2009 Peugeot 207 Dag Owner's Manual

i
143
After changing a wheel
To store the punctured wheel in the
boot correctly, fi rst remove the cen-
tral cover.
Have the tightening of the bolts and
the pressure of the spare wheel
checked by a PEUGEOT dealer
without delay.
Have the punctured wheel repaired
and replace it on the vehicle as
soon as possible.
Fitting the wheel
List of operations

 Put the wheel in place on the hub.

 Screw in the bolts by hand to the
stop.

 Pre-tighten the anti-theft bolt us-
ing the wheelbrace 1 fi tted with the
anti-theft socket 4 (if your vehicle is
equipped with this).

 Pre-tighten the other bolts using the
wheelbrace 1 only.

 Lower the vehicle fully.

 Fold the jack 2 and detach it.

 Lock the anti-theft bolt using the
wheelbrace 1 fi tted with the anti-theft
socket 4 (if your vehicle is equipped
with this).

 Lock the other bolts using the wheel-
brace 1 only.

 Refi t the chromed bolt covers on
each of the bolts.

 Store the tools in the box.

!
i
i
144
CHANGING A BULB
Procedure for the replacement of a
faulty bulb with a new bulb without the
use of tools.
1. Direction indicators
(PY 21 W amber).

2. Side lights (W 5 W).

3. Dipped headlamps (H7-55 W).

4. Main beam headlamps (H1-55 W).

5. Directional headlamps (H7-55 W).

6. Fog lamps (H11-55 W). Changing the direction indicators

 Handle the bulbs with a dry
cloth.
The headlamps are fi tted with poly-
carbonate glass with a protective
coating:

 do not clean them using a dry
or abrasive cloth, or using a
detergent or solvent product,

 use a sponge and soapy water.
In certain climatic conditions (low
temperature, humidity),
conden-
sation on the internal surface of
the glass of the headlamps and
rear lights is normal ; it disap-
pears a few minutes after the lights
are switched on . Model with dipped headlamps with
elliptical module and directional
headlamps
Amber coloured bulbs, such as the
direction indicators, must be re-
placed with bulbs of identical speci-
fi cation and colour.

 Turn the bulb holder one quarter of
a turn and remove it.

 Pull the bulb then change it.
To refi t, carry out these operations in re-
verse order.
Front lights
Model with conventional lights

145
Changing the side lights

 Disconnect the main headlamp con-
nector.

 Remove the plastic protective cover
by pulling on the tab.

 Turn the bulb holder one quarter of
a turn and remove it.

 Pull the bulb and change it.
To refi t, carry out these operations in re-
verse order.
Changing the dipped headlamps,
main beam headlamps or directional
headlamps

 Disconnect the main headlamp con-
nector.

 Remove the corresponding plastic
protective cover by pulling on the
tab.

 Disconnect the connector of the cor-
responding light.

 Move aside the spring to release the
bulb and remove the bulb.
To refi t, carry out these operations in re-
verse order. Changing the integrated direction
indicator side repeaters

 Insert a screwdriver towards the
centre of the repeater between the
repeater and the base of the mirror.

 Tilt the screwdriver to extract the re-
peater and remove the repeater.

 Disconnect the repeater connector.
To refi t, carry out these operations in re-
verse order.
To obtain a replacement repeater, con-
tact a PEUGEOT dealer.
Changing the fog lamps
For replacement of these bulbs, contact
a PEUGEOT dealer.

i
i
146
Rear lights (Saloon)

1. Brake lights (P 21 W).

2. Side lights (diodes).

3. Fog lamps (P 21 W).

4. Direction indicators
(PY 21 W amber).

5. Reversing lights (R 10 W). Changing bulbs
These bulbs (with the exception of the
diode lights) are changed from outside
the boot:

 remove the light fi xing bolt,

 take out the light from the outside,

 disconnect the light connector,

 remove the light seal,

 press the four tabs and remove the
bulb holder,

 turn the bulb one quarter of a turn
and change it.
If the vehicle is fi tted with the JBL
audio system, on the right-hand
side, open the fl ap fi rst to gain ac-
cess to the fi xing bolt.
Amber coloured bulbs, such as the
direction indicators, must be re-
placed with bulbs of identical speci-
fi cation and colour.
For the replacement of diode lights,
consult a PEUGEOT dealer. To refi t, carry out these operations in re-
verse order.

!
147
Changing the third brake light bulbs
(4 bulbs W 5 W)

 Press on the fi xing pins on each side
of the light.

 Take out the light from the outside.

 Turn the bulb holder which corre-
sponds to the faulty bulb one quar-
ter of a turn and remove it.

 Pull the bulb and change it. Changing the number plate light
bulbs (W 5 W)

 Insert a thin screwdriver in one of
the exterior holes of the lens.

 Push it towards the outside to unclip it.

 Remove the lens.

 Pull the bulb and change it.
To refi t, carry out these operations in re-
verse order.
High pressure washing
When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the lights and their
surrounds to avoid damaging their
varnish and their seal.

i
148
Rear lights (SW)

1. Brake lights (P 21 W).

2. Side lights (R 5 W).

3. Direction indicators
(PY 21 W amber).

4. Fog lamps (P 21 W).

5. Reversing lights (R 10 W). Changing bulbs
These fi ve bulbs are changed from out-
side the boot:

 remove the access fl ap,

 disconnect the light connector,

 remove the light fi xing bolt,

 take out the light from the outside,

 press on the four tabs and remove
the bulb holder,

 turn the bulb a quarter of a turn and
change it.
To refi t, carry out these operations in re-
verse order.
Take care to engage the light in its
guides keeping it in the centreline of the
vehicle.
Tighten the fi xing bolt suffi ciently by
hand to guarantee the sealing of the
light.
Amber coloured bulbs, such as the
direction indicators, must be replaced
with bulbs of identical specifi cation
and colour.

!
149
Changing the third brake light bulbs
(4 bulbs W 5 W)

 Remove the two light fi xing nuts.

 Take out the light from the outside.

 Press on the two tabs and remove
the bulb holder

 Pull the bulb and change it.
To refi t, carry out these operations in re-
verse order.
Tighten the fi xing bolt suffi ciently by
hand to guarantee the sealing of the
light. Changing the number plate bulbs
(W 5 W)

 Insert a thin screwdriver into one of
the exterior holes of the lens.

 Push it towards the outside to unclip it

 Remove the lens.

 Pull the bulb and change it.
High pressure washing
When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the lights and their
surrounds to avoid damaging their
varnish and their seal.

!
i
150
PEUGEOT does not accept any
responsibility for the costs incurred
in repairing your vehicle or for the
malfunctions resulting from the in-
stallation of additional accessories
which are not supplied or recom-
mended by PEUGEOT and which
are not installed in accordance with
its instructions, particularly when
the combined consumption of all
additional equipment connected
exceeds 10 milliamperes.

Installation of electrical accessories
Your vehicle's electrical circuit is
designed to operate with the stand-
ard or optional equipment.
Before installing other electrical
equipment or accessories in your ve-
hicle, contact a PEUGEOT dealer.
CHANGING A FUSE
Procedure for the replacement of a
faulty fuse with a new fuse in order to
rectify a failure of the corresponding
function.
Access to the tools
The extraction pliers are installed on the
back of the fascia fuse box cover.
To gain access to them:

 unclip the cover pulling at the top,

 remove the cover completely,

 remove the pliers. Replacing a fuse
Before replacing a fuse, the cause of
the failure must be identifi ed and recti-
fi ed.

 Identify the faulty fuse by examining
the condition of its fi lament.

 Use the special pliers to extract the
fuse from its housing.

 Always replace the faulty fuse with a
fuse of the same rating.

 Check that the number engraved
on the box and the rating engraved
on the top correspond to the tables
which follow.
Correct

Incorrect