2009 SUBARU TRIBECA oil filter

5AT-55
ATF Filter
AUTOMATIC TRANSMISSION
18.ATF Filter
A: REMOVAL
1) Remove the front bumper. MOVAL, Front Bumper.>
2) Using the ST, remove the ATF filter.
ST 498545400 OIL FILTER WRENCH
B: INSTALLATION
1) Apply a thin coat of ATF to the oil seal part of
new ATF filter.
2) Install the ATF filter. Turn it by hand, being care-
ful not to damage oil seal.
3) Tighten the ATF filter using ST.
Calculate the ATF filter tightening torque using fol-
lowing formula.
T2 = L2/(L1 + L2) × T1
T1: 14 N·m (1.4 kgf-m, 10.1 ft-lb)
[Required torque setting]
T2: Tightening torque
L1: ST length 78 mm (3.07 in)
L2: Torque wrench length
Example:
NOTE:
Align the ST with the torque wrench while tighten-
ing the ATF filter.
ST 498545400 OIL FILTER WRENCH
4) Fill ATF.
5) Inspect the level of ATF. matic Transmission Fluid.>
6) Install the front bumper. LATION, Front Bumper.>
C: INSPECTION
Check for rust, hole, ATF leaks or other damage.
Replace the part if any damage is found in the in-
spection.
To r q u e w r e n c h l e n g t h
mm (in)
Tightening torque
N·m (kgf-m, ft-lb)
100 (3.94) 7.7 (0.79, 5.7)
150 (5.91) 9.0 (0.92, 6.7)
200 (7.87) 10 (1.0, 7.4)
AT-03251

5AT-58
ATF Cooler Pipe & Hose
AUTOMATIC TRANSMISSION
10) Remove the oil cooler inlet and outlet pipes.
NOTE:
When disconnecting the outlet pipe, be careful not
to lose the ball and spring used with retaining
screw.
B: INSTALLATION
1) Install the oil cooler inlet and outlet pipes with
new washer.
Tightening torque:
T1: 40 N·m (4.1 kgf-m, 29.5 ft-lb)
T2: 41 N·m (4.2 kgf-m, 30.4 ft-lb)
T3: 45 N·m (4.6 kgf-m, 33.2 ft-lb)
2) Install the ATF cooler pipe to frame.
3) Attach the bolts securing the ATF cooler pipe,
and attach the ATF cooler hose.
4) Attach the ATF filter inlet and outlet hoses.
5) Install the front bumper. LATION, Front Bumper.>
(A) Outlet pipe
(B) Inlet pipe
AT-01383
(A)
(B)
AT-03133
T2
T1 T2
T3
AT-01347
AT-03263
AT-03262

5AT-75
Converter Case
AUTOMATIC TRANSMISSION
30.Converter Case
A: REMOVAL
1) Remove the transmission assembly from vehicle
body. Transmission Assembly.>
2) Remove the torque converter assembly. 5AT-62, REMOVAL, Torque Converter Assembly.>
3) Remove the transmission harness connector
from stay.
4) Remove the turbine speed sensor 1. 5AT-52, REMOVAL, Turbine Speed Sensor 1.>
5) Remove the oil charge pipe. REMOVAL, Oil Charge Pipe.>
6) Remove the ATF filter inlet and outlet pipes.
Hose.>
7) Remove the converter case attachment bolts.
8) Lay along the transmission body, and then re-
move the oil pan.
9) Remove the three converter case mounting bolts
(TORX®).
ST 18676AA020 TORX® WRENCH
10) Separate the converter case by lightly tapping
with plastic hammer.
11) Remove the differential assembly. 5AT-86, REMOVAL, Front Differential Assembly.>
12) Remove the oil seal from converter case.
B: INSTALLATION
1) Check the appearance of each component and
clean them.
2) Press-fit the oil seal to converter case using ST.
ST 499587100 OIL SEAL INSTALLER
3) Install the differential assembly to the case.
tial Assembly.>
4) Install the right and left side retainers. 5AT-89, ADJUSTMENT, Front Differential Assem-
bly.>
5) Apply proper amount of liquid gasket to the en-
tire matching surface of converter case.
Liquid gasket:
THREE BOND 1215 (Part No. 004403007)
6) Install the converter case assembly without
damaging bushing and oil seal.
Tightening torque:
41 N·m (4.2 kgf-m, 30.4 ft-lb)
AT-01974
AT-01979
ST
AT-01975

5AT-76
Converter Case
AUTOMATIC TRANSMISSION
7) Install the three converter case mounting bolts
(TORX®).
ST 18676AA020 TORX® WRENCH
Tightening torque:
41 N·m (4.2 kgf-m, 30.4 ft-lb)
8) Apply proper amount of liquid gasket to the en-
tire oil pan mating surface, and then install it.
Liquid gasket:
THREE BOND 1217B (Part No. K0877YA020)
Tightening torque:
5 N·m (0.5 kgf-m, 3.7 ft-lb)
9) Install the transmission harness connector to the
stay.
10) Install the air breather hose. INSTALLATION, Air Breather Hose.>
11) Install the ATF filter pipe. STALLATION, ATF Cooler Pipe & Hose.>
12) Install the oil charge pipe with O-ring. 5AT-61, INSTALLATION, Oil Charge Pipe.>
13) Install the torque converter assembly. 5AT-62, INSTALLATION, Torque Converter As-
sembly.>
14) Install the transmission assembly to the vehi-
cle. Transmission Assembly.>
C: INSPECTION
Measure the backlash, and then adjust it to be with-
in standard values. MENT, Drive Pinion Shaft Assembly.>
AT-01974
AT-03249

5AT-77
Oil Pump Cover
AUTOMATIC TRANSMISSION
31.Oil Pump Cover
A: REMOVAL
1) Remove the transmission assembly from vehicle
body. Transmission Assembly.>
2) Pull out the torque converter assembly. 5AT-62, REMOVAL, Torque Converter Assembly.>
3) Remove the transmission harness connector
from stay.
4) Remove the oil charge pipe. REMOVAL, Oil Charge Pipe.>
5) Remove the ATF filter inlet and outlet pipes.
Hose.>
6) Separate the converter case and transmission
case. Case.>
7) Remove the oil pump cover mounting bolt, and
then separate the oil pump cover from the AT main
case by lightly tapping with plastic hammer.
B: INSTALLATION
1) Secure the oil pump cover.
Tightening torque:
41 N·m (4.2 kgf-m, 30.4 ft-lb)
2) Install the converter case assembly to the trans-
mission case assembly. LATION, Torque Converter Assembly.>
3) Install the transmission harness connector to the
stay.
4) Install the ATF filter pipe. STALLATION, ATF Cooler Pipe & Hose.>
5) Install the oil charge pipe together with an O-
ring. Pipe.>
6) Install the torque converter assembly. 5AT-62, INSTALLATION, Torque Converter As-
sembly.>
7) Install the transmission assembly to the vehicle.
Transmission Assembly.>
C: DISASSEMBLY
1. FRONT BRAKE
1) Remove the snap ring.
2) Remove the retainer plate, drive plate and driven
plate.
AT-01976
AT-01976
AT-01980

5AT-81
Drive Pinion Shaft Assembly
AUTOMATIC TRANSMISSION
32.Drive Pinion Shaft Assembly
A: REMOVAL
1) Remove the transmission assembly from vehicle
body. Transmission Assembly.>
2) Pull out the torque converter assembly. 5AT-62, REMOVAL, Torque Converter Assembly.>
3) Remove the transmission harness connector
from stay.
4) Disconnect the air breather hose. 60, REMOVAL, Air Breather Hose.>
5) Remove the oil charge pipe. REMOVAL, Oil Charge Pipe.>
6) Remove the ATF filter inlet and outlet pipes.
Hose.>
7) Separate the converter case and transmission
case. Case.>
8) Remove the drive pinion shaft mounting bolts,
and then remove the drive pinion shaft assembly
from oil pump cover.
9) Remove the oil pump cover from AT main case.

B: INSTALLATION
1) Assemble the drive pinion assembly to oil pump
cover.
NOTE:
Be careful not to bend the shim.
Tightening torque:
70 N·m (7.1 kgf-m, 51.6 ft-lb)
2) Adjust the tooth contact between drive pinion
shaft assembly and the front differential side gear.
Shaft Assembly.>
3) Join the converter case with the transmission
case. Case.>
4) Install the transmission harness connector to the
stay.
5) Install the ATF filter pipe. STALLATION, ATF Cooler Pipe & Hose.>
6) Install the oil charge pipe with O-ring.
7) Install the torque converter assembly. 5AT-62, INSTALLATION, Torque Converter As-
sembly.>
8) Install the transmission assembly to the vehicle.
Transmission Assembly.>
C: DISASSEMBLY
1) Remove the crimped part of the lock nut, and
then remove the lock nut while holding the rear
spline part of the shaft using ST1 and ST2. Pull out
the drive pinion collar.
ST1 18667AA010 HOLDER
ST2 499787700 WRENCH
ST3 499787500 ADAPTER
2) Remove the O-ring.
3) Separate the roller bearing and outer race from
shaft using a press.
AT-01984
AT-01984
(A) Outer race
AT-00197
ST1
ST3
ST2
AT-00198
(A)

5AT-86
Front Differential Assembly
AUTOMATIC TRANSMISSION
33.Front Differential Assembly
A: REMOVAL
1) Remove the transmission assembly from vehicle
body. Transmission Assembly.>
2) Pull out the torque converter assembly. 5AT-62, REMOVAL, Torque Converter Assembly.>
3) Remove the transmission harness connector
from stay.
4) Remove the oil charge pipe. REMOVAL, Oil Charge Pipe.>
5) Remove the ATF filter inlet and outlet pipes.
Hose.>
6) Separate the converter case from the transmis-
sion case. Case.>
7) Remove the differential side retainers using ST.
NOTE:
Hold the differential case assembly by hand to
avoid damaging the retainer mounting hole of the
converter case.
ST 18630AA010 WRENCH COMPL RETAIN-
ER
8) Remove the differential assembly while being
careful not to damage the attachment part of retain-
er.
B: INSTALLATION
1) When installing the differential assembly to
case, be careful not to damage the inside of case
(particularly, the differential side retainer mating
surface).
2) Install the O-ring to left and right side retainer.
3) Using the ST, install the side retainer. 5AT-86, REMOVAL, Front Differential Assembly.>
ST 18630AA010 WRENCH COMPL RETAIN-
ER
4) Adjust the backlash of the front differential. to 5AT-89, ADJUSTMENT, Front Differential As-
sembly.>
5) Install the lock plate.
Tightening torque:
25 N·m (2.5 kgf-m, 18 ft-lb)
6) Install the converter case to the transmission
case. Case.>
7) Install the transmission harness connector to the
stay.
8) Install the ATF filter pipe. STALLATION, ATF Cooler Pipe & Hose.>
9) Install the oil charge pipe together with an O-
ring. Pipe.>
10) Install the torque converter assembly. 5AT-62, INSTALLATION, Torque Converter As-
sembly.>
11) Install the transmission assembly to the vehi-
cle. Transmission Assembly.>
C: DISASSEMBLY
1. DIFFERENTIAL CASE ASSEMBLY
1) Remove the taper roller bearing using the ST
and a press.
ST 498077000 REMOVER
(A) Differential ASSY
AT-01987
(A)
(A) Lock plate
AT-01988
(A)
AT-00216

5AT-91
AT Main Case
AUTOMATIC TRANSMISSION
34.AT Main Case
A: REMOVAL
1) Remove the transmission assembly from vehicle
body. Transmission Assembly.>
2) Pull out the torque converter assembly. 5AT-62, REMOVAL, Torque Converter Assembly.>
3) Remove the transmission harness connector
from stay.
4) Disconnect the air breather hose.
5) Remove the oil charge pipe. REMOVAL, Oil Charge Pipe.>
6) Remove the ATF filter inlet and outlet pipes.
Hose.>
7) Remove the extension case. REMOVAL, Extension Case.>
8) Remove the center differential carrier. 5AT-71, REMOVAL, Center Differential Carrier.>
9) Remove the reduction driven gear. 68, REMOVAL, Reduction Driven Gear.>
10) Separate the converter case from the transmis-
sion case. Case.>
11) Remove the control valve body. 53, REMOVAL, Control Valve Body.>
12) Remove the oil pump cover.

NOTE:
The input clutch pack assembly and front sun gear
assembly are also removed together.
13) Remove the needle bearing of the middle carri-
er assembly.
14) Remove the middle carrier assembly.
15) Remove the rear carrier assembly.
AT-01990
AT-01991
AT-01992
AT-01993