2008 MITSUBISHI LANCER EVOLUTION X Workshop Manual

FLOOR CONSOLE ASSEMBLY
TSB Revision
INTERIOR52A-8
FLOOR CONSOLE ASSEMBLY
REMOVAL AND INSTALLATIONM1521005200368
AC608810AB
135
6
11 4

4
12
8
1
3
2
9
14
14
15
16
10
Section D – D
A
A
Note
: Clip positions
: Claw positions
Clip
Claw
14
Section A – A Section B – B Section C – C
Clip
Clip
13
10
7
B
B
D
D
7
CC

FLOOR CONSOLE ASSEMBLY
TSB Revision
INTERIOR52A-9
REASSEMBLY SERVICE POINT
.
>>A<< FLOOR CONSOLE REASSEMBLY
Floor console rear ends (shown in the dotted lines) may dam-
age when removing the floor console cover. You can neglect
this damage and floor console is reusable.
Removal steps
1.Floor console assembly
2.Heated seat switch
3.Shift knob
4.Floor console panel assembly
5.Floor console assembly
6.Floor console harness
7.Floor console cover
8.Floor console box
9.Floor console lid
>>A<<10.Floor console
11 .Floor console bracket rear
12.Floor console bracket (A)
13.Floor console bracket (B)
14.Floor console side cover
15.Floor console front bracket (LH)
16.Floor console front bracket (RH)
Removal steps (Continued)
AC611409
Floor consoleFloor console
cover
AB

TRIMS
TSB Revision
INTERIOR52A-10
TRIMS
REMOVAL AND INSTALLATIONM1521001101049
Required Special Tool:
•MB990784: Ornament Remover
AC610310
45
1 3
6
2 79
11
12
10
13
AB
8
14
22 ± 4 N·m
16 ± 3 ft-lb
Removal steps
1.Front scuff plate
2.Cowl side trim
•Rear seat cushion (Refer
to
P.52A-23).
3.Rear scuff plate
4.Front door opening trim
5.Rear door opening trim
<>6.Front pillar trim
7.Lower center pillar trim
8.Upper center p illar trim cap
•Outer seat belt (Refer toP.52A-28).
9.Upper center pillar trim
10.Rear pillar trim
•Seat side back (Refer toP.52A-23).
11 .Rear shelf trim
12.Rear end trim
13.Trunk side trim
14.Child restraint fitting
Removal steps (Continued)

TRIMS
TSB Revision
INTERIOR52A-11
CLIP POSITION
NOTE: Each number in the illustration indicates a
part number.
AC610026AB
Note
: Clip positions
: Claw positions
Section A – A Section B – B Section C – C Section D – D
Section E – E Section F – F Section G – G Section H – H
Section I – I Section J – J Section K – K Section L – L Claw
Clip
Clip
Clip
Clip
Claw
Clip
Claw
Claw
Claw
Clip
Claw
Claw
A
B
B A
C
E
E
B DD
C A
B
J
J
KL
L
K
B
AB
F
F
G
G H
I
I I
H H
H
I
6, 10
6, 7, 10
99
7
7
1, 3
2
1212111, 3

TRIMS
TSB Revision
INTERIOR52A-12
REMOVAL SERVICE POINT
.
<> UPPER CENTER PILLAR TRIM CAP
REMOVAL
Remove the opening trim. Remove the upper center pillar trim
cap by inserting the special tool MB990784 between the upper
center pillar trim and body as shown in the illustration.
AC606516
A
A
MB990784
AIMB990784
Section A – A
Upper center
pillar trim cap

DOOR TRIM
TSB Revision
INTERIOR52A-13
DOOR TRIM
REMOVAL AND INSTALLATIONM1521006400752
Required Special Tool:
•MB990784: Ornament Remover
AC611164
15
7
12 6
2
8
9
10 11
3
4
A
Section A – A
Note
: Clip positions

A
Clip
Front door trim
assembly
AB
Removal steps
1.Front door trim assembly
2.Front door ornament
3.Front door pocket
4.Front lower pad energy absorption
5.Front door trim upper
6.Door inside handle
7.Decoration panel
8.Front door power window switch
panel assembly
9.Remote control mirror switch
10.Front door power window switch
11 .Front power window switch panel
12.Front door trim lower
Removal steps (Continued)

DOOR TRIM
TSB Revision
INTERIOR52A-14
Required Special Tool:
•MB990784: Ornament Remover
AC611175
A
ASection A – A
Clip
Rear door trim
assembly
16
11 2
3
8
10
9 5
4
NOTE : Clip positions

AB
7
Removal steps
1.Rear door trim assembly
2.Rear upper pad energy absorption
3.Rear door ornament
4.Rear door pocket
5.Rear lower pad energy absorption
6.Rear door trim upper
7.Door inside handle
8.Rear door powe r window switch
panel assembly
9.Rear door powe r window switch
10.Rear power window switch panel
11 .Rear door trim lower
Removal steps (Continued)

HEADLINING
TSB Revision
INTERIOR52A-15
HEADLINING
REMOVAL AND INSTALLATIONM1521001400973
Pre-removal and Post-installation Operation
•Removal and Installation of Front Pillar Trim, Upper Cen-
ter Pillar Trim, Rear Pillar Trim (Refer to P.52A-10).
•Removal and Installation of Instrument Under Cover
(Refer to
P.52A-6).
AC609656
2
6
1
1
1
1
3 4
45
5
7
7
8
8
9 8
9 10
10
8
AB
A
A
Section A – AClip
Claw
8
3


Note
(1) : Clip positions
(2) : Claw positions