2008 RENAULT SCENIC Electrical Equipment - Instrument Panel Workshop Manual

83A-25
MR-372-J84-83A000$441.mif
V8
INSTRUMENT PANEL
Fault finding - Conformity check83A
TDB ph2 (EG/MG)
Prog version: 04xx
Vdiag No.: 08, 0C
TRIP COMPUTER
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Ignition on, engine off.
Order FunctionParameter, Status
Checked or ActionDisplay and notes Fault finding
1Button ET030:Trip computer
scroll buttonAllows the display to
be adjusted.
Released
PressedIn the event of a fault, consult
the interpretation of status
ET030 Trip computer scroll
button.
2
FuelPR112:Fuel flowX l/hIn the event of a fault, consult
the interpretation of parameter
PR112 Fuel flow.
3PR117:Fuel consumed
since TRIP
COMPUTER
RESETX lIn the event of a fault, consult
the interpretation of parameter
PR117 Fuel consumed since
trip computer reset.
4Vehicle
speedPR099:Vehicle speedX mph (km/h)In the event of a fault, consult
the interpretation of parameter
PR099 Vehicle speed.
5Buzzer AC006:BuzzerThe buzzer should
sound.In the event of a fault, consult
the interpretation of command
AC006 Buzzer.

83A-26
MR-372-J84-83A000$504.mif
V8
83A
INSTRUMENT PANEL
Fault finding - Status summary table
Tool status Diagnostic tool title
ET002+ 12 V after ignition
ET030ADAC scroll button
ET062Seat belt alarm
ET066Brake fluid level light alert
ET096Oil pressure contact
ET097Parking brake
ET098Driver's seat belt contact
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$504.mif

83A-27
MR-372-J84-83A000$567.mif
V8
83A
INSTRUMENT PANEL
Fault finding - Interpretation of statuses
TDB_V08_ET002/TDB_V0C_ET002
ET002
+ 12 V AFTER IGNITION
NOTESThere must be no present or stored faults.
Status ET002 + 12 V after ignition must be present.
Run a test on the multiplex network (see 88B, Multiplexing) and the Protection and Switching Unit
(see 87G, Engine compartment connection unit).
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$567.mif

83A-28
MR-372-J84-83A000$567.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
ET030
ADAC SCROLL BUTTON
NOTESThere must be no present or stored faults.
Press the button: the status should be Pressed.
Carry out a test on the multiplex network (see 88B, Multiplexing) and the UCH (see 87B, Passenger
compartment connection unit).
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB_V08_ET030/TDB_V0C_ET030

83A-29
MR-372-J84-83A000$567.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
ET066
BRAKE FLUID LEVEL LIGHT WARNING
NOTESThere must be no present or stored faults.
Check the brake fluid level in the reservoir.
If status ET066 Brake fluid level warning light is PRESENT and the level is correct, disconnect the connector
on the brake fluid reservoir level switch.
If the status ET066 Brake fluid level warning light becomes ABSENT, replace the switch.
Check the insulation and continuity of the connection between:
Grey connector level sensor track 2 track 20 of the instrument panel connector
If there is a repair method (see Technical note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair) repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB_V08_ET066/TDB_V0C_ET066

83A-30
MR-372-J84-83A000$567.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
ET096
OIL PRESSURE CONTACT
NOTESThere must be no present or stored faults.
Check the oil level. Top up if necessary.
Test the Protection and Switching Unit (see 87G, Engine compartment connection unit).
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB_V08_ET096/TDB_V0C_ET096

83A-31
MR-372-J84-83A000$567.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
ET097
PARKING BRAKE
NOTESSpecial notes:
Only apply the checks if the APPLIED and RELEASED statuses are not consistent
with the lever position:
–APPLIED when the lever is released.
–RELEASED when the lever is applied.
STATUS
"APPLIED" when
the lever is
releasedCheck that the handbrake switch is correctly connected and check the condition of the
connections.
Repair if necessary.
With the lever released, check continuity is absent on the following connection:
Handbrake switch track 1 Vehicle earth
If there is continuity, replace the switch.
Check the insulation of the following connection:
Instrument panel track 21 Track 1 of the handbrake switch
If there is a repair method (see Technical note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the wiring, otherwise replace it.
RELEASED
STATUS when the
lever has been
pulled upCheck that the handbrake switch is correctly connected and check the condition of the
connections.
Repair if necessary.
With the lever pulled up, check continuity on the following connection:
Handbrake switch track 1 Vehicle earth
If there is no continuity, replace the switch.
Check the insulation of the following connection:
Instrument panel track 21 Track 1 of the handbrake switch
If there is a repair method (see Technical note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB_V08_ET097/TDB_V0C_ET097

83A-32
MR-372-J84-83A000$567.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
ET098
DRIVER'S SEAT BELT CONTACT
NOTESThere must be no present or stored faults.
Fasten the driver's seat belt: status ET098 Driver's seat belt contact should be
PRESENT and the instrument panel warning light should go out.
Test the multiplex network and the airbag (see 88B, Multiplexing and 88C, Airbag and pretensioners).
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
TDB_V08_ET098/TDB_V0C_ET098