2009 CHERY TIGGO belt

Downloaded from www.Manualslib.com manuals search engine Crankshaft Position (CKP) Sensor
Description
The Crankshaft Position (CKP) sensor is located on the flywheel shell facing the gear teeth of the signal plate. It
detects the fluctuation of the engine revolution. The sensor consists of a permanent magnet and Induction coil.
Operation
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The
changing gap cause the magnetic field near the sensor to change. Due to the changing magnetic field, the voltage
from the sensor changes. The Engine Control Module (ECM) receives the voltage signal and detects the fluctuation
of the engine revolution.
Removal & Installation
1. Disconnect the negative battery cable.
2. Disconnect the crankshaft position sensor electricalconnector from the crankshaft position sensor.
3. Remove the accessory drive belt (See Accessory Drive Belt Removal & Installation in Section 02
Engine).
4. Remove the crankshaft pulley (See Crankshaft Pul- ley Removal & Installation in Section 02 Engine).
5. Remove the timing belt lower cover (See Timing Belt Lower Cover Removal & Installation in Section
02 Engine).
6. Remove the crankshaft position sensor retaining bolts (1).
(Tighten: Crankshaft position sensor retaining bolt
to 20 N·m)
7. Installation is in the order of removal.
ON-VEHICLE SERVICE
LTSM030012
03–542Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 9.CHECK FOR BRAKE SYSTEM CONCERNS
• Check the operation of the brakes.
Is a fault indicated?
Ye s>>Repair as necessary.
No
>>Go to the next step.
10.ADDITIONAL CHECKS
• Check the following for possible additional causes:
Customer driving habits (such as excessive loads or over RPM limiting functions enabled).
Clutch.
Charging system.
Ignition base timing (if not previously checked).
• If the base timing is not correct, align the engine timing belt (See Engine Timing Belt Removal & Installation in
02 Engine).
Are all checks OK?
Ye s>>See Diagnostic Help for additional information.
No
>>Repair as necessary.
Verify the symptom no longer exists.
ELECTRONIC ENGINE CONTROLS - 2.4L ENGINE SYMPTOM DIAGNOSIS
03
03–555Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 5.CHECK KNOCK SENSOR
• Check knock sensor.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair as necessary.
Verify the symptom no longer exists.
6.CHECK TIMING
• Check for the timing misalignment.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Align the engine timing belt (See Engine Timing Belt Removal & Installation in Section 02 Engine).
7.CHECK FUEL SYSTEM PRESSURE
• Release the fuel system pressure (See Fuel Pressure Relief Procedure in Section 04 Fuel Delivery).
• Check fuel system pressure (See Fuel Pressure Test in Section 04 Fuel Delivery).
Is fuel pressure correct?
Ye s>>Go to the next step.
No
>>If the fuel pressure is greater than 400 kPa (4.0 bar):
Replace the fuel pressure regulator.
If the fuel pressure is less than 400 kPa (4.0 bar):
Check the fuel supply system for restrictions or leaks.
If no problems, repair or replace fuel filter, pressure regulator or fuel pump assembly.
8.CHECK FOR BASE ENGINE CONCERNS
• Check for base engine concerns (such as improper cylinder compression, worn camshaft/valve train, gasket
leaks).
Is a fault indicated?
Ye s>>Repair as necessary.
No
>>See Diagnostic Help for additional information.
ELECTRONIC ENGINE CONTROLS - 2.4L ENGINE SYMPTOM DIAGNOSIS
03
03–557Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine GENERAL INFORMATION
Description
The generator is belt-driven by the engine. It is serviced only as a complete assembly. If the generator fails for any
reason, the entire assembly must be replaced. The generator produces DC voltage.
Operation
As the energized rotor begins to rotate within the generator, the spinning magnetic field induces a current into the
windings of the stator coil.
The Y-type stator winding connections deliver the induced AC current to 3 positive and 3 negative diodes for recti-
fication. From the diodes, rectified DC current is delivered to the vehicle’s electrical system through the generator,
battery, and ground terminals. 1.6L & 1.8L & 2.0L
2.4L
LTSM050009T
LTSM050008T
05–12Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine DIAGNOSIS & TESTING
Generator Noise
Noise emitting from the generator may be caused by the following:
•Worn, loose or defective bearings
• Loose or defective drive pulley
• Incorrect, worn, damaged or misadjusted drive belt
• Loose mounting bolts
• Misaligned drive pulley
• Defective stator
• Damaged internal fins
05–16Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine ON-VEHICLE SERVICE
Generator
Removal & Installation - 1.6L & 1.8L & 2.0L
1. Disconnect the negative battery cable.
2. Disconnect the generator electrical connector.
3. Remove the engine drive belt (See Drive Belt Removal & Installation in Section 02 Engine).
4. Remove the generator cable nut (1) connecting thepositive cable to the generator.
(Tighten: Generator cable nut to 13 N·m)
5. Remove two generator mounting bolts (1). (Tighten: Generator mounting bolts to 30 N·m)
6. Remove the generator from the engine.
7. Installation is in the reverse order of removal.
BESM050002
BESM050003
05
05–17Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Removal & Installation - 2.4L
1. Disconnect the negative battery cable.
2. Remove the engine drive belt (See Drive BeltRemoval & Installation in Section 02 Engine).
3. Remove the generator cable nut (1) connecting the positive cable to the generator.
(Tighten: Generator cable nut to 10 N·m)
4. Disconnect the electrical connector (2).
5. Remove the two generator adjustment bracket bolts (1).
(Tighten: Generator adjustment bracket bolts to
25 N·m)
6. Remove the generator from the engine.
7. Installation is in the reverse order of removal.
Generator Inspection
1. Start the engine. NOTE: If the battery warning lamp illuminates, there may be a problem with the charging system.
2. With the engine running, check the output voltage of the generator with a digital multimeter (note the voltage).
3. If the voltage is between 14.1 V - 14.7 V, the generator is good.
ON-VEHICLE SERVICE
LTSM050003
LTSM050004
05–18Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Thermostat Inspection
1. Inspect the sealing surface of the thermostat (theseat should be tight at room temperature).
2. Inspect the opening temperature and maximum stroke of the thermostat.• Opening temperature of the thermostat is 87°
± 2°C
• Maximum stroke of the thermostat is 8 mm
• Full opening temperature of the thermostat is
104°C
3. Verify the thermostat closes 5°C lower than the opening temperature.
4. If the thermostat fails any of the inspection steps, replace the thermostat.
Coolant Pump
Removal & Installation - 1.6L & 1.8L & 2.0L
WARNING!
Always allow the engine to cool before opening the cooling system. Do not remove the coolant pressure relief
cap when the engine is operating or the cooling system is hot. The cooling system is under pressure; steam and
hot liquid can come out forcefully when the cap is loosened slightly. Failure to follow these instructions may
result in serious personal injury.
1. Drain the cooling system (See Cooling System Draining Procedure in Section 06 Cooling System).
2. Remove the timing belt (See Timing Belt Removal & Installation in Section 02 Engine).
3. Remove the coolant pump mounting bolts (1).(Tighten: Coolant pump mounting bolts to 15 N·m)
4. Remove the water pump and gasket.
5. Installation is in the reverse order of removal.
Installation Notes:
• Install a new coolant pump gasket during installa-
tion (1).
• Verify the cooling system is filled to proper
specifications.
ON-VEHICLE SERVICE
LTSM060014
BESM060001
BESM060002
06–16Chery Automobile Co., Ltd.