2009 RENAULT TWINGO Electrical Equipment - Petrol Injection Workshop Manual

17B-225V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET351INJECTION ELECTRONIC STABILITY PROGRAM CONNECTION
STATUS
DEFINITIONCONNECTED: This status indicates that the connection between the injection
computer and the ESP is not defective.
DISCONNECTED: This status indicates that the connection between the injection
computer and the ESP is defective.
NOTESSpecial notes:
Perform these checks if the parameters correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
NOT CONNECTEDThe connection between the injection computer and the ESP is defective, test the
ABS/ESP computer (see 38C, Anti-lock braking system) and the multiplex network
(see 88B, Multiplexing).
SIM32_V44_ET351/SIM32_V4C_ET351/SIM32_V50_ET351/SIM32_V54_ET351
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-226V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET405CLUTCH PEDAL SWITCH
STATUS
DEFINITIONACTIVE: this status indicates that the clutch pedal is depressed.
INACTIVE: this status indicates that the clutch pedal is released.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"ACTIVE"Clutch pedal depressed.
Non-conformity of the brake signals and or the clutch switch signals can cause the
engine to race during gear changes.
"INACTIVE"Clutch pedal released.
Non-conformity of the brake signals and or the clutch switch signals can cause the
engine to race during gear changes.
SIM32_V44_ET405/SIM32_V4C_ET405/SIM32_V50_ET405/SIM32_V54_ET405
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-227V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET405
CONTINUED
Sensor electrical conformity
"INACTIVE"Check the condition and fitting of the clutch pedal switch.
Remove the clutch pedal switch, check the insulation between connections M and
86D of component 675, with the switch in the rest position.
–Repeat this operation with the switch engaged, and check the continuity between
the two connections.
If these 2 checks are faulty, replace the switch.
Then check the continuity and absence of interference resistance of the following
connection:
–86D between components 120 and 675.
–Make sure that the earth is in order on connection M of component 675.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
"ACTIVE"Check the condition and fitting of the clutch pedal switch.
Remove the clutch pedal switch, check the insulation between connections M and
86D of component 675, with the switch in the rest position.
–Repeat this operation with the switch engaged, and check the continuity between
the two connections.
If these 2 checks are faulty, replace the switch.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-228V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415CRUISE CONTROL/SPEED LIMITER DEACTIVATION
STATUS
DEFINITIONThis status varies according to engine specifications.
NOTESSpecial notes:
Perform these checks if the parameters correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
STATUS 1:Traction control request.
STATUS 2:Brake pedal depressed.
STATUS 3:Clutch pedal depressed.
STATUS 4:Suspend button pressed.
STATUS 5:Cruise control or speed limiter monitoring.
STATUS 6:Inconsistency between the request and the vehicle speed. Gear lever in neutral
(manual gearbox) or the N position (automatic gearbox).
SIM32_V44_ET415/SIM32_V4C_ET415/SIM32_V50_ET415/SIM32_V54_ET415
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-229V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 1
STATUS 7:
Inconsistency between the request and the vehicle speed.
STATUS 8:
Automatic transmission in defect mode.
STATUS 9:
Vehicle speed monitoring.
STATUS 10:
Monitoring by injection computer.
Sensor electrical conformity
Note:
Cruise control can be activated when the vehicle speed exceeds 18 mph (30 km/h).
Status ET415 shows various reasons for deactivation of the cruise control/speed limiter function, due to a driver
request or the external environment (e.g. STATUS 1).
IMPORTANT:
Clear the fault memory by running command RZ001 Fault memory to reset this status to NONE.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-230V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 2
WITHOUTThis status is present on the diagnostic tool when:
The computer has been reinitialised,
The computer has been reprogrammed.
STATUS 1 Traction control request
If the vehicle is fitted with a traction control system, the cruise control function is
deactivated every time the ABS computer calls for traction control.
Status ET415 becomes STATUS 1 when driving with the cruise control active
(ET042 Cruise control/Speed limiter: CRUISE CONTROL) and when traction
control is requested.
This deactivates cruise control.
Reinitialise status ET415 of the injection computer by applying command
RZ001 Fault memory.
If status ET415 becomes STATUS 1 with no traction control request (see 38C, Anti-
lock braking system).
STATUS 2 Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2, when the vehicle is being driven, with cruise
control active (ET042) and the brake pedal depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001.
If status ET415 becomes STATUS 2 without pressing the brake pedal, consult the
interpretation of statuses ET704 and ET705 Brake contact No. 1 and No. 2.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-231V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 3
STATUS 3 Clutch pedal depressed
Manual gearbox only:
The cruise control function is deactivated when the gearbox is not coupled to the
engine (clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with cruise control active
(ET042 Cruise control/Speed limiter: CRUISE CONTROL) and the clutch pedal
is depressed.
This deactivates cruise control.
Reinitialise status ET415 of the injection computer by applying command
RZ001 Fault memory.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed,
consult the interpretation of status ET405 Clutch pedal switch.
If the vehicle is fitted with automatic transmission:
Carry out a multiplex network test, check the configuration of the multiplex network
according to the vehicle's technical specifications and, in particular, the automatic
gearbox computer configuration (see 88B, multiplex).
STATUS 4 Cancel button pressed
The cruise control/speed limiter function is deactivated each time the suspend button
is pressed.
Status ET415 becomes STATUS 4, when driving when:
–Either the cruise control is active, or
–the speed limiter is active
–and when the "0" button is pressed by the driver.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command
RZ001.
If status ET415 becomes STATUS 4 without pressing the 0 button, consult the
interpretation of status ET703: Cruise control/speed limiter buttons and run fault
finding on the R/0 control button located on the right-hand side of the steering wheel.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-232V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 4
STATUS 5 Cruise control or speed limiter monitoring
This status appears when the vehicle brakes or decelerates sharply without the
injection computer receiving a signal indicating that the brake pedal switch has
been pressed.
If status ET415 is STATUS 5, consult the interpretation:
–of status ET042 Cruise control/Speed limiter,
–of status ET703 Cruise control/Speed limiter buttons,
–of status ET704 Brake switch no. 1,
–and status ET705 Brake switch no. 2,
to test the cruise control/speed limiter system components and find the defective
component.
Also check the operation of the accelerator pedal, and check for any faults shown
on the diagnostic tool relating to this component. Deal with them if necessary.
Reinitialise status ET415 of the injection computer by applying command
RZ001 Fault memory.
If status ET415 becomes STATUS 5, deal with any faults that are present or stored
in the injection computer.
If the fault is still present, contact the Techline.
STATUS 6 Gear lever in neutral (manual gearbox) or neutral (automatic transmission).
Status ET415 changes to STATUS 6, when driving, with cruise control active
(ET042) and:
if the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
if the gear lever is in neutral on an automatic transmission.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001.
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on
a manual gearbox without declutching, or into neutral on an automatic transmission,
test the ABS computer and check the configuration of the tyre size stored in the
computer. If the configuration is correct, contact the Techline.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.