2009 Peugeot 207 Dag Owner's Manual

54
FRONT SEATS
Seat consisting of a seat cushion, seat
back and head restraint which can all
be adjusted to adapt your position for
maximum ease of driving and comfort.
1. Forwards-backwards adjustment

 Lift the control and slide the seat for-
wards or backwards. 2. Driver's or passenger's seat
height adjustment

 Pull the handle upwards or push it
downwards as many times as neces-
sary to obtain the required position. 3. Seat back angle adjustment

 Push the handle towards the rear.

!
!
55
No person or object must prevent
the seat slide from returning to its
initial position; return to this posi-
tion is necessary for the seat to
lock in place.
Take care not to trap the seat belt
to avoid hindering the passage of
the rear passengers.
4. Access to rear seats (3 door)

 Pull the handle to fold the seat back
and move the seat forwards. On re-
positioning, the seat returns to its
initial position. 5. Head restraint height adjustment

 To raise the head restraint, pull it up-
wards.

 To remove the head restraint, press
the lug A and pull the head restraint
upwards.

 To put the head restraint back in po-
sition, locate the stems of the head
restraint in the holes, taking care to
keep them in line with the seat back.

 To lower the head restraint, press
the lug A and the head restraint at
the same time. The head restraint has a frame with
a notch which prevents the head
restraint from lowering; this is a
safety device which provides pro-
tection in the event of an impact.

The adjustment is correct when
the upper edge of the head re-
straint is level with the top of the
head.
Never drive with the head restraints
removed; they must be in place and
correctly adjusted.

!
i
56
REAR SEATS
Bench seat the left-hand part (2/3) or right-hand part (1/3) of which can be folded to adapt the load space in the boot.
Never drive with the head restraints
removed; they must be in place and
correctly adjusted.
Rear head restraints
These have a high position (comfort)
and a low position (rear visibility).
The command for activation of
heating of the seat(s) remains
memorised for two minutes after
the ignition has been switched off.
7. Heated seats switch
With the engine running, the front seats
can be heated separately.

 Use the adjustment dial, placed on
the side of each front seat, to switch
on and select the level of heating re-
quired:
0
: Off.
1
: Low.
2
: Medium.
3
: High.
They can also be removed; to remove them:

 pull the head restraint upwards to
the stop,

 then, press the lug.
6. Armrests (except 3 door)
These can be folded down and are re-
movable.

 To remove them, press the button
located between the armrest and
the side of the seat and pull it.

!
i
56
REAR SEATS
Bench seat the left-hand part (2/3) or right-hand part (1/3) of which can be folded to adapt the load space in the boot.
Never drive with the head restraints
removed; they must be in place and
correctly adjusted.
Rear head restraints
These have a high position (comfort)
and a low position (rear visibility).
The command for activation of
heating of the seat(s) remains
memorised for two minutes after
the ignition has been switched off.
7. Heated seats switch
With the engine running, the front seats
can be heated separately.

 Use the adjustment dial, placed on
the side of each front seat, to switch
on and select the level of heating re-
quired:
0
: Off.
1
: Low.
2
: Medium.
3
: High.
They can also be removed; to remove them:

 pull the head restraint upwards to
the stop,

 then, press the lug.
6. Armrests (except 3 door)
These can be folded down and are re-
movable.

 To remove them, press the button
located between the armrest and
the side of the seat and pull it.

!
i
57
Folding the seat (Saloon)
To fold a rear seat without any risk of
damage to it, always start with the
seat cushion, never the seat back
:

 move the corresponding front seat
forward if necessary,
raise the front of the seat cushion 1 ,
 tilt the seat cushion 1 against the front seat,
check that the seat belt is positioned correctly on the side of the seat back,
Repositioning the seat (Saloon)
When repositioning the rear seat:

 straighten the seat back 3 and
secure it,

 fold back the seat cushion 1 .
 pull control 2 upwards to release the seat back 3 ,
place the head restraints in the low position or remove them if necessary,
 tilt the seat back 3 .
The seat cushion 1 can be removed
to increase the loading volume.

!
i
56
REAR SEATS
Bench seat the left-hand part (2/3) or right-hand part (1/3) of which can be folded to adapt the load space in the boot.
Never drive with the head restraints
removed; they must be in place and
correctly adjusted.
Rear head restraints
These have a high position (comfort)
and a low position (rear visibility).
The command for activation of
heating of the seat(s) remains
memorised for two minutes after
the ignition has been switched off.
7. Heated seats switch
With the engine running, the front seats
can be heated separately.

 Use the adjustment dial, placed on
the side of each front seat, to switch
on and select the level of heating re-
quired:
0
: Off.
1
: Low.
2
: Medium.
3
: High.
They can also be removed; to remove them:

 pull the head restraint upwards to
the stop,

 then, press the lug.
6. Armrests (except 3 door)
These can be folded down and are re-
movable.

 To remove them, press the button
located between the armrest and
the side of the seat and pull it.

!
i
58
Folding the seat (SW)
This operation can be carried out at the rear seats or through the opening rear screen.
To fold a rear seat without any risk of
damage:

 move the corresponding front seat
forward if necessary,

 place the head restraints in the low
position, Check that no object could hinder
the movement of the bench seat,
either above or below.
Repositioning the seat (SW)

 pull the control 1 forward to release
the seat back 2 which folds easily
onto the seat cushion 3 .

 When repositioning the rear seat,
straighten the seat back 2 and lock it.
Check that the red indicator, located at control 1 , is no longer visible.

i
!
59
MIRRORS
Exterior mirrors
Adjustable mirror permitting the lateral
rearward vision necessary when over-
taking or parking. Folding

 from outside: lock the vehicle using
the remote control or the key.

 from inside: with the ignition on, pull
switch A rearwards.
Manual model Adjustment

 Move the lever in all four directions
to direct the mirror correctly.
The folding and unfolding of the ex-
terior mirrors can be deactivated by
a PEUGEOT dealer.
Folding

 When parked, fold the mirror manu-
ally to protect it.
Unfolding

 Before starting, unfold the mirror.
Electric model
Adjustment

 Slide switch A to the right or to the left
to select the corresponding mirror.

 Move knob B in all four directions to
adjust.

 Return switch A to the centre position. Unfolding

 from outside: unlock the vehicle using
the remote control or the key.

 from inside: with the ignition on, pull
switch A rearwards.