2009 Peugeot 607 Dag check engine
[x] Cancel search: check enginePage 12 of 182
Instrument panel and warning lights Controls bar
A. When the ignition is on, the fuel
gauge needle should rise.
B. When the engine is running, its
associated low fuel level warning
light should switch off.
C. When the ignition is on, the display
should indicate "CHECK OK" ,
"OIL OK" , "Pressure OK" for a few
seconds.
If the messages are not correct, refer to
the corresponding section.
When the ignition is on, the orange and
red warning lights come on.
When the engine is running, these
warning lights should switch off.
If warning lights remain on, refer to the
page concerned. Lighting of the indicator light indicates the
status of the corresponding function.
19
88
A. Selection of the electronically con-
trolled suspension.
B. Deactivation of the visual and audible
rear and front parking assistance.
C. Sunroof control.
D. Rear blind control.
92
67
75
Energy economy mode
110 110
After the engine has stopped, certain
electrical functions can only be used for
a limited combined duration, to prevent
discharging of the battery.
Once this period has elapsed, the active
functions are put on standby.
In order to exit the energy economy
mode and resume the use of these
functions immediately, the engine must
be started and left running for a few
minutes.
If the engine has been running for at
least 10 minutes, the functions are ac-
tive for 30 minutes.
If the engine has been running for less
than 10 minutes, this duration before re-
turning to economy mode is 5 minutes.
If the doors or boot are opened several
times or if the alarm is triggered, this
may result in activation of the energy
economy mode.
Page 16 of 182
1
19
DIESEL MANUAL AND AUTOMATIC GEARBOXES
INSTRUMENT PANEL
1. Engine oil temperature indicator.
2. H a n d b r a k e , l o w b r a k e fl u i d l e v e l a n d
electronic brake force distribution
warning light.
3. Seat belt not fastened/unfastened
warning light.
4. Dipped headlamps indicator light.
5. Main beam headlamps indicator
light.
6. Lighting rheostat buttons.
7. R e v c o u n t e r .
8. Anti-lock braking system (ABS)
warning light.
9. Diesel engine pre-heating warning
light.
10. Emission control system warning
light.
11. Left direction indicator.
12. L o w f u e l l e v e l w a r n i n g l i g h t .
13. Fuel gauge.
14. Functions display screen:
- Check.
- E n g i n e o i l l e v e l g a u g e .
- Warning and status indicator lights.
- Cruise control/speed limiter.
- Automatic gearbox.
- Trip computer.
- S a t e l l i t e n a v i g a t i o n s y s t e m .
15. Right direction indicator.
16. Speedometer.
17. S e r v i c e i n d i c a t o r , t o t a l a n d t r i p
distance recorders.
18. Trip distance recorder zero reset
button.
19. Manual check button.
20. Rear fog lamps indicator light.
21. Front fog lamps indicator light.
22.
Passenger air bag disarmed warning light *
23. Coolant temperature indicator.
* According to country.
Page 18 of 182
1
21
Seat belt not fastened/
unfastened warning light
W i t h t h e v e h i c l e s t a t i o n a r y ,
when the ignition is switched
on, the warning light comes
o n i f t h e d r i v e r a n d / o r t h e
front passenger has not fas-
tened his seat belt.
From approximately 12 mph (20 km/h)
and for two minutes, the warning light
fl a s h e s a c c o m p a n i e d b y a n i n c r e a s -
ingly loud audible signal. Once these
t w o m i n u t e s h a v e e l a p s e d , t h e w a r n -
i n g l i g h t r e m a i n s o n u n t i l t h e d r i v e r o r
front passenger fastens his seat belt.
W h e n t h e v e h i c l e i s m o v i n g , t h e w a r n -
i n g l i g h t c o m e s o n i f t h e d r i v e r o r o n e
of the front or rear passengers unfas-
tens his seat belt.
Diesel engine pre-heating
warning light
I f t h e t e m p e r a t u r e i s s u f fi -
cient, the warning light does
not come on and you can
start without waiting.
If the warning light comes on, wait
until it goes out before operating the
starter.
If no malfunction has been
detected: the CHECK OK
indicator light comes on af-
ter two seconds (following a
black screen), in the absence
of indicator lights showing the status
o f v e h i c l e f u n c t i o n s . I f t h e s e i n d i c a t o r
lights are present, the CHECK OK in-
dicator light will come on after these.
You may start your vehicle.
If a "minor" malfunction has been
detected: the warning light for the
faulty function comes on. Certain in-
dicator lights showing the status of
v e h i c l e f u n c t i o n s m a y a l s o c o m e o n ,
followed by the CHECK OK indicator
light.
You can start your vehicle; h o w e v e r ,
contact a PEUGEOT dealer as soon
as possible.
If a "major" malfunction has been
detected: the corresponding warning
light comes on. Certain indicator lights
s h o w i n g t h e s t a t u s o f v e h i c l e f u n c t i o n s
may also come on. The CHECK OK
indicator light does not come on.
Do not start your vehicle. Consult a
PEUGEOT dealer.
Following this, the following information appears on the instrument panel display:
T h e e n g i n e o i l l e v e l a p p e a r s f o r a p -
proximately 7 seconds; at the same
t i m e , t h e s e r v i c e i n d i c a t o r a p p e a r s o n
the display located in the speedometer
dial for approximately 7 seconds.
Then, the status of the tyre pressures is
indicated for approximately 5 seconds.
With the ignition on, the vehicle carries out an automatic test which appears on the instrument panel display:
Page 19 of 182
1
22
Manual test of the vehicle Entering CHECK mode
indicator light
This comes on following
pressing of the "CHECK"
button.
Exiting CHECK mode
indicator light
This comes on at the end of
the CHECK mode. With the engine running and the vehicle moving, the instrument panel display temporarily shows:
- warning lights, when a fault occurs,
- v e h i c l e f u n c t i o n s t a t u s i n d i c a t o r
lights, when a change occurs.
The display of certain warning lights
may be accompanied by an audible
signal and a message on the multi-
function display.
Press the "CHECK" button on the
instrument panel.
Y o u c a n s t a r t a t e s t o f t h e v e h i c l e m a n -
ually, at any time, with the ignition on,
e n g i n e r u n n i n g o r v e h i c l e m o v i n g .
This enables you to know:
- the warnings present,
- the status of the functions which can b e a c t i v a t e d o r d e a c t i v a t e d ( a u t o -
matic wipers, automatic switching
on of the lights, ESP, ...).
The associated warning lights are
displayed in succession on the instru-
ment panel display.
If a warning or a change of status oc-
curs during the CHECK mode, the
corresponding warning light(s) are
displayed during this mode and the
CHECK will cease .
Page 78 of 182
5
69
The timed duration must
also be set, via the multi-
function display "Person-
alisation-Configuration"
menu. Automatic switching on of the lights
Side lights and dipped beam head-
lamps switch on automatically if the
light is poor, or during operation of the
windscreen wipers. They switch off
as soon as the light becomes bright
enough or the windscreen wipers
stop.
In foggy weather or in snow, the bright-
n e s s s e n s o r c a n d e t e c t s u f fi c i e n t l i g h t .
Therefore, the lights will not come on
automatically. If necessary, you must
switch on the dipped headlamps man-
ually.
This function is active when the vehicle is
supplied to the customer.
To switch the function on
or off, use the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
Activation Deactivation.
When this function is activat-
ed, the indicator light on the
instrument panel comes on. When the function is deacti-
vated, the indicator light on the
instrument panel comes on.
Cancellation:
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Manual "follow-me-home" lighting
In the absence of the automatic switching
on of the lights, the manual "follow-me-
home" lighting can be activated.
When you leave your vehicle, the side
lights and dipped headlamps remain
on for approximately 1 minute.
Activation:
switch off the engine,
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
fl a s h t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
If the brightness sensor does not func-
tion correctly , the system activates the
function and the lights come on.
Contact a PEUGEOT dealer to have
the system checked.
Daytime running lamps *
On vehicles which are equipped with day-
time running lamps, the dipped headlamps
come on when the vehicle is started.
This indicator lamp comes on on
the instrument panel screen.
The instruments and controls
(instrument panel, multifunc-
tion screen, air conditioning
control panel...) are only lit
on switching to the automatic lighting
mode or when the lights are switched
on manually.
* According to country.
The brightness of the display
and of the instrument panel
may change when the lights
are switched on automatically.
If your lights have been
switched on manually, turn the
ring back to position
0 , lights
off.
Page 79 of 182
5
69
The timed duration must
also be set, via the multi-
function display "Person-
alisation-Configuration"
menu. Automatic switching on of the lights
Side lights and dipped beam head-
lamps switch on automatically if the
light is poor, or during operation of the
windscreen wipers. They switch off
as soon as the light becomes bright
enough or the windscreen wipers
stop.
In foggy weather or in snow, the bright-
n e s s s e n s o r c a n d e t e c t s u f fi c i e n t l i g h t .
Therefore, the lights will not come on
automatically. If necessary, you must
switch on the dipped headlamps man-
ually.
This function is active when the vehicle is
supplied to the customer.
To switch the function on
or off, use the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
Activation Deactivation.
When this function is activat-
ed, the indicator light on the
instrument panel comes on. When the function is deacti-
vated, the indicator light on the
instrument panel comes on.
Cancellation:
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Manual "follow-me-home" lighting
In the absence of the automatic switching
on of the lights, the manual "follow-me-
home" lighting can be activated.
When you leave your vehicle, the side
lights and dipped headlamps remain
on for approximately 1 minute.
Activation:
switch off the engine,
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
fl a s h t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
If the brightness sensor does not func-
tion correctly , the system activates the
function and the lights come on.
Contact a PEUGEOT dealer to have
the system checked.
Daytime running lamps *
On vehicles which are equipped with day-
time running lamps, the dipped headlamps
come on when the vehicle is started.
This indicator lamp comes on on
the instrument panel screen.
The instruments and controls
(instrument panel, multifunc-
tion screen, air conditioning
control panel...) are only lit
on switching to the automatic lighting
mode or when the lights are switched
on manually.
* According to country.
The brightness of the display
and of the instrument panel
may change when the lights
are switched on automatically.
If your lights have been
switched on manually, turn the
ring back to position
0 , lights
off.
Page 90 of 182
7
78
The switch lights up and the
warning light comes on: the
ASR and ESP systems no
longer have any effect on the
engine operation.
TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP)
These systems are linked and com-
plement the ABS.
The ASR system optimises drive to
prevent the wheels skidding, by act-
ing on the brakes of the drive wheels
and on the engine. It also allows the
directional stability of the vehicle to be
improved on acceleration.
If there is a variation between the tra-
jectory followed by the vehicle and that
required by the driver, the ESP system
automatically acts on the engine and
the brake of one or more wheels, in or-
der to put the vehicle back on course,
within the limits of the laws of physics.
Operation of the ASR and ESP
systems T h e w a r n i n g l i g h t fl a s h e s
when the ASR or ESP is ac-
tivated. Disarming
Reactivation:
Automatic if the ignition is switched
off.
Automatic from 30 mph (50 km/h).
Manual by pressing the switch
again. When a malfunction of the
systems occurs, the switch
l i g h t fl a s h e s a n d t h e w a r n -
ing light comes on, accom-
panied by an audible signal
and a message on the multi-function
display.
Contact a PEUGEOT dealer to have
the system checked.
The ASR/ESP systems offer
exceptional safety in normal
driving, but this should not en-
courage the driver to take extra
risks or drive at high speed.
The correct functioning of these sys-
tems depends on observation of the
manufacturer's recommendations re-
garding the wheels (tyres and rims), the
braking components and the electronic
components, as well as the PEUGEOT
assembly and operation procedures.
After an impact, have the system
checked by a PEUGEOT dealer.
When the ignition is on, the
ASR and ESP systems are
always activated. Operating check
Activation of the ASR and ESP
systems In exceptional conditions (starting a
vehicle which is bogged down, stuck
in snow, on soft ground), it may be ad-
visable to disarm the ASR and ESP
systems, so that the wheels can move
freely and regain grip.
Press the "ESP OFF" switch, lo-
cated under the steering wheel to
the right.
Page 91 of 182
![Peugeot 607 Dag 2009 Owners Manual 7
79
TYRE UNDER-INFLATION
DETECTION
Sensors check the tyre pressure dur-
ing driving and trigger a warning in the
event of malfunction (speed greater
than 15 mph [25 km/h]). Sensor(](/manual-img/29/13178/w960_13178-90.png "Peugeot 607 Dag 2009 Owners Manual 7
79
TYRE UNDER-INFLATION
DETECTION
Sensors check the tyre pressure dur-
ing driving and trigger a warning in the
event of malfunction (speed greater
than 15 mph [25 km/h]). Sensor(")
7
79
TYRE UNDER-INFLATION
DETECTION
Sensors check the tyre pressure dur-
ing driving and trigger a warning in the
event of malfunction (speed greater
than 15 mph [25 km/h]). Sensor(s) not detected
This warning light, accompa-
nied by an audible signal and a
message on the multifunction
display, indicates that under-in-
fl a t i o n d e t e c t i o n i s a b s e n t f r o m
one (or several) tyre(s).
Contact a PEUGEOT dealer to replace
the faulty sensor(s).
Pressure check
With the ignition on and after
the engine oil level, this warn-
ing light comes on to indicate
that the system is measuring
the pressure of the tyres.
Pressure OK This warning light comes on
if all of the tyre pressure val-
ues measured are correct.
If one of the warning lights
described below appears,
refer to the corresponding paragraph.
If none of the lights appear, contact a
PEUGEOT dealer to have the system
checked. U n d e r - i n fl a t e d t y r e
This warning light comes on,
accompanied by an audible
signal and a message on the
multifunction display, locat-
i n g t h e d e fl a t e d t y r e .
Have the tyre pressure checked as
soon as possible.
Puncture
This warning light, accom-
panied by an audible signal
and a message on the multi-
function display locating the
punctured tyre, is followed
by illumination of the STOP-
warning light.
Stop immediately, avoiding any sud-
den movement of the steering wheel
and the brakes.
Change the damaged (punctured or
v e r y d e fl a t e d ) t y r e , a n d h a v e t h e t y r e
pressure checked as soon as possible. All repairs and changing of
t y r e s o n a w h e e l fi t t e d w i t h t h i s
system must be carried out by
a PEUGEOT dealer.
T h e t y r e u n d e r - i n fl a t i o n d e t e c t i o n
system is an aid to driving which
does not replace the need for the
driver to be vigilant or to drive re-
sponsibly.
This system does not remove the ne-
cessity for having the tyre pressure
(including that of the spare wheel)
checked regularly, to ensure optimum
dynamic performance of the vehicle
and to prevent premature wear of the
tyres, particularly in the case of ardu-
ous driving conditions (heavy load,
high speed).
The system may temporarily be disturbed
by radio broadcasts on a frequency close
to it.
Note: if the damaged tyre is
temporarily stored in the boot,
it will again emit this message
to remind you of the necessity
of having it repaired. This will prevent
another warning of the same type be-
ing displayed.
Note: this message is also
displayed when one of the
tyres is away from the vehi-
cle (being repaired) or when a
w h e e l w i t h o u t a s e n s o r i s fi t t e d .