2008 MITSUBISHI LANCER EVOLUTION X Workshop Manual

WATER PASSAGE
ENGINE COOLING14-3
WATER PASSAGEM2140004000172
NOTE: EGR: Exhaust Gas Recirculation
CVT: Continuously Variable Transmission
WAT E R P U M PM2140003000168
The water pump is the centrifugal, impeller type that
is installed in front of the cylinder block. It is driven by
the drive belt.
AK603624
Water pump
EGR
AB
Thermostat
Radiator Throttle body
CVT oil
coolerHeater
Water pump
EGR
Thermostat
Radiator Throttle body
CVT oil
cooler Heater
AK503034
Impeller
AD
ItemSpecifications
Discharge volume L/min185
Impeller diameter mm (in)62 (2.4)
Pulley outer diameter mm
(in)137 (5.4)

NOTES

13B-1
GROUP 13B
FUEL SUPPLY
CONTENTS
GENERAL INFORMATION . . . . . . . .13B-2FUEL TANK . . . . . . . . . . . . . . . . . . . .13B-3

GENERAL INFORMATION
FUEL SUPPLY13B-2
GENERAL INFORMATIONM2134000100833.The fuel system consists of the following compo-
nents:
•Fuel injector
•Fuel rail
•Fuel pipe
•Fuel tank
•Fuel pump module
•Evaporative emission canister
SPECIFICATIONS
CONSTRUCTION DIAGRAM
This fuel system is designed with consideration for
global environment protection to ensure safety at a
collision, reduce weight, and improve reliability and
quality. This system has the following features:
•A quick-joint connector of a plastic tube is used
for the fuel high-pressure hoses in the engine
compartment to reduce the permeation of fuel
evaporative emission.
•The surface of underfloor fuel pipes is coated
with 1-mm thickness of plastic to improve resis
-
tance to corrosion and chipping.
•A returnless fuel system eliminates returned fuel
from the engine. The heat that fuel receives from
the engine is reduced, minimizing fuel tempera
-
ture in the fuel tank and controlling the amount of
evaporated gas.
ItemSpecification
Fuel tank capacity dm3 (gal)59 (15.5)
Fuel pump typeElectric
Fuel filter typeCartridge (incorporates fuel pump module)
Fuel return systemReturnless
Fuel pump pressure regulator pressure kPa (psi)324 (46)
Fuel injectorTy p eElector-magnetic
Quantity4
Evaporative emission control systemCanister
AC610224
Fuel rail
Fuel injector
Fuel pipeFuel pump moduleEvaporative
emission
canister Fuel tank
AB

FUEL TANK
FUEL SUPPLY13B-3
FUEL TANKM2134001000817.The fuel tank assembly consists of the fuel pump
module, the fuel tank, and so on, and features the
following characteristics:
•The fuel tank is mounted underneath the second
seat to improve safety at a collision.
•The fuel tank itself is made of a pre-coat zinc
alloy galvanised steel sheet that contains no
lead.
•The capacity of the fuel tank is 59 dm3 (15.5 gal)
to meet long-distance drives.
•The fuel cut-off valve, fuel tank leveling valve and
fuel tube have been installed using in-tank con
-
struction to reduce the amount of evaporated fuel
from hoses.
The fuel pump module consists of the following com-
ponents:
•Fuel pump
•Fuel level sensor
•Fuel filter
•Fuel pump pressure regulator
•Fuel tank differential pressure sensor
•Fuel tank temperature sensor
CONSTRUCTION DIAGRAM
AC610225AB
Fuel pump module
Fuel tank
AC610226
Fuel cut-off valve
Fuel check valve
Leveling valve
AC

NOTES

13A-1
GROUP 13A
MULTIPORT FUEL
SYSTEM (MFI)
CONTENTS
GENERAL DESCRIPTION. . . . . . . . .13A-2
CONTROL UNIT. . . . . . . . . . . . . . . . .13A-6
SENSOR. . . . . . . . . . . . . . . . . . . . . . .13A-8
ACTUATOR . . . . . . . . . . . . . . . . . . . .13A-23
FUEL INJECTION CONTROL . . . . . .13A-29
IGNITION TIMING AND CONTROL FOR
CURRENT CARRYING TIME . . . . . .13A-35
THROTTLE VALVE OPENING ANGLE
CONTROL AND IDLE SPEED

CONTROL . . . . . . . . . . . . . . . . . . . . .13A-38
MIVEC (Mitsubishi Innovative Valve
Timing Electronic Control System) .13A-40
MULTIPORT FUEL INJECTION (MFI)
RELAY CONTROL . . . . . . . . . . . . . . .13A-45
FUEL PUMP RELAY CONTROL . . . .13A-46
STARTER RELAY CONTROL . . . . . .13A-47
HEATED OXYGEN SENSOR HEATER
CONTROL . . . . . . . . . . . . . . . . . . . . . .13A-49
A/C COMPRESSOR RELAY
CONTROL . . . . . . . . . . . . . . . . . . . . . .13A-50
GENERATOR CONTROL . . . . . . . . . .13A-51
EVAPORATIVE EMISSION CONTROL
SYSTEM INCORRECT PURGE FLOW
MONITOR . . . . . . . . . . . . . . . . . . . . . .13A-52
EXHAUST GAS RECIRCULATION
CONTROL . . . . . . . . . . . . . . . . . . . . . .13A-53
CONTROLLER AREA NETWORK
(CAN) . . . . . . . . . . . . . . . . . . . . . . . . .13A-53
EVAPORATIVE EMISSION PURGE
CONTROL . . . . . . . . . . . . . . . . . . . . . .13A-53
HC TRAP CATALYTIC CONVERTER
DETERIORATION MONITOR . . . . . . .13A-53
ON-BOARD DIAGNOSTICS . . . . . . . .13A-53

GENERAL DESCRIPTION
MULTIPORT FUEL SYSTEM (MFI)13A-2
GENERAL DESCRIPTIONM2132000101283
Although the control systems are basically the same as those of 2.4L engine used in the GALANT, the follow-
ing improvements have been added.
Improvement / AdditionsRemark
MIVEC, continuously and variably control the intake
valve timing and exhaust valve timing, is used.System optimally control the timing of the intake
valve and exhaust valve in accordance with the
engine speed and load.
Addition of heated oxygen sensor (3rd)
Detection of the HC trap catalyst malfunction.