2009 Peugeot 607 Dag engine
[x] Cancel search: enginePage 100 of 182
8
85
When the vehicle is
being driven, the res-
pective illumination of
these warning lights
on the instrument pa-
nel, accompanied by an audible signal
and a message on the multifunction dis-
play, indicates that the handbrake is still
on or has not been properly released.
When parking on a slope, direct
your wheels towards the pave-
ment and pull the handbrake.
HANDBRAKE
Releasing
Pull on the handle and press the button
to release the handbrake.
6-SPEED MANUAL GEARBOX
Starting the vehicle
Before starting your vehicle:
- ensure that the gear lever is in neutral,
or
- if a gear is engaged, press the clutch pedal.
Applying
Pull the handbrake to immobilise your
vehicle.
Reverse
To change to reverse gear, lift the ring
under the gear lever knob and push
the gear lever to the left then to the
front.
Reverse gear can only be engaged
when the vehicle is stationary with
the engine idling.
When the ignition is on with
the engine off, always select
neutral.
IGNITION SWITCH
1. Stop position.
2. Running position.
3. Starting position.
The PC Com can be switched
on with the ignition off for a
combined duration of approxi-
mately thirty minutes.
A heavy object (key ring...), attached
to the key and weighing down on its
shaft in the switch, may cause a mal-
function.
Page 101 of 182
8
86
"PORSCHE TIPTRONIC
SYSTEM" AUTOMATIC
GEARBOX
Gear selection gate
Move the lever in the gate to select
a position.
The indicator light corresponding to
the position selected appears on the
instrument panel screen.
Starting the engine
with the handbrake on, select posi-
tion P or N in the gate,
turn the ignition key.
Moving Off
With the engine running, from posi-
tion P :
to exit position P, it is essential
to press the brake pedal,
select position R , D or M , then gra-
dually release the pressure on the
brake pedal; the vehicle moves off
immediately.
To move off from position N :
with your foot on the brake, release
the handbrake,
select position R , D or M , then gra-
dually release the pressure on the
brake pedal; the vehicle moves off
immediately.
When the engine is at idle,
brakes not applied, if position
R , D or M is selected, the ve-
hicle moves even without the
accelerator being pressed.
Do not leave children unsupervised
inside the vehicle, with position
R, D or M selected, with the engi-
ne running, as the vehicle moves
even without the accelerator being
pressed.
The six speed automatic gearbox of-
fers, as required, the comfort of the
automatic program, enhanced by a
manual selection suited to dynamic
driving conditions: Sport program.
Driving on a slippery road is detected
automatically.
However, manual selection is still pos-
sible using the gear lever.
P ark: to immobilise the vehicle and to
start the engine, with the handbrake
on.
R everse: to reverse (select this posi-
tion with the vehicle stationary, engine
at idle).
N eutral: to start the engine and to park,
with the handbrake on.
Note: if position N is inadvertently
engaged while driving, allow the en-
gine to return to idle before engaging
position D then accelerate.
D rive: to drive in automatic mode.
M anual: to drive selecting the gears.
S : Sport program.
Page 102 of 182
8
87
With the ignition off, if the lever
is not in position P , an audible
signal is heard when the dri-
ver's door is opened. Move
the lever to position P . The audible si-
gnal ceases.
When maintenance operations need
to be carried out with the engine run-
ning, apply the handbrake and select
position P .
When the engine is cold, the operation
of the gearbox may differ from its ope-
ration when the engine is warm.
It is only possible to change
from one gear to another if
the vehicle speed and engine
speed permit. If they do not,
the vehicle will operate temporarily in
automatic mode.
When the vehicle is stationary or
moving very slowly, the gearbox auto-
matically selects gear M1 .
Program S (Sport) does not operate in
manual gear selection mode. Operation with manual selection of the gears
select position M in the gate,
push the lever to the + sign to
change up a gear and push again
to change up another gear,
pull the lever to the - sign to chan-
ge down a gear and pull again to
change down another gear.
You can change from position D (dri-
ving in automatic mode) to position M
(driving in manual mode) at any time.
The Drive program
Select position D in the gate: the
gearbox operates in automatic
mode.
The gearbox automatically adapts the
g e a r i n r e l a t i o n t o t h e p r o fi l e o f t h e
road and the vehicle load.
To obtain maximum acceleration wi-
thout touching the lever (kick down),
press the accelerator down fully to the
end of its travel (passing the point of
resistance). The program will change
down automatically or will stay in
the gear selected until the maximum
engine speed is reached.
The program selected is displayed on
the instrument panel screen.
Press button S once the vehicle
has been started in position D , this
program favours dynamic driving.
You can deactivate the Sport program
at any time by pressing the button
selected. Never select position
N when
the vehicle is moving.
Never select positions P or R
unless the vehicle is stationary.
When the ignition is on with the engine
off, always select position P or N .
When travelling downhill, the program
will change down automatically in or-
d e r t o o f f e r e f fi c i e n t e n g i n e b r a k i n g
and good resumption of acceleration.
When travelling uphill, following rapid
releasing of the pedal, the gearbox
maintains the gear engaged to make
acceleration easier.
Page 106 of 182
8
90
Changing a memorised speed
To memorise a speed higher than the
previous one, there are two options:
Without using the accelerator:
press button 3 ;
A brief press increases by 1 mph (1 km/h).
A maintained press increases in steps
of 5 mph (5 km/h).
Using the accelerator:
exceed the memorised speed until
the required speed is reached,
press button 2 or 3 .
To memorise a speed lower than the
previous one:
press button 2 ;
A brief press decreases by 1 mph
(1 km/h).
A maintained press decreases in steps
of 5 mph (5 km/h).
Reactivating the memorised speed
After cancellation, press button
4 . Your
vehicle will return to the last memorised
speed. The display indicates (e.g. at
70 mph (110 km/h)): Cancelling the memorised speed
When the vehicle is stationary, af-
ter the ignition has been switched
off, the system no longer stores
any speed.
Operating check
In the event of a cruise control malfunc-
tion, the memorised speed is erased,
t h e d a s h e s fl a s h f o r a f e w s e c o n d s :
Do not use the cruise control
on slippery roads or in heavy
t r a f fi c .
Contact a PEUGEOT dealer to have
the system checked. This prevents the vehicle speed ex-
ceeding the speed programmed by
the driver (minimum speed of 18 mph
(30 km/h)).
The operations must be carried out:
- while stationary, with the engine
running,
or
- while the vehicle is moving.
Speed limiter function
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned
correctly,
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
Page 107 of 182
8
90
Changing a memorised speed
To memorise a speed higher than the
previous one, there are two options:
Without using the accelerator:
press button 3 ;
A brief press increases by 1 mph (1 km/h).
A maintained press increases in steps
of 5 mph (5 km/h).
Using the accelerator:
exceed the memorised speed until
the required speed is reached,
press button 2 or 3 .
To memorise a speed lower than the
previous one:
press button 2 ;
A brief press decreases by 1 mph
(1 km/h).
A maintained press decreases in steps
of 5 mph (5 km/h).
Reactivating the memorised speed
After cancellation, press button
4 . Your
vehicle will return to the last memorised
speed. The display indicates (e.g. at
70 mph (110 km/h)): Cancelling the memorised speed
When the vehicle is stationary, af-
ter the ignition has been switched
off, the system no longer stores
any speed.
Operating check
In the event of a cruise control malfunc-
tion, the memorised speed is erased,
t h e d a s h e s fl a s h f o r a f e w s e c o n d s :
Do not use the cruise control
on slippery roads or in heavy
t r a f fi c .
Contact a PEUGEOT dealer to have
the system checked. This prevents the vehicle speed ex-
ceeding the speed programmed by
the driver (minimum speed of 18 mph
(30 km/h)).
The operations must be carried out:
- while stationary, with the engine
running,
or
- while the vehicle is moving.
Speed limiter function
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned
correctly,
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
Page 111 of 182
9
95
BONNET
Closing
Lower the bonnet and release it at
the end of its travel.
Check that it is locked.
RUNNING OUT OF FUEL
(DIESEL)
If you should run out of fuel, it is nec-
essary to re-prime the circuit.
If the engine does not start after
15 seconds, repeat the repriming ope-
ration.
Opening
Pull the lever, located on the left
beneath the dashboard, down-
wards.
Lift the catch and raise the bonnet.
Bonnet struts open the bonnet and
keep it open.
2 litre 16V HDI engine
- fi l l t h e f u e l t a n k w i t h a t l e a s t fi v e l i - tres of diesel,
- unclip the style cover to gain ac- cess to the repriming pump,
- unscrew the degas screw,
- squeeze and release the manual repriming pump until diesel is seen
escaping via the degas screw,
- retighten the degas screw,
- operate the starter until the engine starts.
2.7 litre 24V V6 HDI engine
- fi l l t h e f u e l t a n k w i t h a t l e a s t fi v e l i -tres of diesel,
- switch on the ignition and wait 15 seconds before operating the
starter.
Page 112 of 182
9
96
2 LITRE HDI 16V TURBO
DIESEL ENGINE
1. Windscreen/headlamp wash
reservoir.
2. Power steering reservoir.
3. Coolant reservoir.
4. Dipstick.
5. E n g i n e o i l fi l l e r c a p .
6. A i r fi l t e r .
7. Fuse box.
8. B r a k e a n d c l u t c h fl u i d r e s e r v o i r .
9. Priming pump.
10. Degas screw.
Page 113 of 182
9
97
2.7 LITRE V6 24V HDI DIESEL
ENGINE
1. Windscreen/headlamp wash
reservoir.
2. Power steering reservoir.
3. Coolant reservoir.
4. Dipstick.
5. E n g i n e o i l fi l l e r c a p .
6. A i r fi l t e r .
7. Fuse box.
8. B r a k e fl u i d r e s e r v o i r .