2009 SUBARU TRIBECA Harness

SL-37
Front Door Lock Actuator
SECURITY AND LOCKS
8. Front Door Lock Actuator
A: REMOVAL
1) Remove the front door latch and door lock actu-
ator assembly. Door Latch and Door Lock Actuator Assembly.>
2) Remove the pawl of front door latch security cov-
er, and then remove the cover.
3) Remove the screw from front door latch and
door lock actuator, and then remove the door lock
actuator.
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
Make sure lock and unlock works correctly after in-
stallation.
C: INSPECTION
1) Disconnect the door lock actuator harness con-
nector.
2) Connect the battery to door lock actuator termi-
nals.
If defective, replace the door lock actuator.
(1) Front door lock actuator
Te r m i n a l N o . A c t u a t o r o p e r a t i o n
No. 1 (+) and No. 2 (–) Unlock → Lock
No. 2 (+) and No. 1 (–) Lock → Unlock
SL-00444
(1)
SL-00471
1
2

SL-41
Rear Door Lock Actuator
SECURITY AND LOCKS
12.Rear Door Lock Actuator
A: REMOVAL
1) Remove the rear door latch and door lock actu-
ator assembly. Door Latch and Door Lock Actuator Assembly.>
2) Remove the pawl of rear door latch security cov-
er, and then remove the cover.
3) Remove the screw from the rear door latch and
door lock actuator, and then remove the door lock
actuator.
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
Make sure lock and unlock works correctly after in-
stallation.
C: INSPECTION
1) Disconnect the door lock actuator harness con-
nector.
2) Connect the battery to door lock actuator termi-
nals.
If defective, replace the door lock actuator.
(1) Rear door lock actuator
Te r m i n a l N o . A c t u a t o r o p e r a t i o n
No. 1 (+) and No. 2 (–) Unlock → Lock
No. 2 (+) and No. 1 (–) Lock → Unlock
SL-00446
SL-00471
1
2

SL-42
Rear Gate Release Switch
SECURITY AND LOCKS
13.Rear Gate Release Switch
A: REMOVAL
1) Remove the rear gate trim. MOVAL, Rear Gate Trim.>
2) Remove the rear gate garnish. REMOVAL, Rear Gate Garnish.>
3) Disconnect the harness connector of the rear
gate release switch.
4) Hold the rear gate release switch hook, and re-
move the rear gate release switch.
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
Make sure the rear gate latch assembly works after
installation.
C: INSPECTION
1) Disconnect the harness connector of the rear
gate release switch.
2) Inspect the continuity between the rear gate re-
lease switch connector terminals.
If NG, replace the rear gate release switch.
Switch Terminals Standard
OpenNo.1 and No. 2Less than 1 Ω
Close 1 MΩ or more
SL-00458

SL-43
Rear Gate Latch Assembly
SECURITY AND LOCKS
14.Rear Gate Latch Assembly
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the rear gate trim. MOVAL, Rear Gate Trim.>
3) Disconnect the harness connector of rear gate
latch assembly.
4) Remove the two screws.
5) Remove the rear gate latch assembly.
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
Make sure the lock works correctly after installa-
tion.
C: INSPECTION
1) Disconnect the rear gate lock actuator harness
connector.
2) Connect the battery to rear gate lock actuator
terminals.
Replace the rear gate latch assembly if faulty.
Te r m i n a l N o . A c t u a t o r o p e r a t i o n
No. 2 (+) and No. 1 (–) Unlock → Lock
No. 1 (+) and No. 2 (–) Lock → Unlock
SL-00447
SL-00449
21
43

SL-46
Ignition Key Lock
SECURITY AND LOCKS
17.Ignition Key Lock
A: REPLACEMENT
1) Disconnect the ground cable from battery.
2) Remove the steering column. REMOVAL, Tilt Steering Column.>
3) Secure the steering column in a vise. Remove
the bolt with a drill.
4) Remove the ignition key lock.
5) Using a new bolt, tighten the bolts all the way.
B: INSPECTION
1) Remove the instrument panel lower panel.
2) Remove the lower column cover.
3) Unfasten the fixing clip which secures harness,
and then disconnect the connector of the ignition
switch from body harness.
4) Turn the ignition key plate to each position and
check the continuity between terminals of ignition
connector.
If NG, replace the ignition switch.
SL-00024
SL-00025
Switch position Terminal No. Standard
LOCK — —
ACC No. 3 and No. 4 Less than 1 Ω
ON
No. 3, No. 1 and
No. 4
No. 3 and No. 6
Less than 1 Ω
ST
No. 3 and No. 1
No. 3, No. 2 and
No. 6
Less than 1 Ω
SL-00266
13
456
2

SR-4
Sunroof Control System
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
2. Sunroof Control System
A: WIRING DIAGRAM
1. SUNROOF

B: INSPECTION
•Failure turn of glass lid while driving rough road.
Glass lid has auto-reverse function. When applied above specified force to the glass lid, the lid turns back
and stops. When operating the glass lid (open or close) while driving the rough road, the lid judges vibration
as a force and may causes failure turns. When the failure turn is occurred, need to perform the initialize op-
eration with following procedure.
1. INITIALIZE OPERATION
1) Tilt up the glass lid.
2) Release the switch once, and press the tilt up switch again for 15 seconds.
3) When the glass lid is raised a little and returned to tilt up position, release the switch for the moment. (Ini-
tialization of position detecting function)
4) Holding down the tilt up switch again within 5 seconds from releasing the switch will automatically perform
tilt down/slide open/slide close. (When more than 5 seconds pass, the position detecting function is can-
celled.)
5) Initialize operation is completed.
Symptom Inspection order
Wa t er l e ak ag e 1 . Che ck r o o f p a ne l a n d g la ss li d fo r i mp r o pe r or p oo r se al i ng .
2. Check drain tube for clogging.
3. Check sunroof frame seal and body for improper fit.
Booming noise, wind noise and other noise 1. Check glass lid and roof panel for improper clearance.
2. Check sunshade and roof trim for improper clearance.
Abnormal motor noise 1. Check installing part of motor for looseness.
2. Check gears and bearings for wear.
3. Check cable for wear.
4. Check cable pipe for deformities.
Fai l ur e of su n r oo f
(Motor operates properly.)
1. Check guide rail for foreign particles.
2. Check guide rail for improper installation.
3. Check parts for mutual interference.
4. Check cable slider for improper clinching.
5. Check cable for improper installation.
Motor does not rotate or rotate improperly. 1. Check fuse for blown out.
2. Check switch for improper function.
3. Check motor for incorrect terminal voltage.
4. Check the relay for improper operation.
5. Check poor grounding system.
6. Check harness for open or short and terminals for poor connections.
Fai l ur e tu r n o f gl a ss l i d Ch e ck gu i de ra il fo r fo r e ig n p a r ti cl e s.

SR-7
Sunroof Assembly
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
4. Sunroof Assembly
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the roof trim. AL, Roof Trim.>
3) Disconnect the harness connector of sunroof
motor.
4) Remove the glass lid. AL, Glass Lid.>
5) Remove the drain tube from frame assembly.
6) Remove the bolts, and then detach the frame as-
sembly.
B: INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be careful not to snag the harness.
NOTE:
•Be sure to connect the harness connector.
•When installing the drain tube, insert it securely
into drain pipe.
Length A:
15 mm (0.59 in) or more
C: DISASSEMBLY
1) Remove the sunroof motor. MOVAL, Sunroof Motor.>
2) Remove the sunshade. MOVAL, Sunshade.>
D: ASSEMBLY
Assemble in the reverse order of disassembly.
SR-00005
A

SR-8
Sunroof Motor
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
5. Sunroof Motor
A: REMOVAL
CAUTION:
•When removing the clip, use great care not to
damage the roof trim.
•Never rotate the sunroof motor after remov-
ing it.
1) Completely close the glass lid.
2) Disconnect the ground cable from battery.
3) Remove the spot map light. MOVAL, Spot Map Light.>
4) Disconnect the harness connector, and then re-
move the motor assembly mounting screw.
CAUTION:
When removing the motor assembly, secure
the cable wires to prevent moves.
B: INSTALLATION
CAUTION:
When installing the motor assembly, be careful
not to move the sunroof cable.
1) Align the coulisse assembly and link assembly in
the same position.
2) Install the motor assembly.
3) Connect the harness connector of motor assem-
bly, and then connect the battery ground cable to
battery.
4) Perform the initialize operation of motor.
(1) Tilt up the glass lid.
(2) Release the switch once, and press the tilt
up switch again for 15 seconds.
(3) When the glass lid is raised a little and on tilt
up position, release the switch for the moment.
(4) Keep pressing the tilt up switch within 5 sec-
onds from releasing the switch, glass lid auto-
matically performs the tilts down → slides open
→ slides close operation, then the initialize op-
eration is completed.
SR-00121
(1) Front
(2) Coulisse ASSY
(3) Link ASSY
(4) 4.7 mm (0.185 in)
SR-00094
(1)
(3)
(2)(4)