2009 SKODA YETI Owner's Manual

Driving and the Environment
184
•
Be very alert and look ahead when
driving off-road. Excessive speed or
incorrect driving manoeuvr
es can cause damage to the vehicle and lead to
serious injuries.•
Observe the important guidelines
⇒page 180.
Caution
•
Pay attention to the ground clearance of
the vehicle! The vehicle can be severely
damaged and become disabled once it touches the ground.•
Never drive off-road with an almost empty
fuel tank. The fuel supply to the engine
can be interrupted and therefore the cata
lytic converter can be severely damaged.
•
Do not leave your foot on the clutch peda
l or let the clutch slip when driving off-
road. Overwise you may unintentionally depress the clutch pedal on uneven ground leading to a loss of control over the vehi
cle. In addition, the force for connecting the
engine and the gearbox is lost. Moreover, driving while letting the clutch slip causes a fast wear of the clutch linings.
Note
The fuel consumption is higher when drivin
g off-road than when driving on conven-
tional roads, especially through difficult terr
ain. When you prepare for your journey, be
aware of an increase in fuel consumption; the nearest filling station may be far away.Shifting gears correctlyThe gear you must shift into depends on th
e terrain. Choosing the correct gear contrib-
utes to safe driving. In partic
ular if you do not have much
experience driving off-road,
it is always better, before negotiating a difficult stretch of the road, to pause and reflect on which gear to engage. Your experience will tell you which gear is the best for certain sections of the terrain. Basically:•
When the gear or the driving stage has been
properly selected, it is unnecessary to
slow down the vehicle on a downhill sectio
n using the footbrake as in most cases the
engine braking power is sufficient.
•
Depress the accelerator only as much as is necessary. A too great acceleration may
lead to the wheels spinning and thus result
s in the loss over the control of the vehicle.
Manual gearbox•
If you are driving thro
ugh difficult terrain,
on no account
use the clutch or change
the gear. When the clutch is depressed, th
e vehicle may come to
a standstill because
of the increased grip of all the tyres of the vehicle (e.g. in the mud, in deep sand or on a slope). Once the vehicle has come to a stan
dstill, it may be difficult or even impos-
sible to start off und
er these conditions.
•
When negotiating a steep downhill section
or a steep uphill section, always shift
into the 1st or 2nd gear.•
On a soft or slippery ground, you must
drive at the appropriate speed and you
must select the highest possible gear for this. Automatic gearbox•
Select the selector lever position
for normal flat stretches of terrain
⇒ page 122.•
While in the Tiptronic mode, select the se
lector lever position or if you are
driving through mud,
sand, water or hilly
sections of terrain
⇒page 124.
•
When negotiating a steep downhill sectio
n or a steep uphill section, select the
selector lever position while in the Tiptronic mode.•
On a soft or slippery ground, you must
drive at the appropriate speed and you
must select the highest possible driving stage.Driving over rough and smooth
WARNING (continued)
AD
A3
A2
A1
Fig. 165 Observe the ground clearance
sgg.6.book Page 184 Thursday, September 24, 2009 2:32 PM

Driving and the Environment
185
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
–Switch on the Off-road mode
⇒page 170.
– Drive at walking speed over rocky passages. – If it is not possible to drive around a ston
e, gently drive onto
the stone with one of
the front wheels and then drive over it slowly.
WARNING
Observe the important guidelines
⇒page 180.
Caution
•
On no account drive over large objects (suc
h as pieces of rock
or tree stumps),
neither in the middle nor on one side. When driving over objects which are larger than the ground clearance, the chassis and its
components can get da
maged. Your vehicle
could break down far away from any assistance.•
Even objects that are smaller than the ex
isting ground clearance can come into
contact with the underbody of the vehicle an
d can lead to damage or failure of the
vehicle. This applies especially when there is
a hollow or soft ground in front or behind
the object or if you drive too fast over th
e object and thus the vehicle is deflected.
For the sake of the environment
Leaking engine oil and brake fluid pollute the environment and contaminate the bodies of water. The dispos
al e.g. of engine oil soaked soil can be costly.
Crossing bodies of waterParticular attention is required wh
en driving through bodies of water
⇒page 179.
Driving through snow-covered terrain– Before you drive through snow-covered te
rrain, mount snow chains on the front
wheels or on the rear wheels
⇒page 219, “Snow chains” in order to achieve the
best possible traction.
–Switch on the Off-road mode
⇒page 170.
Even harmless looking sections of terrain can be dangerous. This applies in particular for sections where no ruts or other tracks are visible.
WARNING
•
Driving through snow-covered terrain poses special dangers. Never choose
a dangerous route and never take a risk which could jeopardize your safety and that of your passengers. If you cannot go on or if you doubt the safety of the route, turn back and choose another way.•
Potholes, troughs, trenches, precipices,
sheets of ice or other obstructions
are often completely or partially obscured by snow.•
The hidden dangers of snow can cause an accident, serious injuries or your
vehicle to break down under
extreme weather conditions.
Driving over steep terrainDriving uphill and downhill– Stop the vehicle before driving uphill or
downhill, exit the vehicle and explore the
situation.
– Walk a stretch and check the firmness of the soil and look for obstructions or other
hidden dangers.
– Check how the route continues beyond the slope. – Switch on the Off-road mode
⇒page 170.
– Drive slowly and steadily straight uphill or downhill.– Do not stop the vehicle on a hillside or attempt to turn around. – You must prevent the engine from cutting out.Driving uphill– Check before driving over a hilltop, how it
continues on the other side. If you drive
up a steep hill, the vehicle faces the sky and you cannot see what is directly in front of the vehicle.
– Switch on the Off-road mode
⇒page 170.
sgg.6.book Page 185 Thursday, September 24, 2009 2:32 PM

Driving and the Environment
186
– Do not shift gears or release the
clutch during th
e climbing phase.
– Depress the accelerator only as much as
is necessary in order
to handle the slope.
If you can go no further on a slope– Never attempt to make a turn with the vehicle on a hillside. – If the engine cuts out, press the foot brake and restart the engine. – Engage the reverse gear and carefully
drive backwards in your own tracks.
– Press the foot brake in order to maintain a constant speed.Driving downhill–Switch on the Off-road mode
⇒page 170.
– Shift into first gear or select the first driving stage, while in the Tiptronic mode, to
drive downhill on steep hillsides in order
to use the Downhill Drive Support to its
maximum.
– Press the foot brake gently, so you do not lose the control over your vehicle. – If it is feasible and safe, drive straight down (maximum gradient).– Do not release the clutch or shift into Neutral.
WARNING
•
Never attempt to drive uphill or downhill if it is too steep for your vehicle.
The vehicle could slip or roll
over - risk of accident!
•
Never attempt to make a turn on a hillside. The vehicle could tilt or roll over.
This can result in serious accidents.•
If the engine cuts out on a slope or
you can no longer go on for whatever
other reason, then stop!•
Never let the vehicle roll down the hill
side at idling speed. You can lose the
control over your vehicle.•
If the engine cuts out, press the foot brake and restart the engine. Engage the
reverse gear and carefully drive backward
s in your own tracks. Use the engine
braking power and press the foot brake in order to maintain a slow and constant speed.
•
Observe the important guidelines
⇒page 180.
Driving at an angle on a hillsideFig. 166 Steer and maintain your trajectory
/ in direction to exit - facing uphill
Driving at an angle on a hillside is one of the most dangerous situations while driving off-road. It may look harmle
ss, but you must never underestimate the difficulties and
the dangers when driving at an angle on a
hillside. Basically you should avoid moving
your vehicle into a sideways
position on a hillside. Unde
r certain circumstances, the
vehicle can slide away uncontrollably or roll over. Check before driving in a tilted position, whether there is a different and safer route. If you have to drive in a tilted position, then
the ground should be as firm and even as
possible. Note that the vehicle may slide sideways or sink in and roll over when driving on slippery or soft ground. Make sure that
the inclination is not too steep when driving
over surface irregularities. Otherwise, the vehicle can roll over and then roll down the hillside. If the vehicle is at a very steep angle, the wheels on the low side must not sink deeply into the ground or into troughs and you mu
st not drive over stones, tree stumps or
other obstructions with the alternate raised wheels. If there is a risk your ve
hicle may tilt, steer immedi
ately in direction of dip
⇒fig. 166

and lightly depress the accelerator. The centre
of gravity of the vehicle should be as low
as possible. Distribute the weight of all the occupants of the vehicle evenly. Taller and heavier people should be seated on the rais
ed side of the vehicle. The luggage on the
WARNING (continued)
sgg.6.book Page 186 Thursday, September 24, 2009 2:32 PM

Driving and the Environment
187
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
roof should be removed and secured, as the
vehicle could tilt by
a sudden shifting of
the luggage. A passenger, seated at the rear, should always
remain seated on the seat facing up the
hill during such a journey. In an extreme ca
se, the passenger on the relevant side must
exit the vehicle until you have
safely crossed the hillside.
Exiting the vehicle on a hillside If the vehicle comes to a standstill at a steep angle on a hillside and you and your passengers must exit the vehicle, then all th
e occupants should exit on the side facing
up the hill
⇒page 186, fig. 166
on the right.
WARNING
•
Never attempt to drive uphill or downhill if it is too steep for your vehicle.
The vehicle could slip, tilt or roll over - risk of accident!•
When driving at an angle on a hillside,
the vehicle can lose its grip and slide
sideways. The vehicle can tilt or roll over
and then roll down the hillside. This
can lead to serious injuries.•
Always make sure that when the vehicle
is at an angle, the wheels on the low
side do not sink deeply into the ground or into troughs and do not drive over stones, tree stumps or other obstructions
with the alternate ra
ised wheels - risk
of accident!•
Before you drive at an angle on a hillside
⇒page 186, fig. 166
, make sure
that you can steer and maintain your trajectory. If this is not possible, choose a different path. If you drive at an angle
on a hillside and there is a risk your
vehicle may tilt, steer imme
diately downhill on your trajectory and lightly
depress the accelerator.•
If the vehicle is stationary on a hillside
with a too great angle of lateral incli-
nation, avoid sudden and uncontrolled movements in the vehicle. The vehicle can roll over and then roll down the hillside. This can lead to serious injuries.•
If the vehicle is stationary on a hillside
with a too great angle of lateral incli-
nation, neither you nor your occupants must exit the vehicle through the doors facing downhill. This can lead to a shift of the overall centre of gravity. The vehicle can tilt or roll over and then roll down the hillside. This can lead to serious injuries. To avoid this, you and your occupants must exit the vehicle only on the side facing uphill
⇒page 186, fig. 166
.
•
When you exit the vehicle, make sure
that the door which faces uphill does
not close by its own weight or by carelessness - risk of injury!•
Observe the important guidelines
⇒page 180.
Driving over rutted roads and troughsYou will always encounter ruts when drivin
g on forest roads, through wet meadows
and fields as well as on rutted stretches of terrain. If the ruts and troughs are on firm and soft ground, you can simply follow the ruts.Do not drive over ruts and troughs which are
too deep. If you cannot avoid this, it is
better that you turn back.
Caution
If the ruts or troughs become too deep,
the underbody of the vehicle can touch the
ground, which might cause the
underbody to get damaged. Therefore, avoid driving in
deep ruts and troughs.Crossing a trenchIf possible, drive through the trench at an acute angle. Make sure when driving through the trench that the tilt angle is not too steep.
WARNING
Never attempt to drive through a trench if its embankment is too steep. The vehicle could slip, tilt or roll over - risk of accident!
Caution
If you drive into the trench at a right angle,
the front wheels will sink into the trench.
There is also the danger that the underbod
y of the vehicle touches the ground and is
damaged. For these reasons (even with four-wheel drive) it is rarely possible to get out of the trench.
WARNING (continued)
sgg.6.book Page 187 Thursday, September 24, 2009 2:32 PM

Driving and the Environment
188
Driving in sand and mudYou should therefore always drive at a constant speed through sand or mud whenever possible and at the same time do not shift gears or change the driving stage. –Switch on the Off-road mode
⇒page 170.
– Select a suitable gear or driving stage and maintain the gear or driving stage. – Keep your vehicle in constant motion and
do not stop until you have reached firm
ground.
Never drive too fast, otherwise the wheels may spin and the vehicle can get stuck. If you feel that the tyres do no longer grip, then turn the steering wheel quickly back and forth. This leads to an improved adhesion of the front tyres of the vehicle for a short period of time. Driving through sand Do not reduce
the tyre inflation pressure. If you nevertheless reduce the inflation
pressure, do not forget to re-establish the correct tyre inflation pressure level before you continue driving. Driving with a reduced tyre inflation pressure increases the risk that you lose control over your vehi
cle and that the vehicle rolls over.
Driving through mud Do not change speed or direction when you
drive through the mud.
The tyres can lose
their grip in the mud. If th
e vehicle slides, you must stee
r in the appropriate direction
in order to regain control over the vehicle.
WARNING
•
Driving through mud can be dangerous. The vehicle can slide uncontrol-
lably which causes an increased risk of injury. Adopt a particularly cautious style of driving. Pay attention to the information and warning notes.•
An incorrect tyre inflation pressure may cause a major or fatal accident! An
incorrect tyre inflation pressure may result in bursting of a tyre, which causes the vehicle to get out of control.•
Observe the important guidelines
⇒page 180.
Stuck vehicleIf you can no longer drive on ...– Carefully dig out all the wheels and make sure that no other parts of the vehicle are
stuck in the sand.
– Engage the reverse gear. – Gently depress the accelerator and try
to drive backwards in your own track.
– Place scrub, footmats or a sackcloth directly
in front of the tyres in order to improve
the road adherence and thus achieve an improved traction to drive out.
Rocking out vehicle– Switch off the TCS
⇒page 165.
– Set the steering wheel straight. – Drive so far back until the wheels just begin to spin.– Quickly shift into first gear and drive
forwards until the wheels begin to spin.
– Drive back and forth repeat
edly until the momentum is
sufficient to free the
vehicle.
– Switch on the TCS.A few tips– Ensure that the Off-road mode is switched on
⇒page 170.
– Avoid prolonged spinning of the wheels,
otherwise the vehicl
e would still sink
deeper into the ground.
– Remove mud, dirt and stones from the tread of the tyre. You need training and
experience if you wish to rock
out a vehicle. If you make a
mistake, the vehicle can still sink in further
and you can only free it with the help of
others.
WARNING
Observe the important guidelines
⇒page 180.
sgg.6.book Page 188 Thursday, September 24, 2009 2:32 PM

Driving and the Environment
189
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
After driving off-roadCheck the vehicle for damage after driving off-road - especially on the underside of the vehicle. – Switch off the Off-road mode
⇒page 170.
– Check the tyres and the axles for damage and remove coarse dirt, stones and
foreign bodies from the tyre tread.
– Clean the turn signal lights, the headlights, the number plate and the windows. – Check the underbody of the vehicle and re
move trapped objects, such as scrub or
wood pieces.
– Contact your specialist gara
ge if you detect any damage.
– In case of thick layers of
dirt, clean the radiator grille, the engine compartment and
the underbody of the vehicle.
WARNING
•
Combustible materials which are trapped under the vehicle floor can be
dangerous. They can impair the driving
safety and the safety of all the occu-
pants of the vehicle. After driving off-
road, always check the underside of the
vehicle and remove trapped objects.•
Never continue the journey if objects
are trapped under the vehicle. This
can damage the fuel lines, the brake sy
stem, the seals and other parts of the
chassis.•
Combustible objects such as dry leaves or twigs could ignite on hot vehicle
parts. A vehicle fire can also lead to serious injuries.•
Observe the important guidelines
⇒page 180.
sgg.6.book Page 189 Thursday, September 24, 2009 2:32 PM

Towing a trailer
190
Towing a trailerTo w i n g a t r a i l e rTechnical requirements The towing device must satisfy certain technical requirements.Your vehicle is designed primarily for tr
ansporting persons and luggage. It can,
however, also be used for towing a traile
r - provided certain technical equipment is
fitted. If your vehicle has already been supplied with a
factory-fitted
towing device then
everything that is nece
ssary for towing a trailer in technical terms, and in terms of the
law, has already been taken into account. Your vehicle is fitted with a 13-pin power so
cket for the electrical connection between
the vehicle and trailer. If the tr
ailer which you wish to tow has a
7-pin connector
, you
can use a suitable adapter
14) from Škoda original accessories.
This work must be carried out in accordance
with the manufacturer's specifications if
a towing device is retrofitted. Authorised Škoda Service Partners are familiar with details relating to retrofitting a towing device and for any necessary
modifications to the cooling system.
WARNING
We recommend that you have the towing device from Škoda original accesso- ries installed by an authorised Škoda Serv
ice Partner. He is familiar with all the
relevant details relating to retrofitting such equipment. There is a risk of an accident if the towing device is not properly fitted!
General Maintenance There are a number of points to pay attention to when towing a trailer.Trailer load The permissible trailer load must on no account be exceeded. You can negotiate appropriately steeper inclin
es and descents if you do not make full
use of the permissible trailer load. The trailer loads specified only apply for
altitudes
up to 1 000 metres above mean sea
level. The fact that the engi
ne power output drops with increasing height due to a
lowering of air pressure and thus the abil
ity to climb, means that the towed weight
must be reduced by 10% for every further increase of 1 000 metres in height above sea level. The towed weight is the weight of the (laden) vehicle and the (laden) trailer together. One should take this into account
before driving up to higher altitudes.
The trailer and drawbar load information on the type plate of the towing device are merely test data for the towing device. The data relating to your vehicle, which is often less than this test data, can be found in your vehicle registration documents. Distribution of the load Distribute the load in the trailer in such a
way that any heavy items are located as close
as possible to the axle. Secure th
e items to preven
t them slipping.
Tyre pressure Correct the tyre inflation pressure on yo
ur vehicle for that of “fully laden”,
⇒page 215.
The inflation pressure of the tyres fitted to
the trailer adjust in accordance with the
manufacturer's recommendation. Exterior mirrors You have to have additional ex
terior mirrors fitted if you are not able to see the traffic
behind the trailer with the standard rear-view mirrors. Both exterior mirrors should be attached to folding arms. Adjust the mirrors so that they provide you with an adequate field of view to the rear.
14)In some countries the adapter is supplied with the towing device.sgg.6.book Page 190 Thursday, September 24, 2009 2:32 PM

Towing a trailer
191
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Headlights Before starting off with a hitched trailer, also check the setting of the headlights. Alter the setting as necessary with the ai
d of the headlight beam adjuster
⇒page 58.
Detachable ball head The ball rod is detachable on vehicles which
feature a factory-fitted
towing device. It is
stowed together with separate fitting instru
ctions in the spare wheel well in the luggage
compartment of the vehicle. Further information on the towing device
⇒page 192.
Note
•
We recommend that you also have your
vehicle inspected between service inter-
vals if you tow a trailer frequently.•
The handbrake on the towing vehicle must be put on when coupling and decou-
pling the trailer.Driving Tips Particular caution is required when towing a trailer.– Do not, as far as possible, drive with
your vehicle unladen and the trailer laden.
– Do not make full use of the legal maximum speeds. This applies in particular to
downhill sections.
– Apply the brakes in good time. – Keep a check on the coolant temperature gauge if the outside temperature is high. Distribution of weight The distribution of the weight
is very poor if your vehicle
is unladen and the trailer is
laden. Maintain a particularly low speed if you cannot avoid driving with this combina-tion. Driving speed Do not drive faster than 80 km/hour for safety reasons. This also applies for countries in which higher speeds are allowed.
The fact that the driving stability of the vehicle + trailer combination reduces with increasing speed means that the legally allowed speed should not be used when there are unfavourable road, weather or wind cond
itions, particularly near accident black
spots. You must always reduce your speed immediat
ely as soon as you detect even just the
slightest swaying
of the trailer. On no account attempt to stop the trailer from
“swaying” by accelerating. Apply the brakes in good time! If
the trailer is fitted with a
trailer brake
, apply the
brakes gently at first and then brake firmly. This will avoid brake jolts resulting from the trailer wheels locking. Shift down gears in good time before negotiating a downhill section to allow the engine to also act as a brake. Engine overheating Please keep a check on the coolant temperature gauge if you have to negotiate a lengthy slope in a low gear at a high engi
ne speed when the outside temperature is
very high
⇒page 17, “Coolant temperature gauge”.
If the needle of the coolant temperature gauge moves into the right-hand area or even the red area of the scale, reduce your speed immediately. Stop and switch off the engine if the warning light
 in the instrument cluster begins flashing. Wait a few
minutes and check the level of coolant in the coolant expansion bottle
⇒page 207,
“Inspecting the coolant level”. Please refer to the following guidelines
⇒page 34, “Coolant temperature/ Coolant
quantity
”.
The coolant temperature can be reduced by switching on the heating.Any increase in the cooling effect of the coolant fan through shifting down a gear and increasing the engine speed is not possible
since the fan speed is independent of the
engine speed. One should also not drop a gear
for this reason when towing a trailer as
long as the engine can manage th
e slope without any drop in speed.
sgg.6.book Page 191 Thursday, September 24, 2009 2:32 PM