2009 SUBARU TRIBECA roof

AC(diag)-5
General Description
HVAC SYSTEM (AUTO A/C) (DIAGNOSTICS)
4) Inspection of the rear cooler switch
5) Inspection of rear cooler
6) Inspection of illumination control
No. Point to check Switch operation Judgment standard
1FAN switch Turn the FAN switch.
Blower fan switches OFF → LO → ML → MH
→ HI each time turning the switch and it
switches in reverse order when turned back-
ward.
No. Point to check Switch operation Judgment standard
1Roof grill Turn the FAN switch.
Fr on t A / C O N ( co mp r es so r op e rat i ng ) : COOL
Fr on t A / C O FF ( co mp r e ss or n ot o pe ra t in g) :
Blower ON
No. Point to check Switch operation Judgment standard
1Illumination Turn the lighting switch to ON. Illumination comes on.

LI-28
High-mounted Stop Light
LIGHTING SYSTEM
26.High-mounted Stop Light
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Detach the roof spoiler. AL, Roof Spoiler.>
3) Remove the nuts (A), then detach the high-
mounted stop light.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Install the high-mounted stop light to test if it illu-
minates normally.
2) If the high-mounted stop light does not illumi-
nate, replace it with a new one.
NOTE:
Since LEDs (Light Emitting Diodes) are used for
the high-mounted stop light, replace the high-
mounted stop light assembly when the LEDs went
out.
LI-00312
(A)(A)

SB-12
Second Seat Belt
SEAT BELT SYSTEM
6. Second Seat Belt
A: REMOVAL
1. OUTER SEAT BELT RH ASSEMBLY AND
LH ASSEMBLY
1) Remove the second row seats. REMOVAL, Second-row Seats.>
2) Remove the third-row seats. REMOVAL, Third-row Seats.>
3) Remove the rear quarter trim. REMOVAL, Rear Quarter Trim.>
4) Remove the lower anchor bolt.
5) Remove the bolt to remove outer seat belt re-
tractor.
2. SHOULDER SEAT BELT CENTER AS-
SEMBLY
1) Remove the rear quarter trim. REMOVAL, Rear Quarter Trim.>
2) Remove the cover (A) from roof trim, and then
insert it to the inside of roof trim.
3) Remove the clips, and then lower the roof trim
end.
CAUTION:
When removing the roof trim clip, do not pull
the roof trim end backward with excessive
force, otherwise roof trim may be damaged.
4) Remove the bolt to remove the seat belt retrac-
tor.
3. INNER SEAT BELT RH ASSEMBLY
1) Remove the RH second-row seat assembly.
ond-row Seats.>
2) Remove the LH hinge outer cover.
3) Remove the bolt, and then detach the inner belt
assembly.
SB-00308
SB-00309
SB-00236
(A)
SB-00155
SB-00316
SB-00310

SR-2
General Description
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
1. General Description
A: COMPONENT
(1) Glass lid (5) Drain tubeTightening torque: N·m (kgf-m, ft-lb)
(2) Weather strip (6) Motor ASSYT1: 4.5 (0.46, 3.3)
(3) Cover (7) Frame ASSYT2: 6.0 (0.61, 4.4)
(4) Sunshade (8) Deflector
SR-00125
(1)
(2)
(3)
(4)
(5)
(5)
(6)
(7)
T1(8)
T2
T2
T2

SR-3
General Description
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
B: CAUTION
•Before disassembling or reassembling parts, al-
ways disconnect the battery ground cable from bat-
tery. When replacing the audio, control unit, and
other parts provided with memory functions, record
the memory contents before disconnecting the bat-
tery ground cable in order to prevent memory dele-
tion.
•Reassemble the parts in the reverse order of dis-
assembly unless otherwise indicated.
•Adjust parts to the given specifications.
•Connect the connectors securely for reassem-
bly.
•After reassembly, make sure functional parts op-
erate smoothly.
C: PREPARATION TOOL
1. GENERAL TOOL
TOOL NAME REMARKS
Circuit Tester Used for measuring resistance and
voltage.
TO RX®T20Used for the removal of the sun roof
lid and sunshade.

SR-4
Sunroof Control System
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
2. Sunroof Control System
A: WIRING DIAGRAM
1. SUNROOF

B: INSPECTION
•Failure turn of glass lid while driving rough road.
Glass lid has auto-reverse function. When applied above specified force to the glass lid, the lid turns back
and stops. When operating the glass lid (open or close) while driving the rough road, the lid judges vibration
as a force and may causes failure turns. When the failure turn is occurred, need to perform the initialize op-
eration with following procedure.
1. INITIALIZE OPERATION
1) Tilt up the glass lid.
2) Release the switch once, and press the tilt up switch again for 15 seconds.
3) When the glass lid is raised a little and returned to tilt up position, release the switch for the moment. (Ini-
tialization of position detecting function)
4) Holding down the tilt up switch again within 5 seconds from releasing the switch will automatically perform
tilt down/slide open/slide close. (When more than 5 seconds pass, the position detecting function is can-
celled.)
5) Initialize operation is completed.
Symptom Inspection order
Wa t er l e ak ag e 1 . Che ck r o o f p a ne l a n d g la ss li d fo r i mp r o pe r or p oo r se al i ng .
2. Check drain tube for clogging.
3. Check sunroof frame seal and body for improper fit.
Booming noise, wind noise and other noise 1. Check glass lid and roof panel for improper clearance.
2. Check sunshade and roof trim for improper clearance.
Abnormal motor noise 1. Check installing part of motor for looseness.
2. Check gears and bearings for wear.
3. Check cable for wear.
4. Check cable pipe for deformities.
Fai l ur e of su n r oo f
(Motor operates properly.)
1. Check guide rail for foreign particles.
2. Check guide rail for improper installation.
3. Check parts for mutual interference.
4. Check cable slider for improper clinching.
5. Check cable for improper installation.
Motor does not rotate or rotate improperly. 1. Check fuse for blown out.
2. Check switch for improper function.
3. Check motor for incorrect terminal voltage.
4. Check the relay for improper operation.
5. Check poor grounding system.
6. Check harness for open or short and terminals for poor connections.
Fai l ur e tu r n o f gl a ss l i d Ch e ck gu i de ra il fo r fo r e ig n p a r ti cl e s.

SR-5
Glass Lid
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
3. Glass Lid
A: REMOVAL
1) Completely close the glass lid, and then open
the sunshade.
2) Remove the cover (A), and then remove the
TORX® bolts (B).
CAUTION:
The thread locker is applied to the TORX® b o l t s ,
so use the new parts once they are removed.
3) Remove the glass lid carefully.
B: INSTALLATION
Install in the reverse order of removal.
C: ADJUSTMENT
Loosen the glass lid mounting TORX® bolts (A),
and then adjust the height with moving the lid.
Difference in height between glass lid and roof
panel L:
2.0±1.0 mm (0.079 ± 0.039 in)
(A)
(B)
SR-00091
(A)
SR-00117
L

SR-6
Glass Lid
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
D: FORCED DRIVE
If glass lid dose not operate or is not supplied with
power, move the glass lid using the hexagon
wrench *.
*: L shape universal purpose hexagon wrench
bolt width 4 mm (0.16 in)
1) Remove the spot map light. MOVAL, Spot Map Light.>
2) Remove the sunroof opening trim.
3) Remove the sun visor clip.
4) Insert the hexagon wrench securely until it
touches the motor shaft edge.
CAUTION:
Make sure not to bend or wrinkle the roof trim
during work.
5) Turn the hexagon wrench, and move the glass
lid.
•Turning right, the glass lid open.
•Turning left, the glass lid close.
EI-00501