2008 NISSAN TEANA tow

VTL-28
< ON-VEHICLE REPAIR >[WITHOUT 7 INCH DISPLAY]
INTAKE SENSOR
Removal and Installation
INFOID:0000000003774670
REMOVAL
1. Remove evaporator pipe assembly. Refer to HA-54, "Exploded View".
2. Disconnect intake sensor connector.
3. Slide evaporator (1) toward the right side of the vehicle (as
shown in the figure), and then remove intake sensor (2).
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
 Replace O-rings with new ones. Then apply compressor oil to them when installing.
 Mark the mounting position of intake sensor bracket prior to removal so that the reinstalled sensor
can be located in the same position.
 Do not rotate the bracket insertion part when removing and installing the intake sensor.
 Check for refrigerant leakage when charging refrigerant.
37. Defroster door link 38. Foot door link 39. Max. cool door lever
40. Foot door lever 41. Defroster door lever 42. Adapter case
43. Distributor lower case 44. Ventilator door 45. Intake sensor
46. Intake sensor bracket 47. Foot door 48. Max. cool door
49. Defroster door 50. Air mix door (Slide door)
Refer to GI-4, "
Components" for symbols in the figure.
JPIIA0907ZZ

VTL-86
< ON-VEHICLE REPAIR >[WITH 7 INCH DISPLAY]
INTAKE SENSOR
Removal and Installation
INFOID:0000000003894498
REMOVAL
1. Remove evaporator pipe assembly. Refer to HA-54, "Exploded View".
2. Disconnect intake sensor connector.
3. Slide evaporator (1) toward the right side of the vehicle (as
shown in the figure), and then remove intake sensor (2).
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
 Replace O-rings with new ones. Then apply compressor oil to them when installing.
 Mark the mounting position of intake sensor bracket prior to removal so that the reinstalled sensor
can be located in the same position.
 Do not rotate the bracket insertion part when removing and installing the intake sensor.
 Check for refrigerant leakage when charging refrigerant.
37. Defroster door link 38. Foot door link 39. Max. cool door lever
40. Foot door lever 41. Defroster door lever 42. Adapter case
43. Distributor lower case 44. Ventilator door 45. Intake sensor
46. Intake sensor bracket 47. Foot door 48. Max. cool door
49. Defroster door 50. Air mix door (Slide door)
Refer to GI-4, "
Components" for symbols in the figure.
JPIIA0907ZZ

FRONT WASHER NOZZLE AND TUBE
WW-103
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
MA
B
WW
N
O
P
Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking.
ADJUSTMENT
Washer Nozzle Spray Position Adjustment
Adjust spray positions to match the positions shown in the figure.
Unit: mm (in)
JPLIA1139ZZ
1. End of cowl top cover
: Spray area
: Target spray position
Spray position H (Height) L (Width) Spray area
A 293.2 (11.54) 490.7 (19.32)φ 80 (3.15)
B 422.0 (16.61) 298.6 (11.76)φ 80 (3.15)
C 376.2 (14.81) 121.5 (4.78)φ 80 (3.15)
D 327.9 (12.91) 56.3 (2.22)φ 80 (3.15)
E 383.1 (15.08) 300 (11.81)φ 80 (3.15)
F 305.7 (12.04) 475.1 (18.70)φ 80 (3.15)
JPLIA1140ZZ