2009 SUBARU TRIBECA brake sensor

BVC(diag)-6
Electrical Component Location
BRAKE VACUUM CONTROL (BVC) (DIAGNOSTICS)
4. Electrical Component Location
A: LOCATION
(1) Brake vacuum pump relay (4) Test mode connector (6) Data link connector
(2) Brake vacuum pump (5) Engine control module (ECM) (7) Odo/trip meter
(3) Brake vacuum sensor
BR-00520
(1)
(2)(3)
(7)
(4)
(5)
(6)

BVC(diag)-8
Engine Control Module (ECM) I/O Signal
BRAKE VACUUM CONTROL (BVC) (DIAGNOSTICS)
5. Engine Control Module (ECM) I/O Signal
A: ELECTRICAL SPECIFICATION
DescriptionConnector
No.
Te r m i n a l
No.
Signal (V)
NOTEIgnition SW ON
(engine OFF)
Engine ON
(idling)
Brake vacuum
sensor
Signal B134 27 1 — 3.8 1 — 3.8 —
Pow er s up pl y B 1 35 2 2 5 5 —
Ground B135 30 0 0 —
Self-shutoff control B136 23 0 0 —
Brake vacuum
pump
Relay drive B136 8
10 — 13
(When the pump is OFF)
12 — 14
(When the pump is ON)—
0 (When the pump is ON) 0 (When the pump is ON)
Electric load B135 25
0 (When the pump is OFF) 0 (When the pump is OFF)
—10 — 13
(When the pump is ON)
12 — 14
(When the pump is ON)
SSM communication line B136 16 1 or less ←→ 4 or more 1 or less ←→ 4 or more —
EN-01812
B134
5678219431024 2223251112131415262728
1617181920213334 2932 3031
B136
5678219431024 2223251112131415262728
16171819202133342932303135
B135
5678219431024 2223251112131415262728
16171819202129303132333435
B137
5678219431022231112131415242526
1617181920212728293031
ToToToTo

BVC(diag)-14
List of Diagnostic Trouble Code (DTC)
BRAKE VACUUM CONTROL (BVC) (DIAGNOSTICS)
10.List of Diagnostic Trouble Code (DTC)
A: LIST
DTC Display Content of diagnosis Reference target
11 Sensor output out of rangeBrake vacuum sensor output
error
OUT OF RANGE, Diagnostic Procedure with Diag-
nostic Trouble Code (DTC).>
12 Compare error in other sensor
Error in comparison with other
brake booster relative pres-
sure
IN OTHER SENSOR, Diagnostic Procedure with
Diagnostic Trouble Code (DTC).>
13 Pressure sensor outputBrake vacuum sensor seizure
malfunction
SOR OUTPUT, Diagnostic Procedure with Diagnos-
tic Trouble Code (DTC).>
21 Discrepancy in relays (ON)
Drive does not match
between the brake vacuum
pump relay and the brake vac-
uum pump.
RELAYS (ON), Diagnostic Procedure with Diagnos-
tic Trouble Code (DTC).>
22 Discrepancy in relays (OFF)
Drive does not match
between the brake vacuum
pump relay and the brake vac-
uum pump.
RELAYS (OFF), Diagnostic Procedure with Diag-
nostic Trouble Code (DTC).>
23 Pump continuous workMalfunction in brake vacuum
pump continuous operation
OUS OPERATION, Diagnostic Procedure with
Diagnostic Trouble Code (DTC).>

BVC(diag)-15
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
BRAKE VACUUM CONTROL (BVC) (DIAGNOSTICS)
11.Diagnostic Procedure with Diagnostic Trouble Code (DTC)
A: DTC 11 SENSOR OUTPUT OUT OF RANGE
DTC DETECTING CONDITION:
Brake vacuum sensor malfunction
TROUBLE SYMPTOM:
Brake vacuum pump does not operate.
WIRING DIAGRAM:
BR-00528
2
1
B25B
B422
1234
B432
2
1
4
36
5
8
7
B432
SBF HOLDER
3
7
14
21
53
43
VC2
VC3
B422
B422
VC3
RELAY BOX(VACUUMPUMP RELAY)
B417
VAC U U MPUMP
26
41
B47
MAINRELAY
B411
VAC U U M S E N S O RECM
A: B134B: B135C: B136
C23B30B22A27C8312
JOINT CONNECTOR
B424
**
B417B411
213
B: C:B135
5672134
29
101112131415252416
30
98171819202821222332312627333435
B136
16101112131415252430
9871718192028212223293231
123456
2726333435
VC2
A:B134
85610 11 12 13 14 157213416
3019 20 2228 29
91718252123 24323126 2733 34
B424
34561278
(BROWN)
21
5436
B47
* : TERMINAL NO. OPTIONAL ARRANGEMENT
21
SBF-7BATTERY
30A
3412
5
8967
10131211
14

BVC(diag)-16
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
BRAKE VACUUM CONTROL (BVC) (DIAGNOSTICS)
Step Check Yes No
1CHECK BRAKE VACUUM SENSOR.
1) Turn the ignition switch to OFF.
2) Disconnect the brake vacuum sensor con-
nector.
3) Remove the brake vacuum sensor. BR-40, REMOVAL, Brake Vacuum Sensor.>
4) Measure the resistance between brake
vacuum sensor connector terminals.
Te r m i n a l s
No. 1 — No. 3:
No. 2 — No. 3:
Is the resistance 15 kΩ or
less?
Go to step 2.Replace the brake
vacuum sensor.
Brake Vacuum
Sensor.>
2CHECK HARNESS BETWEEN ECM AND
BRAKE VACUUM SENSOR CONNECTOR.
1) Disconnect the connectors from ECM.
2) Measure the resistance of the harness
between ECM and the brake vacuum sensor
connector.
Connector & terminal
(B135) No. 30 — (B411) No. 1:
(B135) No. 22 — (B411) No. 3:
(B134) No. 27 — (B411) No. 2:
Is the resistance less than 1
Ω?
Go to step 3.Repair the open
circuit of harness
between ECM and
brake vacuum
sensor connector.
3CHECK HARNESS BETWEEN ECM AND
BRAKE VACUUM SENSOR CONNECTOR.
Measure the resistance of harness between
ECM and chassis ground.
Connector & terminal
(B135) No. 30 — Chassis ground:
(B135) No. 22 — Chassis ground:
(B134) No. 27 — Chassis ground:
Is the resistance more than 1
MΩ?
Go to step 4.Repair the ground
short of the har-
ness between
ECM and brake
vacuum sensor
connector.
4CHECK HARNESS BETWEEN ECM AND
BRAKE VACUUM SENSOR CONNECTOR.
Measure the voltage between ECM connector
and chassis ground.
Connector & terminal
(B135) No. 30 (+) — Chassis ground (–):
(B135) No. 22 (+) — Chassis ground (–):
(B134) No. 27 (+) — Chassis ground (–):
Is the voltage less than 0.5 V? Go to step 5.Repair the battery
short circuit
between ECM and
brake vacuum
sensor connector.
5CHECK THE BRAKE VACUUM SENSOR
POWER SUPPLY.
1) Connect the connectors to ECM and brake
vacuum sensor.
2) Turn the ignition switch to ON.
3) Measure the voltage between ECM con-
nector terminals.
Connector & terminal
(B135) No. 22 (+) — (B135) No. 30 (–):
Is the voltage 4.75 — 5.25 V? Go to step 6.Replace the ECM.
FU(H6DO)-32,
Engine Control
Module (ECM).>
6CHECK CURRENT DATA.
1) Turn the ignition switch to ON.
2) Depress the brake pedal several times, until
the pedal becomes firm.
3) Read the current data of the brake negative
pressure pump system using the Subaru
Select Monitor. Select Monitor.>
Is the atmospheric pressure —
brake booster pressure
between –8 — +8 mmHg?
Te m p o r a r y p o o r
contact occurs.
Replace the ECM.
FU(H6DO)-32,
Engine Control
Module (ECM).>

BVC(diag)-17
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
BRAKE VACUUM CONTROL (BVC) (DIAGNOSTICS)
B: DTC 12 COMPARE ERROR IN OTHER SENSOR
DTC DETECTING CONDITION:
Brake vacuum sensor malfunction
TROUBLE SYMPTOM:
Brake vacuum pump does not operate.
WIRING DIAGRAM:
BR-00528
2
1
B25B
B422
1234
B432
2
1
4
36
5
8
7
B432
SBF HOLDER
3
7
14
21
53
43
VC2
VC3
B422
B422
VC3
RELAY BOX(VACUUMPUMP RELAY)
B417
VAC U U MPUMP
26
41
B47
MAINRELAY
B411
VAC U U M S E N S O RECM
A: B134B: B135C: B136
C23B30B22A27C8312
JOINT CONNECTOR
B424
**
B417B411
213
B: C:B135
5672134
29
101112131415252416
30
98171819202821222332312627333435
B136
16101112131415252430
9871718192028212223293231
123456
2726333435
VC2
A:B134
85610 11 12 13 14 157213416
3019 20 2228 29
91718252123 24323126 2733 34
B424
34561278
(BROWN)
21
5436
B47
* : TERMINAL NO. OPTIONAL ARRANGEMENT
21
SBF-7BATTERY
30A
3412
5
8967
10131211
14

BVC(diag)-18
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
BRAKE VACUUM CONTROL (BVC) (DIAGNOSTICS)
Step Check Yes No
1CHECK BRAKE VACUUM HOSE.
1) Turn the ignition switch to OFF.
2) Check that status of the brake vacuum
hose connection.
Is the brake vacuum hose con-
nected firmly?
Go to step 2.Connect the brake
vacuum hose.
2CHECK BRAKE VACUUM HOSE.
1) Turn the ignition switch to ON and start
engine.
2) Check for leakage from the brake vacuum
hose.
Is there a leak from the brake
vacuum hose?
Replace the brake
vacuum hose.
Go to step 3.
3CHECK BRAKE VACUUM SENSOR.
1) Turn the ignition switch to OFF.
2) Disconnect the brake vacuum sensor con-
nector.
3) Remove the brake vacuum sensor. BR-40, REMOVAL, Brake Vacuum Sensor.>
4) Measure the resistance between brake
vacuum sensor connector terminals.
Te r m i n a l s
No. 1 — No. 3:
No. 2 — No. 3:
Is the resistance 15 kΩ or
less?
Go to step 4.Replace the brake
vacuum sensor.
Brake Vacuum
Sensor.>
4CHECK HARNESS BETWEEN ECM AND
BRAKE VACUUM SENSOR CONNECTOR.
1) Disconnect the connectors from ECM.
2) Measure the resistance of the harness
between ECM and the brake vacuum sensor
connector.
Connector & terminal
(B135) No. 30 — (B411) No. 1:
(B135) No. 22 — (B411) No. 3:
(B134) No. 27 — (B411) No. 2:
Is the resistance less than 1
Ω?
Go to step 5.Repair the open
circuit of harness
between ECM and
brake vacuum
sensor connector.
5CHECK HARNESS BETWEEN ECM AND
BRAKE VACUUM SENSOR CONNECTOR.
Measure the resistance of harness between
ECM and chassis ground.
Connector & terminal
(B135) No. 30 — Chassis ground:
(B135) No. 22 — Chassis ground:
(B134) No. 27 — Chassis ground:
Is the resistance more than 1
MΩ?
Go to step 6.Repair the ground
short circuit
between ECM and
brake vacuum
sensor connector.
6CHECK HARNESS BETWEEN ECM AND
BRAKE VACUUM SENSOR CONNECTOR.
Measure the voltage between ECM and chas-
sis ground.
Connector & terminal
(B135) No. 30 (+) — Chassis ground (–):
(B135) No. 22 (+) — Chassis ground (–):
(B134) No. 27 (+) — Chassis ground (–):
Is the voltage less than 0.5 V? Go to step 7.Repair the battery
short of the har-
ness between
ECM and brake
vacuum sensor
connector.
7CHECK THE BRAKE VACUUM SENSOR
POWER SUPPLY.
1) Connect the connectors to ECM and brake
vacuum sensor.
2) Turn the ignition switch to ON.
3) Measure the voltage between ECM con-
nector terminals.
Connector & terminal
(B135) No. 22 (+) — (B135) No. 30 (–):
Is the voltage 4.75 — 5.25 V? Go to step 8.Replace the ECM.
FU(H6DO)-32,
Engine Control
Module (ECM).>

BVC(diag)-20
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
BRAKE VACUUM CONTROL (BVC) (DIAGNOSTICS)
C: DTC 13 PRESSURE SENSOR OUTPUT
DTC DETECTING CONDITION:
Brake vacuum sensor malfunction
TROUBLE SYMPTOM:
Brake vacuum pump does not operate.
WIRING DIAGRAM:
BR-00528
2
1
B25B
B422
1234
B432
2
1
4
36
5
8
7
B432
SBF HOLDER
3
7
14
21
53
43
VC2
VC3
B422
B422
VC3
RELAY BOX(VACUUMPUMP RELAY)
B417
VAC U U MPUMP
26
41
B47
MAINRELAY
B411
VAC U U M S E N S O RECM
A: B134B: B135C: B136
C23B30B22A27C8312
JOINT CONNECTOR
B424
**
B417B411
213
B: C:B135
5672134
29
101112131415252416
30
98171819202821222332312627333435
B136
16101112131415252430
9871718192028212223293231
123456
2726333435
VC2
A:B134
85610 11 12 13 14 157213416
3019 20 2228 29
91718252123 24323126 2733 34
B424
34561278
(BROWN)
21
5436
B47
* : TERMINAL NO. OPTIONAL ARRANGEMENT
21
SBF-7BATTERY
30A
3412
5
8967
10131211
14