2009 CHERY TIGGO belt

Downloaded from www.Manualslib.com manuals search engine ON-VEHICLE SERVICE
Accessory Drive Belt
Removal & Installation
WARNING!
Inspect the drive belt only when the engine is stopped.
1. Loosen the power steering pump adjustment bolt(1).
1 - Power Steering Pump
2 - Crankshaft Pulley
3 - Idler Pulley
4 - A/C Compressor5 - Coolant Pump Pulley
6 - Generator Pulley
7 - A/C Compressor Belt
8 - Generator Belt
LTSM020176
LTSM020185
02
02–167Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 2. Remove the A/C compressor belt.
3. Loosen the generator adjustment bolts (1).
4. Remove the generator belt.
5. Installation is in the reverse order of removal.
Air Cleaner Element
Removal & Installation
1. Loosen the air cleaner case side clamps (1) andraise the air cleaner case (upper).
2. Remove the air cleaner element.
3. Installation is in the reverse order of removal.
ON-VEHICLE SERVICE
LTSM050004
LTSM020239
02–168Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Camshaft
Removal & Installation
NOTE :
The following special tools are required to perform the repair procedure:
•MD-998719 - Camshaft Belt Gear Holder
• MD-990767 - Camshaft Belt Gear Holder
• MD-998443 - Hydraulic Post Keeper
1 - Rocker Shaft Retaining Bolt
2 - Intake Rocker Arm Shaft
3 - Rocker Arm
4 - Rocker Arm
5 - Rocker Shaft Spring
6 - Hydraulic Adjuster
7 - Rocker Arm and Rocker Shaft8 - Exhaust Rocker Arm Shaft
9 - Rocker Arm
10 - Rocker Arm and Rocker Shaft
11 - Camshaft Oil Seal
12 - O-Ring
13 - Camshaft Thrust Plate
14 - Camshaft
ON-VEHICLE SERVICE
LTSM020081
02
02–171Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine •MD-998442 - Hydraulic Post Wiring
• MD-998713 - Camshaft Oil Seal Installer
• MD-998441 - Hydraulic Post Keeper
• MD-998440 - Leak Tester
1. Remove the accessory drive belt (See Accessory Drive Belt Removal & Installation in Section 02 Engine).
2. Remove the engine timing belt (See Engine Timing Belt Removal & Installation in Section 02 Engine).
3. Remove the cylinder head cover (See Cylinder Head Cover Removal & Installation in Section 02 Engine).
4. Using special tools MD-998719 (1) and MB-990767 (2) remove the camshaft timing belt pulley bolt.
(Tighten: Camshaft timing belt pulley bolt to
120 N·m)
5. Remove the camshaft timing belt pulley.
6. Remove the intake and exhaust rocker shaft assembly retaining bolts (2).
(Tighten: Rocker shaft assembly bolts to 32 N·m)
7. Remove the rocker arm and rocker shaft assem- blies.
CAUTION: Before disassembling the rocker arm
and rocker arm shaft assembly, install special
tool MD-998443 (1) as shown in the illustration
to prevent the hydraulic adjusters from drop-
ping into the cylinder head.
8. Remove the camshaft position sensor electrical connector.
9. Remove the camshaft position sensor. (See Camshaft Position Sensor Removal & Installation in Section 03 Elec- tronic Engine Controls).
10. Remove the camshaft thrust plate retaining bolt. (Tighten: Camshaft thrust plate bolt to 19 ± 3 N·m)
11. Remove the O-ring.
12. Remove the camshaft.
13. Installation is in the reverse order of removal.
ON-VEHICLE SERVICE
LTSM020056
LTSM020082
02–172Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Cylinder Head
Removal & Installation
1. Drain the cooling system (See Cooling System Draining and Filling in Section 06 Cooling).
2. Remove the engine timing belt (See Engine Timing Belt Removal & Installation in Section 02 Engine).
3. Remove the cylinder head cover (See Cylinder Head Cover Removal & Installation in Section 02 Engine).
4. Remove the camshafts (See Camshaft Removal & Installation in Section 02 Engine).
5. Remove the intake manifold (See Intake Manifold Removal & Installation in Section 02 Engine).
6. Remove the exhaust manifold (See Exhaust Manifold Removal & Installation in Section 02 Engine).
7. Remove the water pipe and thermostat assembly.
1 - Cylinder Head Bolt
2 - Valve Spring Locks
3 - Upper Valve Spring Retainer
4 - Valve Spring
5 - Valve Oil Seal6 - Lower Valve Spring Retainer
7 - Valve Guide
8 - Valve Seat
9 - Valve
10 - Cylinder Head
ON-VEHICLE SERVICE
LTSM020090
02
02–175Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Front Crankshaft Oil Seal
Removal & Installation
NOTE :
The following special tools are required to perform the repair procedure:
•MD-998778 - Crankshaft Belt Gear Puller
• MD-998781 - Flywheel Holder
1. Remove the accessory drive belt (See Accessory Drive Belt Removal & Installation in Section 02 Engine).
2. Remove the crankshaft vibration damper bolts (1). (Tighten: Crankshaft vibration damper bolts to 25
N·m)
3. Remove the engine timing belt (See Engine Timing Belt Removal & Installation in Section 02 Engine).
4. Install special tool MD-998781 (1), onto the flywheel.
5. Remove the crankshaft timing belt pulley bolt.
6. Using special tool MD-998778 (1), remove the crankshaft timing belt pulley from the crankshaft.
7. Remove the key-way from the crankshaft.
8. Using an appropriate tool, remove the front crankshaft oil seal.
ON-VEHICLE SERVICE
LTSM020153
LTSM020051 LTSM020052
02
02–177Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine CAUTION:
Be careful not to damage the front cover seal surface while removing the seal.
9. Installation is in the reverse order of removal.
Installation Notes:
• Lubricate the new front seal with engine oil prior to assembly.
• Use the front crankshaft seal installer MD-998285 (1), to install the new seal.
• Tighten the crankshaft timing belt pulley bolt in the
following sequence.
1st step: Tighten the crankshaft timing belt
pulley bolt to 130 N·m.
2nd step: Tighten the bolt an additional 65°
ON-VEHICLE SERVICE
LTSM020220
02–178Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 15. Remove the pipe from the canister control valve.
16. Disconnect the heater hoses (1) on the vehicle.
17. Remove the vacuum line from the brake booster.
18. Remove the dipstick.
19. Remove the accessory drive belt (See Accessory Drive Belt Removal & Installation in Section 02 Engine).
20. Remove the A/C compressor high and low pres-sure pipe bolts (1) & (2).
ON-VEHICLE SERVICE
LTSM130010
LTSM130008
02
02–185Chery Automobile Co., Ltd.