2009 RENAULT SCENIC cruise control

DIESEL INJECTION
Fault finding – Conformity check13B
13B - 166V3 MR-372-J84-13B250$540.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
CRUISE CONTROL/SPEED LIMITER
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test Conditions: ENGINE AT IDLE SPEED, COOLANT TEMPERATURE > 80 ˚C.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Cruise
control/speed
limiterET042Cruise
control/speed
limiter- NOT DETECTED: Vehicle
not equipped with cruise
control/speed limiter function
buttons or after
reprogramming the injection
computer, the switch is in the
rest position.
- INACTIVE: When no button
is pressed.
- SPEED LIMITER: Main
switch to speed limiter
position.
- CRUISE CONTROL: Main
switch to cruise control
position.In the event of a fault, refer
to the interpretation of
status ET042 Cruise
control/speed limiter.
2Keys ET703: Cruise
control/speed
limiter buttons- INACTIVE: No cruise
control/speed limiter buttons
are pressed. These buttons
are located on the steering
wheel.
- PLUS: When the cruise
control/speed limiter
“+” button is pressed. This
button is on the steering
wheel, on the left-hand side.
- MINUS: When the cruise
control/speed limiter
“-” button is pressed. This
button is on the steering
wheel, on the left-hand side.
- SUSPEND: When the cruise
control/speed limiter
“0” button is pressed. This
button is located on the
steering wheel, to the right.
- RESUME: When the cruise
control/speed limiter
“R” button is pressed. This
button is located on the
steering wheel, to the right.In the event of a fault,
consult the interpretation
of status ET703 Cruise
control/speed limiter
button.

DIESEL INJECTION
Fault finding – Conformity check13B
13B - 167V3 MR-372-J84-13B250$540.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
CRUISE CONTROL/SPEED LIMITER (CONTINUED)
*ECU: Electronic control Unit
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test Conditions: ENGINE AT IDLE SPEED, COOLANT TEMPERATURE > 80 ˚C.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
3Brake contactET704:Brake switch No. 1- INACTIVE
- ACTIVE (brake
pedal depressed)In the event of a fault,
consult the interpretation
of status ET704 Brake
switch no. 1
4ET705: Brake switch No. 2- ACTIVE (brake
pedal released)
- INACTIVEIn the event of a fault,
consult the interpretation
of status ET705 Brake
switch no. 2
5Clutch pedal
switchET405:Clutch pedal switch- ACTIVE
- INACTIVEIn the event of a fault,
consult the interpretation
of status ET405 Clutch
switch.
6Cruise control
setpointPR130:Cruise control
setpointIndicates the
reference values
requested by the
driver (in mph (km/h))NONE
7Vehicle speedPR089:Vehicle speed0 mph
Gives the vehicle
speed in mph (km/h).
This parameter is
transmitted by the
ABS computer or
vehicle speed ECU*.
This signal is
transmitted to the
injection system on
the multiplex network.Test the multiplex
network. See fault finding
for the ABS system or the
vehicle speed ECU*.

DIESEL INJECTION
Fault finding – Conformity check13B
13B - 168V3 MR-372-J84-13B250$540.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
CRUISE CONTROL/SPEED LIMITER (continued 2)
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test Conditions: ENGINE AT IDLE SPEED, COOLANT TEMPERATURE > 80 ˚C.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
8Cruise control/
speed limiter
deactivationET415:Cruise control/speed
limiter
deactivationNONE: This status is
present on the diagnostic
tool when:
The computer has been
reinitialised.
The computer has been
reprogrammed.
- STATUS 1: Traction
control request
- STATUS 2: Brake pedal
depressed.
- STATUS 3: Clutch pedal
depressed.
- STATUS 4: Cancel
button pressed
- STATUS 5: Cruise
control or speed limiter
monitoring.
- STATUS 6: Gear lever
in neutral (manual
gearbox) or neutral
position (automatic
transmission).
- STATUS 7:
Inconsistency between
the request and the
vehicle speed.
- STATUS 8: Automatic
transmission in defect
mode.
- STATUS 9: Vehicle
speed monitoring.
- STATUS 10: Monitoring
by injection computer.In the event of a fault,
consult the
interpretation of status
ET415 Cruise control/
speed limiter
deactivation.

DIESEL INJECTION
Fault finding – Status summary table13B
13B - 171V3 MR-372-J84-13B250$585.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51DIESEL INJECTION
Fault finding – Status summary table
Tool status Diagnostic tool title
ET001+ After ignition computer feed
ET003Engine immobiliser
ET004Air conditioning authorisation
ET007Preheating unit control
ET014Monitor cooling fan 1
ET015Monitor cooling fan 2
ET021High speed fan assembly request
ET022Low speed fan assembly request
ET038Engine
ET042Cruise control/speed limiter
ET076Starting
ET077Impact detected
ET079Air conditioning present
ET088Compressor actuation request
ET104Injector code use
ET111Set number of passenger compartment heating resistors (RCH)
ET112Passenger compartment heating resistor cut-off
ET123Brake contact signal no. 2
ET233Clutch pedal
ET238Synchronisation
ET341Immobiliser code programmed
ET405Clutch pedal switch
ET415Deactivation of cruise control/speed limiter
ET589Electric coolant pump control (turbocharger)
ET651EGR programming cut-off
ET703Cruise control/speed limiter buttons
ET704Brake switch no. 1
ET705Brake switch no. 2
MR-372-J84-13B250$585.mif

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 181V3 MR-372-J84-13B250$630.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET042
CRUISE CONTROL/SPEED LIMITER
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
NOT DETECTEDIf the vehicle is not fitted with cruise control/speed limiter function buttons, status ET042
is permanently NOT DETECTED. This confirms that the cruise control/speed limiter
function is not present on the vehicle.
If the vehicle is fitted with cruise control or speed limiter function buttons, the main switch
is in rest (or neutral) position and the injection computer has just been programmed or
reprogrammed, then status ET042 is NOT DETECTED.
To activate the cruise control or speed limiter function, press the main switch in the cruise
control position and then in the speed limiter position.
Return to rest position.
The tool displays status ET042: INACTIVE.
If not, several steps must be checked:
1 - Return to the page about testing the multiplex network with the CLIP program.
Repeat the multiplex network test. Re-establish dialogue with the injection computer.
Check status ET042. If ET042 is INACTIVE, the injection computer has detected the
various positions of the main switch. The cruise control/speed limiter is active.
2 - If status ET042 is still NOT DETECTED, check that the owner of the vehicle has not,
sometime in the past, asked for the cruise control/speed limiter function to be
deactivated. Contact the Techline.
AFTER REPAIRSwitch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
EDC16_V51_ET042

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 182V3 MR-372-J84-13B250$630.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET042
CONTINUED 1
INACTIVEWhen the main switch is in rest position (or neutral), status ET042 is "INACTIVE".
If "CRUISE CONTROL" or "SPEED LIMITER" appears despite the main button being in
the rest position (or neutral), carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for + 12 V APC on the main switch connector.
–Connection code AP43 of component 1081 (Mégane II)
–Connection code AP43 of component 1546 (Scénic II)
Disconnect the main switch and with it in the rest position, check the insulation between:
–Connection codes AP43 and 3FX of component 1081 (Mégane II)
–Connection codes AP43 and 3PD of component 1081 (Mégane II)
–Connection codes AP43 and 3FX of component 1546 (Scénic II)
–Connection codes AP43 and 3PD of component 1546 (Scénic II)
Check the continuity between connections AP43 and 3PD of component 1081
(Mégane II) and component 1546 (Scénic II) in speed limiter position.
Check the continuity between connections AP43 and 3FX of component 1081
(Mégane II) and component 1546 (Scénic II) in cruise control position.
If these checks are not in order, replace the switch.
Check the insulation, continuity and the absence of interference resistance on the
following connections:
–Connection code 3FX,
–connection code 3PD.
Between components 1081 and 120 (Mégane II)
Between components 1546 and 120 (Scénic II)
Also check the engine management computer connectors.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Repair precautions), repair the wiring, otherwise replace it.
AFTER REPAIRSwitch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 183V3 MR-372-J84-13B250$630.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET042
CONTINUED 2
SPEED LIMITERWhen the driver presses the main switch in the speed limiter position, status ET042
becomes SPEED LIMITER.
If CRUISE CONTROL or INACTIVE appears although the switch was pressed in the
speed limiter position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for + 12 V after ignition feed on the main switch connector.
●Connection code AP43 of component 1081 (Mégane II).
●Connection code AP43 of component 1546 (Scénic II).
Disconnect the main switch and with it in the rest position, check the insulation between:
●Connection code AP43 and 3FX, of component 1081 (Mégane II).
●Connection code AP43 and 3PD, of component 1081 (Mégane II).
●Connection code AP43 and 3FX, of component 1546 (Scénic II).
●Connection code AP43 and 3PD, of component 1546 (Scénic II).
–Check the continuity between connections AP43 and 3PD of component 1081
(Mégane II) and component 1546 (Scénic II) in speed limiter position.
–Check the continuity between connections AP43 and 3FX of component 1081
(Mégane II) and component 1546 (Scénic II) in cruise control position.
If these checks show incorrect values, replace the main switch.
Check the insulation, continuity and the absence of interference resistance on the
following connections:
●Connection code 3FX,
●Connection code 3PD,
between components 1081 and 120 (Mégane II).
between components 1546 and 120 (Scénic II).
Also check the engine management computer connectors.
If there is a repair method (See Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRSwitch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 184V3 MR-372-J84-13B250$630.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET042
CONTINUED 3
CRUISE CONTROLWhen the driver presses the main switch in the cruise control position, status ET042
becomes CRUISE CONTROL.
If SPEED LIMITER or INACTIVE appears although the driver pressed the switch in the
cruise control position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
Check for + 12 V after ignition feed on the main switch connector.
●Connection code AP43 of component 1081 (Mégane II).
●Connection code AP43 of component 1546 (Scénic II).
Disconnect the switch and when it is in the rest position, check the insulation between:
●Connection code AP43 and 3FX, of component 1081 (Mégane II).
●Connection code AP43 and 3PD, of component 1081 (Mégane II).
●Connection code AP43 and 3FX, of component 1546 (Scénic II).
●Connection code AP43 and 3PD, of component 1546 (Scénic II).
–Check the continuity between connections AP43 and 3PD of component 1081
(Mégane II) or component 1546 (Scénic II) in speed limiter position.
–Check the continuity between connections AP43 and 3FX of component 1081
(Mégane II) or component 1546 (Scénic II) in cruise control position.
If these checks show incorrect values, replace the main switch.
Check the insulation, continuity and the absence of interference resistance on the
following connections:
●Connection code 3FX,
●connection code 3PD.
Between components 1081 and 120 (Mégane II).
Between components 1546 and 120 (Scénic II).
Also check the engine management computer connectors.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Repair precautions), repair the wiring, otherwise replace it.
AFTER REPAIRSwitch off the ignition and carry out a road test followed by a test with the diagnostic
tool.