2008 NISSAN TEANA battery replacement

INTELLIGENT KEY BATTERY
DLK-245
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
INTELLIGENT KEY BATTERY
Removal and InstallationINFOID:0000000003795148
1. Release the lock knob at the back of the Intelligent Key and remove the mechanical key.
2. Insert a flat-bladed screwdriver (A) wrapped with a cloth into the
slit of the corner and twist it to separate the upper part from the
lower part.
CAUTION:
 Never touch the circuit board or battery terminal.
 The key fob is water-resistant. However, if it does get wet,
immediately wipe it dry.
3. Replace the battery with new one.
4. Align the tips of the upper and lower parts, and then push them
together until it is securely closed.
CAUTION:
 When replacing battery, keep dirt, grease, and other for-
eign matter off the electrode contact area.
 After replacing the battery, check that all Intelligent Key
functions work normally.
PIIB6221E
Battery replacement :Coin-type lithium battery
(CR2025)
PIIB6222E

EM-6
< PRECAUTION >
PRECAUTIONS
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.
Precaution for Drain Engine Coolant and Engine OilINFOID:0000000003802227
Drain engine coolant and engine oil when the engine is cooled.
Precaution for Disconnecting Fuel PipingINFOID:0000000003802228
 Before starting work, check no fire or spark producing items are in the work area.
 Release fuel pressure before disconnecting and disassembly.
 After disconnecting pipes, plug openings to stop fuel leakage.
Precaution for Removal and DisassemblyINFOID:0000000003802229
 When instructed to use SST, use the specified tools. Always be careful to work safely, avoid forceful or unin-
structed operations.
 Exercise maximum care to avoid damage to mating or sliding surfaces.
 Dowel pins are used for several parts alignment. When replacing and reassembling parts with dowel pins,
check that dowel pins are installed in the original position.
 Cover openings of engine system with a tape or the equivalent, if necessary, to seal out foreign materials.
 Mark and arrange disassembly parts in an organized way for easy troubleshooting and reassembly.
 When loosening nuts and bolts, as a basic rule, start with the one furthest outside, then the one diagonally
opposite, and so on. If the order of loosening is specified, do exactly as specified. Power tools may be used
in the step.
Precaution for Inspection, Repair and ReplacementINFOID:0000000003802230
Before repairing or replacing, thoroughly inspect parts. Inspect new replacement parts in the same way, and
replace if necessary.
Precaution for Assembly and InstallationINFOID:0000000003802231
 Use torque wrench to tighten bolts or nuts to specification.
 When tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with the
ones in center, then ones on inside and outside diagonally in this order. If the order of tightening is specified,
do exactly as specified.
 Replace with new gasket, packing, oil seal or O-ring.
 Dowel pins are used for several parts alignment. When replacing and reassembling parts with dowel pins,
check that dowel pins are installed in the original position.
 Thoroughly wash, clean, and air-blow each part. Carefully check engine oil or engine coolant passages for
any restriction and blockage.
 Avoid damaging sliding or mating surfaces. Completely remove foreign materials such as cloth lint or dust.
Before assembly, oil sliding surfaces well.
 Release air within route when refilling after draining engine coolant.
 After repairing, start the engine and increase engine speed to check engine coolant, fuel, engine oil, and
exhaust gases for leakage.
Precaution for Angle TighteningINFOID:0000000003802232
 Use the angle wrench [SST: KV10112100 (BT8653-A)] for the final tightening of the following engine parts:
- Cylinder head bolts
- Main bearing cap bolts
- Connecting rod cap bolts
- Crankshaft pulley bolt (No the angle wrench is required as bolt flange is provided with notches for angle
tightening)
 Never use a torque value for final tightening.
 The torque value for these parts are for a preliminary step.

EXL-4
OPTICAL SENSOR .........................................185
Exploded View .......................................................185
Removal and Installation .......................................185
LIGHTING & TURN SIGNAL SWITCH ............186
Exploded View .......................................................186
Removal and Installation .......................................186
HAZARD SWITCH ...........................................187
Exploded View .......................................................187
Removal and Installation .......................................187
SIDE TURN SIGNAL LAMP ............................188
Exploded View .......................................................188
Removal and Installation .......................................188
AUTO LEVELIZER CONTROL UNIT ..............190
Exploded View .......................................................190
Removal and Installation .......................................190
REAR COMBINATION LAMP .........................191
Exploded View .......................................................191
Removal and Installation .......................................191
Replacement .........................................................192
HIGH-MOUNTED STOP LAMP .......................193
Exploded View .......................................................193
Removal and Installation .......................................193
REAR FOG LAMP ...........................................194
Exploded View .......................................................194
Removal and Installation .......................................194
Replacement .........................................................194
LICENSE PLATE LAMP ..................................195
Exploded View .......................................................195
Removal and Installation .......................................195
Replacement .........................................................195
SERVICE DATA AND SPECIFICATIONS
(SDS) ..........................................................
197
SERVICE DATA AND SPECIFICATIONS
(SDS) ................................................................
197
Bulb Specifications ................................................197
HALOGEN TYPE
BASIC INSPECTION ..................................
198
DIAGNOSIS AND REPAIR WORKFLOW .......198
Work Flow ..............................................................198
FUNCTION DIAGNOSIS ............................200
HEADLAMP SYSTEM .....................................200
System Diagram ....................................................200
System Description ................................................200
Component Parts Location ....................................201
Component Description ........................................201
AUTO LIGHT SYSTEM ....................................202
System Diagram ....................................................202
System Description ...............................................202
Component Parts Location ...................................203
Component Description ........................................203
FRONT FOG LAMP SYSTEM ..........................204
System Diagram ...................................................204
System Description ...............................................204
Component Parts Location ...................................205
Component Description ........................................205
TURN SIGNAL AND HAZARD WARNING
LAMP SYSTEM ................................................
206
System Diagram ...................................................206
System Description ...............................................206
Component Parts Location ...................................207
Component Description ........................................207
PARKING, LICENSE PLATE AND TAIL
LAMPS SYSTEM ..............................................
208
System Diagram ...................................................208
System Description ...............................................208
Component Parts Location ...................................209
Component Description ........................................209
REAR FOG LAMP SYSTEM ............................210
System Diagram ...................................................210
System Description ...............................................210
Component Parts Location ...................................211
Component Description ........................................211
EXTERIOR LAMP BATTERY SAVER SYS-
TEM ...................................................................
212
System Diagram ...................................................212
System Description ...............................................212
Component Parts Location ...................................213
Component Description ........................................213
DIAGNOSIS SYSTEM (BCM) ...........................214
COMMON ITEM .......................................................214
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) ..................................................
214
HEADLAMP .............................................................215
HEADLAMP : CONSULT-III Function (BCM -
HEAD LAMP) ........................................................
215
FLASHER ................................................................217
FLASHER : CONSULT-III Function (BCM -
FLASHER) ............................................................
217
DIAGNOSIS SYSTEM (IPDM E/R) ...................219
Diagnosis Description ...........................................219
CONSULT-III Function (IPDM E/R) ......................221
COMPONENT DIAGNOSIS ......................224
POWER SUPPLY AND GROUND CIRCUIT ....224
BCM (BODY CONTROL MODULE) ........................224
BCM (BODY CONTROL MODULE) : Diagnosis
Procedure .............................................................
224

FRONT COMBINATION LAMP
EXL-181
< ON-VEHICLE REPAIR >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
Removal and InstallationINFOID:0000000003773620
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
1. Remove the front bumper fascia. Refer to EXT-11, "
Exploded View".
2. Remove the headlamp mounting bolts.
3. Remove the harness clips from the headlamp housing.
4. Pull out the headlamp assembly forward the vehicle.
5. Disconnect the connector before removing the headlamp assembly.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to EXL-173, "
Description".
ReplacementINFOID:0000000003773621
CAUTION:
 Disconnect the battery negative terminal or remove the fuse.
 After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
 Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
 Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB (LO)
1. Remove the fender protector. Keep a service area. Refer to EXT-22, "FENDER PROTECTOR : Exploded
View".
2. Rotate the resin cap counterclockwise and unlock it.
3. Disconnect the bulb socket ground line.
4. Rotate the bulb socket counterclockwise and unlock it.
5. Unlock the retaining spring. And then remove the bulb from the
headlamp housing.
CAUTION:
Never break the xenon bulb ceramic tube when replacing
the bulb.
HEADLAMP BULB (HI)
1. Remove the fender protector. Keep a service area. Refer to EXT-22, "FENDER PROTECTOR : Exploded
View".
2. Disconnect the headlamp (HI) connector.
3. Rotate the bulb counterclockwise and unlock it.
4. Remove the bulb from the headlamp housing.
PARKING LAMP BULB
1. Remove the fender protector. Keep a service area. Refer to EXT-22, "FENDER PROTECTOR : Exploded
View".
2. Rotate the bulb socket counterclockwise and unlock it.
3. Remove the bulb from the parking lamp bulb socket.
FRONT TURN SIGNAL LAMP BULB
JPLIA1089ZZ

FRONT FOG LAMP
EXL-183
< ON-VEHICLE REPAIR >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
FRONT FOG LAMP
Exploded ViewINFOID:0000000003773623
Removal and InstallationINFOID:0000000003773624
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1. Remove the front fender protector. Keep a service area. Refer to EXT-22, "FENDER PROTECTOR :
Exploded View".
2. Remove the front fog lamp connector.
3. Remove the mounting nuts. And then remove the front fog lamp.
NOTE:
Never remove a front fog lamp bracket, when the front fog lamp is replaced.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to EXL-178, "
Description".
ReplacementINFOID:0000000003773625
CAUTION:
 Disconnect the battery negative terminal or remove the fuse.
 Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
 Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
1. Remove the front fender protector. Keep a service area. Refer to EXT-22, "FENDER PROTECTOR :
Exploded View".
1. Front fog lamp bracket 2. Front fog lamp
JPLIA1090ZZ

EXL-192
< ON-VEHICLE REPAIR >[XENON TYPE]
REAR COMBINATION LAMP
Replacement
INFOID:0000000003773636
CAUTION:
 Disconnect the battery negative terminal or remove the fuse.
 Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
 Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP
Replacement integral with rear combination lamp. Refer to EXL-191, "Exploded View".
REAR TURN SIGNAL LAMP BULB
1. Remove the rear combination lamp. Refer to EXL-191, "Exploded View".
2. Rotate the rear turn signal lamp bulb socket counterclockwise, and unlock it.
3. Remove the bulb from the rear turn signal lamp bulb socket.
BACK-UP LAMP BULB
1. Remove the rear combination lamp. Refer to EXL-191, "Exploded View".
2. Rotate the back-up lamp bulb socket counterclockwise, and unlock it.
3. Remove the bulb from the back-up lamp bulb socket.

EXL-194
< ON-VEHICLE REPAIR >[XENON TYPE]
REAR FOG LAMP
REAR FOG LAMP
Exploded ViewINFOID:0000000003774379
Removal and InstallationINFOID:0000000003774380
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1. Disconnect the rear fog lamp connector.
2. Remove the nuts. And then remove the rear fog lamp rim.
3. Remove the screw. And then remove the rear fog lamp from the rear fog lamp rim.
INSTALLATION
Installation is the reverse order of removal.
ReplacementINFOID:0000000003774381
CAUTION:
 Disconnect the battery negative terminal or remove the fuse.
 Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
 Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
REAR FOG LAMP BULB
1. Turn the bulb socket (1) counterclockwise and unlock it.
2. Remove the bulb (2) from the rear fog lamp bulb socket.
1. Rear fog lamp 2. Rear fog lamp bracket 3. Rear fog lamp finisher
JPLIA1102ZZ
JPLIA1103ZZ

LICENSE PLATE LAMP
EXL-195
< ON-VEHICLE REPAIR >[XENON TYPE]
C
D
E
F
G
H
I
J
K
MA
B
EXL
N
O
P
LICENSE PLATE LAMP
Exploded ViewINFOID:0000000003773642
Removal and InstallationINFOID:0000000003773643
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1. Remove the trunk lid finisher inner. Refer to INT-59, "Exploded View".
2. Remove the trunk lid finisher outer. Refer to INT-59, "
Exploded View".
3. Remove the license plate lamp while pushing a resin clip.
4. Disconnect the license plate lamp connector.
INSTALLATION
Install in the reverse order of removal.
ReplacementINFOID:0000000003773644
CAUTION:
 Disconnect the battery negative terminal or remove the fuse.
 Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
 Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
1. Remove the trunk lid finisher inner. Refer to INT-59, "Exploded View".
1. License plate lamp
A. Resin clip
JPLIA1100ZZ