2009 Peugeot 607 Dag service
[x] Cancel search: servicePage 24 of 182
1
27
Service warning light
Display of this warning light,
accompanied by an audible
signal and a message on the
multifunction display, indicates
either:
- a fl a t r e m o t e c o n t r o l b a t t e r y ,
- an engine management system fault.
I n t h e fi r s t c a s e , r e p l a c e t h e r e m o t e
control battery.
In the second case, contact a PEUGEOT
dealer as soon as possible.
T y r e u n d e r - i n fl a t i o n
system warning light
Display of this warning light
is accompanied by an au-
dible signal and a message
on the multifunction display indicating
and locating the cause of the warning:
- a fl a t u n d e r - i n fl a t i o n s e n s o r b a t t e r y ,
- a f a u l t y u n d e r - i n fl a t i o n s e n s o r ,
- a m i s s i n g u n d e r - i n fl a t i o n s e n s o r .
Consult a PEUGEOT dealer. Automatic gearbox
warning light
Display of this warning light
is accompanied by an audi-
ble signal and a message on
the multifunction display.
It comes on if there is an abnormality
in the automatic gearbox.
The gearbox will continue to operate in
downgrade mode (locked in 3rd gear).
Consult a PEUGEOT dealer.
Speed control system
warning light
Display of this warning light
is accompanied by an audi-
ble signal and a message on
the multifunction display.
It comes on if there is a malfunction of
the cruise control or speed limiter.
Consult a PEUGEOT dealer.
Parking assistance
system warning light
Display of this warning light
is accompanied by an audi-
ble signal and a message on
the multifunction display.
I n r e v e r s e g e a r o r i n f o r w a r d g e a r a t
a speed below 6 mph (10 km/h), it
comes on if there is a malfunction of
the parking assistance system.
Consult a PEUGEOT dealer.
Page 30 of 182
1
31
SERVICE INDICATOR
T h i s i s a v i s u a l r e m i n d e r o f w h e n t h e
n e x t s e r v i c e i s d u e . T h i s s e r v i c e i s t o
be carried out according to the manu-
f a c t u r e r ' s s e r v i c i n g s c h e d u l e .
T h e p o i n t a t w h i c h t h e s e r v i c e i s d u e i s
calculated from the last indicator zero
reset. It is determined by two param-
eters:
- t h e d i s t a n c e t r a v e l l e d ,
- the time elapsed since the last s e r v i c e .
Note: the distance remaining before
t h e n e x t s e r v i c e i s d u e m a y b e w e i g h t -
ed by the time factor.
T h e s e r v i c e i n f o r m a t i o n a p p e a r s o n
the display, located in the speedo-me-
ter dial, at the same time as the en-
g i n e o i l l e v e l o n t h e i n s t r u m e n t p a n e l
display.
Operation
As soon as the ignition is switched on
and for 7 seconds, the spanner sym-
b o l i s i n g t h e s e r v i c i n g o p e r a t i o n s i s l i t .
The trip recorder display shows the
d i s t a n c e r e m a i n i n g ( i n r o u n d fi g u r e s )
b e f o r e t h e n e x t s e r v i c e .
Example: 4 , 8 0 0 m i l e s / k m r e m a i n b e -
f o r e t h e n e x t s e r v i c e i s d u e . W h e n t h e
ignition comes on and for 7 seconds
the display indicates:
7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the display
shows the total and trip distances.
The distance remaining before the
next service is less than 500 miles
(1,000 km).
Each time the ignition is switched on
and for 7 seconds, the spanner and
t h e d i s t a n c e fl a s h .
Example: 900 miles/km remain before
t h e n e x t s e r v i c e i s d u e .
When switching on the ignition and for
7 seconds, the display shows:
7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the spanner re-
mains lit.
T h i s i n d i c a t e s t h a t a s e r v i c e s h o u l d b e
carried out shortly. The display shows
the total and trip distances.
Page 31 of 182
1
32
Trip recorder zero reset button
Lighting rheostat button
With the ignition on, press the button
until the zeros appear.
With the headlamps on, press button B to
increase the brightness of the lighting of
the instruments and controls or button A to
reduce it.
As soon as the lighting reaches the required
l e v e l o f b r i g h t n e s s , r e l e a s e t h e b u t t o n .
7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the spanner re-
mains lit. The display shows the total
and trip distances.
Note: the spanner may also be lit if the
t w o - y e a r i n t e r v a l h a s b e e n e x c e e d e d .
Service indicator zero re-set
The service is overdue.
Each time the ignition is switched on
and for 7 seconds, the spanner and
t h e e x c e s s d i s t a n c e fl a s h .
Example: t h e s e r v i c e i s o v e r d u e b y
3 0 0 m i l e s / k m . T h e s e r v i c e s h o u l d b e
c a r r i e d o u t v e r y s h o r t l y .
When the ignition is switched on and
for 7 seconds, the display shows:
Your PEUGEOT dealer carries out this
o p e r a t i o n a f t e r e a c h s e r v i c e .
H o w e v e r , i f y o u c a r r y o u t t h e s e r v i c e
yourself, the re-set procedure is as fol-
lows:
Switch off the ignition,
Press and hold the trip recorder re-
set button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
After this operation, if you wish
to disconnect the battery, lock
t h e v e h i c l e a n d w a i t f o r a t l e a s t
fi v e m i n u t e s , o t h e r w i s e t h e z e r o
re-set will not be registered.
Page 32 of 182
1
32
Trip recorder zero reset button
Lighting rheostat button
With the ignition on, press the button
until the zeros appear.
With the headlamps on, press button B to
increase the brightness of the lighting of
the instruments and controls or button A to
reduce it.
As soon as the lighting reaches the required
l e v e l o f b r i g h t n e s s , r e l e a s e t h e b u t t o n .
7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the spanner re-
mains lit. The display shows the total
and trip distances.
Note: the spanner may also be lit if the
t w o - y e a r i n t e r v a l h a s b e e n e x c e e d e d .
Service indicator zero re-set
The service is overdue.
Each time the ignition is switched on
and for 7 seconds, the spanner and
t h e e x c e s s d i s t a n c e fl a s h .
Example: t h e s e r v i c e i s o v e r d u e b y
3 0 0 m i l e s / k m . T h e s e r v i c e s h o u l d b e
c a r r i e d o u t v e r y s h o r t l y .
When the ignition is switched on and
for 7 seconds, the display shows:
Your PEUGEOT dealer carries out this
o p e r a t i o n a f t e r e a c h s e r v i c e .
H o w e v e r , i f y o u c a r r y o u t t h e s e r v i c e
yourself, the re-set procedure is as fol-
lows:
Switch off the ignition,
Press and hold the trip recorder re-
set button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
After this operation, if you wish
to disconnect the battery, lock
t h e v e h i c l e a n d w a i t f o r a t l e a s t
fi v e m i n u t e s , o t h e r w i s e t h e z e r o
re-set will not be registered.
Page 36 of 182
2
36
DT COLOUR AND MAP
SCREEN
This displays the following informa-
tion, via the PC Com control pad:
- the time,
- the date,
- the exterior temperature (the value d i s p l a y e d fl a s h e s i f t h e r e i s a r i s k
of ice),
- t h e a c c e s s e s c h e c k ,
- the vehicle functions warning or status messages, displayed tem-
porarily,
- the audio sources displays,
- the telematic systems displays (telephone, services, ...),
- the trip computer displays,
- t h e c o n fi g u r a t i o n d i s p l a y s ,
- the satellite navigation system dis- plays. Management of the displays
The
"AUDIO" , "NAV" , "TRIP" and
"TEL" buttons on the PC Com control
pad permit displaying in the main win-
dow. E x a m p l e : " C o n fi g u r a t i o n "
" C o n fi g u r a t i o n " m e n u
The brightness of the display
and of the instrument panel
may change when the lights
are switched on automatically.
G e n e r a l m e n u
Press the
"MENU" button to gain
access to the g e n e r a l m e n u and
select one of the following functions:
- "Navigation-Guidance",
- "Audio functions",
- "Trip computer",
- " C o n fi g u r a t i o n " ,
- "Directory",
- "Telematics",
- "Map",
- "Video". This provides access to successive
c o n fi r m a t i o n w i n d o w s .
Example: "TRIP"
Page 61 of 182
4
58
Make a careful note of the
number on each key. The
key number is coded on the
label attached to the key.
If the keys are lost, a PEUGEOT
dealer can rapidly supply you with
new keys.
The high frequency remote control
is a sensitive system; do not oper-
ate it while it is in your pocket as
there is a possibility that it may un-
lock your vehicle, without you being
aware of it.
The remote control does not oper-
ate when the key is in the ignition,
even when the ignition is switched
off, except for reprogramming.
Do not operate the deadlocking
function if there is anyone inside
the vehicle.
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children
on board), remove the ignition key
when you leave the vehicle, even for
a short time.
Do not repeatedly press the button
of your remote control out of range
and out of sight of your vehicle.
You run the risk of stopping it from
working and the remote control
would have to be reprogrammed.
When purchasing a second-hand ve-
hicle, have the key codes memorised
by a PEUGEOT dealer to ensure that
the keys in your possession are the
only ones which can start the vehicle.
D o n o t m a k e a n y m o d i fi c a t i o n s t o
the electronic engine immobiliser
system.
Page 63 of 182
4
58
Make a careful note of the
number on each key. The
key number is coded on the
label attached to the key.
If the keys are lost, a PEUGEOT
dealer can rapidly supply you with
new keys.
The high frequency remote control
is a sensitive system; do not oper-
ate it while it is in your pocket as
there is a possibility that it may un-
lock your vehicle, without you being
aware of it.
The remote control does not oper-
ate when the key is in the ignition,
even when the ignition is switched
off, except for reprogramming.
Do not operate the deadlocking
function if there is anyone inside
the vehicle.
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children
on board), remove the ignition key
when you leave the vehicle, even for
a short time.
Do not repeatedly press the button
of your remote control out of range
and out of sight of your vehicle.
You run the risk of stopping it from
working and the remote control
would have to be reprogrammed.
When purchasing a second-hand ve-
hicle, have the key codes memorised
by a PEUGEOT dealer to ensure that
the keys in your possession are the
only ones which can start the vehicle.
D o n o t m a k e a n y m o d i fi c a t i o n s t o
the electronic engine immobiliser
system.
Page 115 of 182
9
99
CHECKS Handbrake
Where the handbrake travel
is too great or there is a re-
duction in the performance of the
system, the handbrake should be ad-
justed. Have the system checked by a
PEUGEOT dealer.
Only use products recom-
mended by PEUGEOT or
products of equivalent quality
a n d s p e c i fi c a t i o n .
To ensure best performance from
components as important as the pow-
er steering and the braking system,
P E U G E O T s e l e c t s a n d o f f e r s s p e c i fi c
products.
To prevent damage to the electrical
units, high pressure washing of the en-
gine compartment is strictly prohibited .
In order to check the main levels
and certain components, in accord-
ance with the manufacturer's servi-
cing schedule, refer to the pages of
the servicing booklet which corres-
pond to your vehicle's engine. Battery
At the start of winter, have
your battery checked by a
PEUGEOT dealer.
Air filter and passenger compartment filter
H a v e t h e fi l t e r e l e m e n t s r e -
placed regularly. If you drive
in dusty conditions, change them
twice as often .
Particulate emission filter - Additive reservoir (Diesel)
Maintenance of the particulate emis-
s i o n fi l t e r a n d fi l l i n g o f t h e a d d i t i v e
reservoir must be carried out by a
PEUGEOT dealer, according to the
manufacturer's servicing schedule.
Brake pads
Brake pad wear depends on
the style of driving, in particu-
lar for vehicles which are used in town,
over short distances.
Manual gearbox
This does not need an oil change.
Have the level checked, according to
the manufacturer's servicing schedule.
Automatic gearbox
This does not need an oil change. Have
the level checked by a PEUGEOT
dealer, according to the manufacturer's
servicing schedule.
Oil filter
C h a n g e t h e fi l t e r r e g u l a r l y , i n a c c o r d -
ance with the servicing schedule.
It may be necessary to check
the thickness of the pads,
even between services.
Disc wear condition
For any information relating to check-
ing of the disc wear condition, contact
a PEUGEOT dealer.