2009 SUBARU TRIBECA Harness

LI-24
Rear Finisher Light Assembly
LIGHTING SYSTEM
22.Rear Finisher Light Assembly
A: REMOVAL
1) Remove the bulb inspection cover of the rear
gate trim.
2) Disconnect the harness connector.
3) Remove the mounting nuts and detach the rear
finisher assembly.
B: INSTALLATION
Install in the reverse order of removal.
LI-00516
(A)
LI-00517

LI-29
Spot Map Light
LIGHTING SYSTEM
27.Spot Map Light
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the lens.
3) Remove the four bolts used for mounting the
spot map light.
4) Disconnect the harness connectors and remove
the spot map light.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. SPOT MAP LIGHT BULB
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
2. SPOT MAP LIGHT SWITCH
Measure the resistance between spot map light
switch terminals.
Switch position Terminal No. Standard
OFF — 1 MΩ or more
ON 1 and 2 18±5.4 Ω
LI-00521
LI-00522

LI-30
Room Light
LIGHTING SYSTEM
28.Room Light
A: REMOVAL
1. MODEL WITHOUT REAR ENTERTAIN-
MENT SYSTEM
1) Disconnect the ground cable from battery.
2) Remove the lens (A) and mounting screws (B).
3) Disconnect the harness connector and remove
the room light.
2. MODEL WITH REAR ENTERTAINMENT
SYSTEM
The room light bulb is integrated into the rear enter-
tainment system as a single unit; therefore, refer to
Rear Entertainment System for the removal proce-
dure. ment.>
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. ROOM LIGHT BULB
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
2. ROOM LIGHT SWITCH
Measure the resistance between room light switch
terminals.
LI-00315
(A)
LI-00316(B)
Switch position Terminal No. Standard
OFF — 1 MΩ or more
ON 1 and 3 1.5±0.5 Ω
DOOR 2 and 3 1.5±0.5 Ω
LI-00257
321

LI-31
Luggage Room Light
LIGHTING SYSTEM
29.Luggage Room Light
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the luggage room light body (A).
3) Disconnect the harness connector and remove
the lens.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. LUGGAGE ROOM LIGHT BULB
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
2. LUGGAGE ROOM LIGHT SWITCH
Measure the resistance between luggage room
light switch terminals.
Switch position Terminal No. Standard
OFF — 1 MΩ or more
ON 1 and 2 1.5±0.5 Ω
DOOR 2 and 3 1.5±0.5 Ω
LI-00258
(A)
LI-00259
321

LI-32
Rear Gate Light
LIGHTING SYSTEM
30.Rear Gate Light
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the bulb inspection cover of rear gate
trim, then disconnect the harness connectors.
3) Remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. REAR GATE LIGHT BULB
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
2. REAR GATE LIGHT SWITCH
Measure the resistance between trunk lid switch
terminals.
LI-00523
LI-00524
Tr u n k l i d p o s i t i o n Te r m i n a l N o . S t a n d a r d
Close1 and 31 MΩ or more
Open 1.5±0.5 Ω
LI-00529
321

LI-33
Glove Box Light
LIGHTING SYSTEM
31.Glove Box Light
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the glove box. AL, Glove Box.>
3) Disconnect the harness connector.
4) Remove the glove box light.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification.
tion.>
3) If NG, replace the bulb with a new one.
LI-00525

LI-34
Door Step Light
LIGHTING SYSTEM
32.Door Step Light
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the rear door trim. MOVAL, Door Trim.>
3) Disconnect the harness connector.
4) Remove the mounting screw from the rear side
of trim and remove the door step light.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification.
tion.>
3) If NG, replace the bulb with a new one.
LI-00526

OD(diag)-4
General Description
OCCUPANT DETECTION SYSTEM (DIAGNOSTICS)
3. General Description
A: CAUTION
1) Never remove the occupant detection control
module, occupant detection sensor and seat cush-
ion from seat frame because the occupant detec-
tion system is integrated into seat frame as one
unit.
2) Always perform “system calibration (Rezeroing)”
when removing or removing and disassembling the
passenger’s seat. CALIBRATION (REZEROING), OPERATION,
Subaru Select Monitor.>
3) Never connect the battery in reverse polarity.
•Occupant detection system may be destroyed in-
stantly.
4) Do not disconnect the battery terminals while the
engine is running.
•A large counter electromotive force will be gener-
ated in the generator, and this voltage may damage
electronic parts such as occupant detection control
module.
5) Before disconnecting the connectors of each
sensor and control module, be sure to turn the igni-
tion switch to OFF and wait for 20 seconds or more.
•Occupant detection control module may be dam-
aged.
6) Every A/C-related part is a precision part. Do not
drop them.
7) Airbag system wiring harness is routed near the
A/C control panel and junction box.
CAUTION:
•For airbag system, yellow-colored wiring har-
ness and connectors are all used. Do not use
the electrical test equipment on these circuits.
•Be careful not to damage the airbag system
wiring harness when servicing the occupant
detection system.
•Refer to “Airbag System” when repairing the
occupant detection system. 4, CAUTION, General Description.>
B: INSPECTION
Measure the battery voltage and check electrolyte.
Standard voltage: 12 V
Specific gravity: Above 1.260