 °().
& WARNING
Never wash tires with a jet that sprays water in a direct stream.
This could cause invisible damage to the tires and weaken them ,
even if the spray is from a relatively long distance and for a short
time . Damaged and weakened tires can fail and cause accident s
and personal injury . .,_

-Cleaning and protection pn, _____________________ _
0 Note
• Never use chemical so lvents (e.g. lig hte r fluid, turpentine), waxes,
shoe po lish or simi lar p roducts on Alca ntara ® surfaces .
• To avo id damage, have stubborn stains removed by a commerc ia l
cleaning specialist .
• Do not use brushes, stiff sponges or sim ila rly abrasive cleaning
aids. •
Safety belts
Only well-maintain ed safety belts work reliably when
needed .
-Keep be lts clea n.
- For cleani ng, use a mi ld soap and wa ter solution. Let be lts
d ry thoroug hly and away fro m dir ect sun light.
- Do not allow in ertia re el s afety b elts to ret ra ct bef ore t hey
are comp le tel y dry .
- C heck the condi tion of y our safety bel ts
regularly .
Heavily soiled safety belts may no t re tract p roper ly .
& WARNING
Damaged safety belts can break in a crash.
• Anything that might damage your safety belts could mean
that you and your passengers would not be adequately protected
in an a ccident.
• Safety belt performance depends on correct installation. Never
remove belts from the vehicle to clean them.
• Do not use chemical cleaning agents , bleach or dyes. They have
corro sive properties which weaken the webbing .
& WARNING (c on tinued )
• When cleaning your safety belts , inspect them for damage. If
you discover damage , see your authorized Audi d ealer .
• Always read and heed all WARNINGS and other info rmation
=:> page 260 . •
Engine compartment
B e especi ally care ful w hen cleaning the engine comp art
men t.
Always switch off the ignition before cleaning the engine=>& .
Plenum panel
Remove leaves from the plenum panel in front of the windsh ield
un der th e eng ine hoo d. This p revents the wate r drain holes from
becom ing b locked, and it prevents debris from entering the ve hicle
inter io r thr ough the heat ing and ventila tion ducts.
Corrosion protection
Th e engine compartment and tran smission have been cor rosion
protected at the factory.
Goo d an ti- cor ros ion treatmen t is very impo rtan t, pa rtic ula rly in the
w inte r. If the vehicle is frequently driven on sa lt treated roads, t he
entire eng ine compa rtment and plenum pane l sho uld be thoroug hly
cleaned at the end of w inter and retreated to prevent sa lt damage . At
the same time, the underside of the vehicle should be washed as we ll.
If the eng ine co m par tment is clea ned at any time wi th grease
removing solutions
2l, or if you have the engine washed, the anti
c o rrosion treatment is a lmost always remove d as we ll.
It is the refore
essential to have a long-last ing corrosion protect io n reapplied to all
s u rfaces, seams, joints and components in the engine compartmen t. ~
2
l Use on ly the co rrect clean ing so lut ions . Neve r use gaso line or d iese l fuel.

Fuel supply and filling your fuel tank
Fuel supply and filling your fuel tank
Gasoline
Fuel supply
Using the right fuel helps keep the environment clean and
prevents engine damage.
Fuel recommendation
The f ue l recommended for yo ur vehicle is unleaded premium grade
gasoline. See also=>
page 342, "D at a". Aud i recommends using TO P
TIER Detergent Gasoline with a m inimum octane rating of 91 AKI (9S
R ON ). For more inform ation on TOP TIE R De tergent Gasoline, please
go to the official website (www .topt iergas .com) .
Th e recommended gasoline octane rating for your engine can a lso be
found on a labe l located o n the i nside of t he fue l fille r flap. This rating
may be specified as AKI o r RON .
Yo ur vehicle may a lso be opera ted u sing unle aded reg ula r gaso line
w ith a minim um octane rating of 87 AKI/91 RON. However, using 87
AKI/91 RON octane fue l will slig htly reduce engi ne pe rformance.
Use unleaded gasoline only . Unleaded gaso line is available
througho ut the USA, Canada, and in most E uropean countries. We
recommend tha t you do not take your ve hicl e to a reas or countries
where unleaded gasoline may not be availab le.
For mo re in format io n on refueling your vehi cle, see =>
page 275 .
Octane rating
Octane r atin g indica tes a gaso line's ability to resis t eng ine dam ag ing
"knock" caused by premature ignition and detonatio n. Therefore,
buying the co rr ec t gr ade o f gas oline is very im port an t to help prevent
poss ible engine damage and a loss of engi ne performance .
Gaso line most common ly used in the United States and Canada has
the following octa ne rat ings that can usually be fou nd on the filler
pump: •
Premium Grade : 9 1 -96 AKI
• Regu lar Grade: 87 - 90 AKI
E xp lanation o f the a bbrev iations:
AKI= Anti Knock Index= (R +M)/2 = (RON+MON)/2
RON= Resea rch Octane Number
M ON= M otor Octane Number.
(D Note
• Do not use any f uel w ith oc tane ra tings lower than 87 AKI or 91
RO N othe rw ise ex pensive engine damage will occu r.
• Do
not use leade d gasoline. The use of leaded gasoline w ill
severely damage you r vehicle's catalytic co nve rter and i ts ab ility to
control exhaust emissions.•
Blended gasoline
Use of gasoline containing alcohol or MTBE (methyl
tertiary butyl ether)
You may use unleade d gasoline blended w ith alcoho l or M TBE
( c ommon ly refe rred to as oxygenates) if the blen ded mixture meets
the fo llowing c riter ia:
Blend of g asoline methanol (wood alcohol or methyl alcohol)
• Anti -k nock inde x must be 87 AKI or higher.
• B lend must con tain no mo re t han 3% met hano l.
• Blend must contain more than 2% co-solvents.
Blend of gasoline and ethanol (grain alcohol or ethyl alcohol)
• Anti- knock index must be 87 AKI o r higher.
• B lend must no t conta in mo re than 10% e thanol.

Fuel supply and filling your fuel tank Ill --------------'--':.......::-----=--=--------
Blend of gasoline and MTBE
• Anti-knock index must be 87 AKI or higher.
• Blend must contain not more than 15% MTBE.
Seasonally adjusted gasoline
Many gasoline grades are blended to perform especially well for
winter or summer driving. During seasonal change-over, we suggest
that you fill up at busy gas stations where the seasonal adjustment is
more likely to be made in time.
0 Note
• Methanol fuels which do not meet these requirements may cause
corros ion and damage to plastic and rubber components in the fue l
system .
• Do not use fuels that fail to meet the specified criteria in this
chapter.
• If you are unab le to determine whether or not a particu lar fuel
blend meets the specifications, ask your service station or its fuel
s u pplier.
• Do not use fue l for which the contents cannot be identified.
• Fuel system damage and performance problems resulting from
the use of fuels different from those specified are not the responsi
bility of Audi and are not covered under the New Vehicle or the Emis
sion Control System Warranties.
• If you experience a loss of fuel economy or driveability and perfor
mance problems due to the use of one of these fuel blends, we
recommend that you switch to unblended f uel. •
Gasoline additives
A major concern among many auto manufacturers is carbon depos it
build -up caused by the type of gasoline you use.
Safety first
Although gasoline grades differ from one manufacturer to another,
t hey have certain things in common. All gasoline grades contain
substances that can cause depos its to collect on v ital engi ne parts,
such as fuel injectors and intake valves. Although most gasoline
brands include additives to keep engine and fuel systems clean, they
are not equally effective .
Audi recommends using TOP TIER Detergent Gasoline. For more
information on TOP TIER Detergent Gasoline, please go to the officia l
webs ite (www.toptiergas.com).
After an extended per iod of using inadequate fuels, built-up carbon
deposits can rob your engine of peak performance .
0 Note
Damage or malfunction due to poor fuel quality is not covered by the
Audi New Vehicle Limited Warranty. •
Fuel tank
Fuel filler neck
The fue l filler neck is located on the right rear side panel behind the
fue l filler flap .
If the power locking system should fai l, you can sti ll open the flap
ma nually- for detailed instructions see:::::>
page 278.
You can find the fuel tank capacity of your vehicle in Technical Data
:::::, page 342.
The label on the inside of the fuel filler flap tells you the correct fuel
for your vehicle. For more information about fuel specifications, see
:::::>
page 2 7 4 .
Your vehicle fuel tank has an on -board refuelling vapor recovery
system. This feature helps to prevent fuel vapors from escaping from
the tank and pollut ing the environment while you refuel your vehicle . .,,_
Vehicle care Technical data

Fuel supply and filling your fuel tank
In order to fill the tank properly while protecting the environment,
please follow this refueling procedure carefully.
& WARNING
Under normal operating conditions, never carry additional fuel
containers in your car. Gas canisters and other containers used to
transport fuel can be dangerous. Such containers, full or empty,
may leak and could cause a fire in a collision. If you must transport
fuel to use for your lawn mower, snow blower, etc., be very careful
and always observe local and state laws regarding the use, trans
portation and storage of such fuel containers. Make certain the
container meets industry standards (ANSI/ASTM F852 -86).
0 Note
Never drive your vehicle until the fuel tank is completely empty . The
irregular supply of fuel can cause misfiring. Gasoline could enter the
exhaust system and damage the catalytic converter. •
Refuelling
-
Fig. 215 Right rear
veh icle side: Opening
the fuel filler flap Fig
. 216 Fuel filler
flap with attached fuel cap
When activating the central locking, the fuel filler flap is
automatically unlocked or locked. Refuel the vehicle with the
ignition turned
off.
Taking the fuel cap off
- Turn off the ignition.
- Press the left side of the fuel filler flap to open it
~ fig. 215 -arrow-.
- Unscr ew fuel cap counter-clockwise and hang it on the fuel
filler flap~ fig. 216.
Refuelling procedure
- Ins ert the fuel nozzle from the gasoline pump into the
fuel filler neck as far as it will go.
- Select a medium refuelling rate so that the nozzle switches off automatically when the tank is full.
Putting the fuel cap back on
- After filling your tank, twist the fuel cap clockwise as far
as it will go.
- Close the fuel filler flap. .,