2008 MITSUBISHI GRANDIS display

Instruments and controls
3-27
3
●Automatic reset mode
When 4 hours have passed after the ignition switch is
turned to the “OFF” or “ACC” position, the display is
automatically reset. It then shows “---”.
●Manual reset mode
If you reset the display at the time when you want to start
the measurements, average speed from that point of time
can be displayed.
To reset the display, push the “DISP” button for about
5 seconds or more.NOTE●While the ignition switch is in the “ON” position, the
automatic reset mode is permanently selected. If you wish
to make continuous measurements, select the manual
mode.
Display brightness adjustment
E00509600018
1. Press and hold down button (A), then press the “H” button
(B) within 1 second. A buzzer will sound, and the system
will allow adjustment of the display brightness.
BK-XP08E1ENUK.en-uk.book Page 27 Monday, August 13, 2007 2:20 PM

3-28 Instruments and controls
3
2. Adjust the brightness by pressing the “H” button (B) or
“M” button (C).3. Press the “SET” button (D) to determine the setting. The
display will return to the original display item.
NOTE●To cancel the brightness adjusting procedure before com-
pletion, press the button (A).
●If the “SET” button (D) is not pressed for about 15 sec-
onds or longer in the middle of the adjustment, the cur-
rently selected brightness is set automatically. Then, the
display returns to the original display item.
H- Decrease brightness
M- Increase brightness
BK-XP08E1ENUK.en-uk.book Page 28 Monday, August 13, 2007 2:20 PM

Instruments and controls
3-29
3
Display unit selection
E00509700051
It is possible to change the units in which distance, fuel con-
sumption, and time are displayed.NOTE●Except for vehicles with MITSUBISHI MOTORS genu-
ine audio, only the unit of momentary fuel consumption
can be changed to km or miles.
1. Press and hold down button (A), then press the “M” but-
ton (B) within 1 second. A buzzer will sound, and the sys-
tem will allow units to be changed.2. Use the “H” button (C) or “M” button (B) to select the
desired speed unit, then press the “SET” button (D) to
enter the setting.
H - km
M - mile
BK-XP08E1ENUK.en-uk.book Page 29 Monday, August 13, 2007 2:20 PM

3-30 Instruments and controls
3
3. If the km unit was selected in step 2, the fuel consumption
unit must be subsequently selected using the “H” button
(C) or “M” button (B).
Use the “H” button (C) or “M” button (B) to select the
desired fuel consumption unit, then press the “SET” but-
ton (D) to enter the setting.4. When you have finished setting the fuel consumption unit
(or if you selected miles in step 2), the system will require
you to proceed to select, using the “H” button (C) or “M”
button (B), whether times should be displayed in the
12-hour format or in the 24-hour format. The currently
selected format will be displayed.H - L/100km
M - km/LBK-XP08E1ENUK.en-uk.book Page 30 Monday, August 13, 2007 2:20 PM

Instruments and controls
3-31
3
Use the “H” button (C) or “M” button (B) to choose your
desired time display format, and then press the “SET” but-
ton (D) to enter the setting.5. The display will return to the original display item.
NOTE●If you selected the mile unit in step 2, the speed and fuel
consumption units will be as follows.
• Speed: mph (miles per hour)
• Fuel consumption: mpg (miles per gallon)
●To cancel the unit setting procedure before completion,
press the button (A).
●The outside temperature and digital clock are not shown
during the unit selecting procedure.
●If the “SET” button is not pressed for about 15 seconds or
longer in the middle of the selection, the currently
selected unit is set automatically. Then, the display returns
to the original display item.
H - 12-hour format
M - 24-hour format
BK-XP08E1ENUK.en-uk.book Page 31 Monday, August 13, 2007 2:20 PM

3-38 Instruments and controls
3
NOTE●If the lamp flashes unusually quickly, the bulb in a turn-
signal lamp may have burned out. We recommend you to
have the vehicle inspected.
●It is possible to activate the following functions. For fur-
ther information, we recommend you to consult a MIT-
SUBISHI MOTORS Authorized Service Point.
On a vehicle equipped with a Multi Display Station
(MDS), the functions can be adjusted on the screen. For
details, refer to a separate operation manual.
• Sounding of a buzzer as the turn-signal lamps flash
• Flashing of the turn-signal lamps and the indication
lamp in the meter when the lever is operated with the
ignition switch in the “ACC” position
Hazard warning flasher switch
E00506600567
Use the hazard warning flasher switch when the vehicle has to
be parked on the road for any emergency.
The hazard warning flashers can always be operated, regard-
less of the position of the ignition key.
Push the switch to turn on the hazard warning flashers; push
the switch again to turn them off.
When this switch is operated, all turn-signal lamps flash con-
tinuously, as do the turn-signal indication lamps in the instru-
ment cluster.
BK-XP08E1ENUK.en-uk.book Page 38 Monday, August 13, 2007 2:20 PM

Instruments and controls
3-39
3
NOTE●If the lamps are kept flashing for a long time, the battery
will be discharged, resulting in hard engine starting or no
start condition.
●It is possible to cause a buzzer to sound in time with flash-
ing of the turn-signal lamps. For further information, we
recommend you to consult a MITSUBISHI MOTORS
Authorized Service Point.
On a vehicle equipped with a Multi Display Station
(MDS), the functions can be adjusted on the screen. For
details, refer to a separate operation manual.
Fog lamp switch
E00506700018
Front fog lamp switch
E00508300050
The front fog lamps can be operated when the headlamps or
tail lamps are turned on. Push the switch to turn on the front
fog lamps, push the switch again to turn them off.
The indicator lamp in the instrument cluster will illuminate
while the front fog lamps are on.NOTE●The front fog lamps are automatically turned off when the
headlamps and tail lamps turn off. To turn on the front fog
lamps again, push the switch again when the headlamps or
tail lamps are turned on.
BK-XP08E1ENUK.en-uk.book Page 39 Monday, August 13, 2007 2:20 PM

Instruments and controls
3-41
3 Wiper and washer switch
E00507101162
The windscreen wiper and washer can be operated with the
ignition switch in the “ON” or “ACC” position.
Move the switch to operate the windscreen wipers or spray the
washer fluid.Windscreen wipers
NOTE●The speed-sensitive-operation function of the windscreen
wipers can be deactivated.
For further information, we recommend you to consult a
MITSUBISHI MOTORS Authorized Service Point.
On a vehicle equipped with a Multi Display Station
(MDS), the functions can be adjusted on the screen. For
details, refer to a separate operation manual.To adjust intermittent intervalsWith the lever in the “INT” (speed sensitive intermittent opera-
tion) position, the intermittent intervals can be adjusted by
turning the knob (A).
MIST- Misting function
The wipers will operate once.
OFF- Off
INT- Speed sensitive intermittent operation
The intermittent intervals will change with the speed of
the vehicle.
LO- Slow
HI- Fast
1- Fast
2- Slow
BK-XP08E1ENUK.en-uk.book Page 41 Monday, August 13, 2007 2:20 PM