2008 INFINITI FX35 u1000

AT-1
TRANSMISSION/TRANSAXLE
DE
F
G H
I
J
K L
M
SECTION AT
A
B
AT
N
O P
CONTENTS
AUTOMATIC TRANSMISSION
SERVICE INFORMATION .. ..........................5
INDEX FOR DTC ............................................ .....5
Alphabetical Index ............................................... ......5
DTC No. Index ..........................................................5
PRECAUTIONS ...................................................7
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
7
Precaution for On Board Diagnosis (OBD) System
of A/T and Engine .....................................................
7
Precaution .................................................................7
Service Notice or Precaution .....................................8
PREPARATION ...................................................9
Special Service Tool ........................................... ......9
Commercial Service Tool ..........................................9
A/T FLUID ...........................................................11
Changing A/T Fluid ............................................. ....11
Checking A/T Fluid ..................................................11
A/T Fluid Cooler Cleaning .......................................13
A/T CONTROL SYSTEM ....................................16
Cross-Sectional View (2WD Models) .................. ....16
Cross-Sectional View (VQ35DE Models for AWD) ....17
Cross-Sectional View (VK45DE Models for AWD) ....18
Shift Mechanism .................................................. ....18
TCM Function ..........................................................29
CAN Communication ...............................................30
Input/Output Signal of TCM .....................................31
Line Pressure Control .............................................31
Shift Control ............................................................33
Lock-up Control .......................................................34
Engine Brake Control ..............................................35
Control Valve ...........................................................36
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......38
Introduction ......................................................... ....38
OBD-II Function for A/T System ..............................38
One or Two Trip Detection Logic of OBD-II ............38
OBD-II Diagnostic Trouble Code (DTC) .............. ....38
Malfunction Indicator Lamp (MIL) ............................40
TROUBLE DIAGNOSIS ....................................41
DTC Inspection Priority Chart ..................................41
Fail-Safe ..................................................................41
How to Perform Trouble Diagnosis for Quick and
Accurate Repair .......................................................
42
A/T Electrical Parts Location ...................................48
Circuit Diagram ........................................................49
Inspections Before Trouble Diagnosis .....................49
Road Test ................................................................53
Vehicle Speed at Which Gear Shifting Occurs ........58
Vehicle Speed at Which Lock-up Occurs/Releas-
es .............................................................................
58
Symptom Chart ........................................................59
TCM Input/Output Signal Reference Value .............83
CONSULT-III Function (TRANSMISSION) ..............84
Diagnosis Procedure without CONSULT-III ............91
DTC U1000 CAN COMMUNICATION LINE .....94
Description ........................................................... ....94
On Board Diagnosis Logic .......................................94
Possible Cause ........................................................94
DTC Confirmation Procedure ..................................94
Wiring Diagram - AT - CAN .....................................95
Diagnosis Procedure ...............................................96
DTC P0615 START SIGNAL CIRCUIT .............97
Description ...............................................................97
CONSULT-III Reference Value in Data Monitor
Mode ........................................................................
97
On Board Diagnosis Logic .......................................97
Possible Cause ........................................................97
DTC Confirmation Procedure ..................................97
Wiring Diagram - AT - STSIG ..................................98
Diagnosis Procedure ...............................................99
DTC P0700 TCM .............................................101
Description .............................................................101
On Board Diagnosis Logic .....................................101
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

INDEX FOR DTCAT-5
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
SERVICE INFORMATION
INDEX FOR DTC
Alphabetical IndexINFOID:0000000001327120
NOTE:
If “DTC U1000” is displayed with other DTCs, fi rst perform the trouble diagnosis for “DTC U1000 CAN
COMMUNICATION”. Refer to AT- 9 4
.
*1: These numbers are prescribed by SAE J2012.
*2: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL.
DTC No. IndexINFOID:0000000001327121
NOTE:
If “DTC U1000” is displayed with other DTCs, fi rst perform the trouble diagnosis for “DTC U1000 CAN
COMMUNICATION”. Refer to AT- 9 4
.
Items
(CONSULT-III screen terms) DTC
Reference page
OBD-II Except OBD-II
CONSULT-III GST
(*1) CONSULT-III only “TRANS- MISSION”
A/T 1ST E/BRAKING — P1731 AT- 1 4 1
ATF 1ST GR FNCTN P0731 P0731 AT- 11 4
ATF 2ND GR FNCTN P0732 P0732AT- 11 6
ATF 3RD GR FNCTN P0733 P0733AT- 11 8
ATF 4TH GR FNCTN P0734 P0734AT- 1 2 0
ATF 5TH GR FNCTN P0735 P0735AT- 1 2 2
A/T INTERLOCK P1730 P1730AT- 1 3 9
A/T TCC S/V FNCTN
P0744(*2)P0744AT- 1 2 6
ATF TEMP SEN/CIRC P0710 P1710 AT- 1 3 2
CAN COMM CIRCUIT U1000 U1000 AT- 9 4
D/C SOLENOID/CIRC P1762 P1762AT- 1 4 7
ENGINE SPEED SIG P0725 P0725 AT- 11 2
FR/B SOLENOID/CIRC P1757 P1757AT- 1 4 5
HLR/C SOL/CIRC P1767 P1767AT- 1 4 9
I/C SOLENOID/CIRC P1752 P1752AT- 1 4 3
L/PRESS SOL/CIRC P0745 P0745AT- 1 2 8
LC/B SOLENOID/CIRC P1772 P1772AT- 1 5 1
LC/B SOLENOID FNCT
P1774(*2)P1774AT- 1 5 3
MANU MODE SW/CIRC — P1815 AT- 1 5 5
PNP SW/CIRC P0705 P0705AT- 1 0 2
STARTER RELAY/CIRC — P0615 AT- 9 7
TCC SOLENOID/CIRC P0740 P0740AT- 1 2 4
TCM P0700 P0700AT- 1 0 1
TP SEN/CIRC A/T P1705 P1705AT- 1 3 0
TURBINE REV S/CIRC P0717 P0717AT- 1 0 6
VEH SPD SE/CIR-MTR — P1721AT- 1 3 7
VEH SPD SEN/CIR AT P0720 P0720AT- 1 0 8
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-6
< SERVICE INFORMATION >
INDEX FOR DTC
*1: These numbers are prescribed by SAE J2012.
*2: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL.DTC
Items
(CONSULT-III screen terms) Reference page
OBD-II Except OBD-II
CONSULT-III GST
(*1)
C O N S U LT- I I I
only “TRANSMIS- SION”
— P0615 STARTER RELAY/CIRC AT- 9 7
P0700 P0700 TCM AT- 1 0 1
P0705 P0705 PNP SW/CIRCAT- 1 0 2
P0710 P1710 ATF TEMP SEN/CIRCAT- 1 3 2
P0717 P0717 TURBINE REV S/CIRCAT- 1 0 6
P0720 P0720 VEH SPD SEN/CIR ATAT- 1 0 8
P0725 P0725 ENGINE SPEED SIG AT- 11 2
P0731 P0731 A/T 1ST GR FNCTNAT- 11 4
P0732 P0732 A/T 2ND GR FNCTNAT- 11 6
P0733 P0733 A/T 3RD GR FNCTNAT- 11 8
P0734 P0734 A/T 4TH GR FNCTNAT- 1 2 0
P0735 P0735 A/T 5TH GR FNCTNAT- 1 2 2
P0740 P0740 TCC SOLENOID/CIRCAT- 1 2 4
P0744(*2)P0744 A/T TCC S/V FNCTNAT- 1 2 6
P0745 P0745 L/PRESS SOL/CIRC AT- 1 2 8
P1705 P1705 TP SEN/CIRC A/TAT- 1 3 0
— P1721 VEH SPD SE/CIR-MTRAT- 1 3 7
P1730 P1730 A/T INTERLOCK AT- 1 3 9
— P1731 A/T 1ST E/BRAKINGAT- 1 4 1
P1752 P1752 I/C SOLENOID/CIRC AT- 1 4 3
P1757 P1757 FR/B SOLENOID/CIRCAT- 1 4 5
P1762 P1762 D/C SOLENOID/CIRCAT- 1 4 7
P1767 P1767 HLR/C SOL/CIRCAT- 1 4 9
P1772 P1772 LC/B SOLENOID/CIRCAT- 1 5 1
P1774(*2)P1774 LC/B SOLENOID FNCTAT- 1 5 3
— P1815 MANU MODE SW/CIRC AT- 1 5 5
U1000 U1000 CAN COMM CIRCUIT AT- 9 4
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISAT-41
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
TROUBLE DIAGNOSIS
DTC Inspection Priority ChartINFOID:0000000001327148
If some DTCs are displayed at the same time, per form inspections one by one based on the following priority
chart.
NOTE:
If “DTC U1000” is displayed with other DTCs, fi rst perform the trouble diagnosis for “DTC U1000 CAN
COMMUNICATION”. Refer to AT- 9 4
.
Fail-SafeINFOID:0000000001327149
The TCM has an electrical fail-safe mode. This mode make s it possible to operate even if there is an error in a
main electronic control input/output signal circuit.
In fail-safe mode, even if the selector lever is “D” or “M” mode, the transmission is fixed in 2nd, 4th or 5th
(depending on the breakdown position), so the customer should feel “slipping” or “poor acceleration”.
Even when the electronic circuits are normal, under s pecial conditions (for example, when slamming on the
brake with the wheels spinning drastically and stopping the ti re rotation), the transmission can go into fail-safe
mode. If this happens, switch OFF the ignition switch for 10 seconds, then switch it ON again to return to the
normal shift pattern. Therefore, t he customer's vehicle has returned to normal, so handle according to the
“WORK FLOW” (Refer to AT- 4 2
).
FAIL-SAFE FUNCTION
If any malfunction occurs in a sensor or solenoid, th is function controls the A/T to mark driving possible.
Vehicle Speed Sensor
Signals are input from two systems - from vehicle speed sensor A/T (revolution sensor) installed on the trans-
mission and from combination meter so normal driving is possible even if there is a malfunction in one of the
systems. And if vehicle speed sens or A/T (revolution sensor) has unus ual cases, 5th gear and manual mode
are prohibited.
Accelerator Pedal Position Sensor
If there is a malfunction in one of the systems, the accelerator opening angle is controlled by ECM according
to a pre-determined accelerator angle to make driving po ssible. And if there are malfunctions in tow systems,
the engine speed is fixed by ECM to a pre-determined engine speed to make driving possible.
Throttle Position Sensor
If there is a malfunction in one of the systems, the accelerator opening angle is controlled by ECM according
to a pre-determined accelerator angle to make driving po ssible. And if there are malfunctions in tow systems,
the accelerator opening angle is controlled by the idle signal sent from the ECM which is based on input indi-
cating either idle condition or off-idle condition (pre- determined accelerator opening) in order to make driving
possible.
PNP Switch
In the unlikely event that a malfunction signal enters t he TCM, the position indicator is switched OFF, the
starter relay is switched OFF (starter starting is di sabled), the back-up lamp relay switched OFF (back-up lamp
is OFF) and the position is fixed to the “D” position to make driving possible.
Starter Relay
The starter relay is switched OFF. (Starter starting is disabled.)
A/T Interlock
 If there is an A/T interlock judgment malfunction, t he A/T is fixed in 2nd gear to make driving possible.
NOTE:
When the vehicle is driven fixed in 2nd gear, a turbine revolution sensor malfunction is displayed,
but this is not a turbine r evolution sensor malfunction.
 When the coupling pattern below is detected, the fail- safe action corresponding to the pattern is performed.
A/T 1st Engine Braking
Priority Detected items (DTC)
1 U1000 CAN communication line
2 Except above
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-46
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
4❏
Perform all road tests and enter checks in required inspection items. AT- 4 9
4-1.Check before engine is started
AT- 5 3
❏ The A/T CHECK Indicator Lamp does come on. AT- 1 7 0.
❏ Perform self-diagnostics. Enter checks for detected items. AT- 8 4
, AT- 9 1.
❏ DTC U1000 CAN COMMUNICATION LINE AT- 9 4
.
❏ DTC P0615 START SIGNAL CIRCUIT AT- 9 7
.
❏ DTC P0700 TCM AT- 1 0 1
❏ DTC P0705 PARK/NEUTRAL POSITION SWITCH AT- 1 0 2.
❏ DTC P0717 TURBINE REVOLUTION SENSOR AT- 1 0 6
.
❏ DTC P0720 VEHICLE SPEED SENSO R A/T (REVOLUTION SENSOR) AT- 1 0 8
.
❏ DTC P0725 ENGINE SPEED SIGNAL AT- 11 2
.
❏ DTC P0731 A/T 1ST GEAR FUNCTION AT- 11 4
.
❏ DTC P0732 A/T 2ND GEAR FUNCTION AT- 11 6
.
❏ DTC P0733 A/T 3RD GEAR FUNCTION AT- 11 8
.
❏ DTC P0734 A/T 4TH GEAR FUNCTION AT- 1 2 0
.
❏ DTC P0735 A/T 5TH GEAR FUNCTION AT- 1 2 2
.
❏ DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE AT- 1 2 4
.
❏ DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) AT- 1 2 6
.
❏ DTC P0745 LINE PRESSURE SOLONOID VALVE AT- 1 2 8
.
❏ DTC P1705 THROTTLE POSITION SENSOR AT- 1 3 0
.
❏ DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT AT- 1 3 2
.
❏ DTC P1721 VEHICLE SPEED SENSOR MTR AT- 1 3 7
.
❏ DTC P1730 A/T INTERLOCK AT- 1 3 9
.
❏ DTC P1731 A/T 1ST ENGINE BRAKING AT- 1 4 1
.
❏ DTC P1752 INPUT CLUTCH SOLENOID VALVE AT- 1 4 3
.
❏ DTC P1757 FRONT BRAKE SOLENOID VALVE AT- 1 4 5
.
❏ DTC P1762 DIRECT CLUTCH SOLENOID VALVE AT- 1 4 7
.
❏ DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE AT- 1 4 9
.
❏ DTC P1772 LOW COAST BRAKE SOLENOID VALVE AT- 1 5 1
.
❏ DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION AT- 1 5 3
.
❏ DTC P1815 MANUAL MODE SWITCH AT- 1 5 5
.
4-2. Check at Idle
AT- 5 3
❏ AT- 1 7 0 , "Engine Cannot Be Started in "P" or "N" Position".
❏ AT- 1 7 1 , "
In "P" Position, Vehicle Moves When Pushed"
❏ AT- 1 7 2 , "In "N" Position, Vehicle Moves".
❏ AT- 1 7 3 , "
Large Shock ("N" to "D" Position)".
❏ AT- 1 7 5 , "
Vehicle Does Not Creep Backward in "R" Position".
❏ AT- 1 7 8 , "
Vehicle Does Not Creep Forward in "D" Position".
4-3. Cruise Test
AT- 5 3
Part 1
❏ AT- 1 8 0 , "
Vehicle Cannot Be Started from D1".
❏ AT- 1 8 2 , "
A/T Does Not Shift: D1→ D2".
❏ AT- 1 8 4 , "
A/T Does Not Shift: D2→ D3".
❏ AT- 1 8 6 , "
A/T Does Not Shift: D3→ D4".
❏ AT- 1 8 8 , "
A/T Does Not Shift: D4→ D5".
❏ AT- 1 9 0 , "
A/T Does Not Lock-up"
❏ AT- 1 9 2 , "A/T Does Not Hold Lock-up Condition".
❏ AT- 1 9 4 , "
Lock-up Is Not Released".
❏ AT- 1 9 4 , "
Engine Speed Does Not Return to Idle".
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISAT-47
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
44-3. Part 2
AT- 5 3
❏ AT- 1 8 0 , "Vehicle Cannot Be Started from D1".
❏ AT- 1 8 2 , "
A/T Does Not Shift: D1→ D2".
❏ AT- 1 8 4 , "
A/T Does Not Shift: D2→ D3".
❏ AT- 1 8 6 , "
A/T Does Not Shift: D3→ D4".
Part 3 AT- 5 3
❏ AT- 1 9 5 , "Cannot Be Changed to Manual Mode".
❏ AT- 1 9 6 , "
A/T Does Not Shift: 5th Gear → 4th Gear".
❏ AT- 1 9 7 , "
A/T Does Not Shift: 4th Gear → 3rd Gear".
❏ AT- 1 9 9 , "
A/T Does Not Shift: 3rd Gear → 2nd Gear".
❏ AT- 2 0 1 , "
A/T Does Not Shift: 2nd Gear → 1st Gear".
❏ AT- 2 0 2 , "
Vehicle Does Not Decelerate by Engine Brake".
❏ Perform self-diagnostics. Enter checks for detected items. AT- 8 4
, AT- 9 1.
❏ DTC U1000 CAN CO MMUNICATION LINE AT- 9 4
.
❏ DTC P0615 START SIGNAL CIRCUIT AT- 9 7
.
❏ DTC P0700 TCM AT- 1 0 1
❏ DTC P0705 PARK/NEUTRAL POSITION SWITCH AT- 1 0 2.
❏ DTC P0717 TURBINE REVOLUTION SENSOR AT- 1 0 6
.
❏ DTC P0720 VEHICLE SPEED SENS OR A/T (REVOLUTION SENSOR) AT- 1 0 8
.
❏ DTC P0725 ENGINE SPEED SIGNAL AT- 11 2
.
❏ DTC P0731 A/T 1ST GEAR FUNCTION AT- 11 4
.
❏ DTC P0732 A/T 2ND GEAR FUNCTION AT- 11 6
.
❏ DTC P0733 A/T 3RD GEAR FUNCTION AT- 11 8
.
❏ DTC P0734 A/T 4TH GEAR FUNCTION AT- 1 2 0
.
❏ DTC P0735 A/T 5TH GEAR FUNCTION AT- 1 2 2
.
❏ DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE AT- 1 2 4
.
❏ DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) AT-126
.
❏ DTC P0745 LINE PRESSURE SOLONOID VALVE AT- 1 2 8
.
❏ DTC P1705 THROTTLE POSITION SENSOR AT- 1 3 0
.
❏ DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT AT- 1 3 2
.
❏ DTC P1721 VEHICLE SPEED SENSOR MTR AT- 1 3 7
.
❏ DTC P1730 A/T INTERLOCK AT- 1 3 9
.
❏ DTC P1731 A/T 1ST ENGINE BRAKING AT- 1 4 1
.
❏ DTC P1752 INPUT CLUTCH SOLENOID VALVE AT- 1 4 3
.
❏ DTC P1757 FRONT BRAKE SOLENOID VALVE AT- 1 4 5
.
❏ DTC P1762 DIRECT CLUTCH SOLENOID VALVE AT- 1 4 7
.
❏ DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE AT- 1 4 9
.
❏ DTC P1772 LOW COAST BRAKE SOLENOID VALVE AT- 1 5 1
.
❏ DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION AT- 1 5 3
.
❏ DTC P1815 MANUAL MODE SWITCH AT-155
.
5 ❏ Inspect each system for items found to be NG in the self-diagnostics and repair or replace the malfunctioning parts.
6 ❏ Perform all road tests and enter the checks again for the required items. AT- 4 9
7❏
For any remaining NG items, perform the “diagnostics procedure” and repair or replace the malfunctioning
parts. See the chart for diagnostics by symptoms. (This chart also contains other symptoms and inspection pro-
cedures.) AT- 5 9
8
❏ Erase the results of the self-diagnostics from the TCM and the ECM. AT- 8 4,
AT-
91
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-86
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
SELF-DIAGNOSTIC RESULT MODE
After performing “SELF-DIAGNOSTIC RESULT MODE”, place check marks for results on the AT-42, "How to
Perform Trouble Diagnosis for Quick and Accurate Repair". Reference pages are provided following the items.
Display Items List
X: Applicable, —: Not applicable
CLSD THL POSReleased accelerator pedal. ON
Fully depressed accelerator pedal. OFF
W/O THL POS Fully depressed accelerator pedal. ON
Released accelerator pedal. OFF
BRAKE SW Depressed brake pedal. ON.
Released brake pedal. OFF
GEAR During driving. 1,2,3,4,5, Item name Condition Display value (Approx.)
Items (CONSULT-
III screen terms) Malfunction is detected when... TCM self-di-
agnosis OBD-II
(DTC)
Reference page
“TRANS-
MISSION”
with CON- SULT-III MIL indica-
tor lamp(*1),
“ENGINE”
with CON-
SULT-III or GST
CAN COMM CIR-
CUIT When TCM is not transmitting or receiving CAN communication sig-
nal for 2 seconds or more.
U1000 U1000
AT- 9 4
STARTER RELAY/
CIRCIf this signal is ON other than in “P” or “N” position, this is judged to
be a malfunction.
(And if it is OFF in “P” or “N” position, this too is judged to be a mal-
function.)
P0615 —
AT- 9 7
TCM TCM is malfunctioning. P0700 P0700 AT- 1 0 1
PNP SW/CIRC PNP switch 1-4 signals input with impossible pattern.
 “P” position is detected from “N” position without any other posi-
tion being detected in between. P0705 P0705
AT- 1 0 2
TURBINE REV S/
CIRC TCM does not receive the proper voltage signal from the sensor.
 TCM detects an irregularity only at position of 4th gear for turbine
revolution sensor 2. P0717 P0717
AT- 1 0 6
VEH SPD SEN/CIR
AT  Signal from vehicle speed sensor A/T (Revolution sensor) not in-
put due to cut line or the like.
 Unexpected signal input during running.
 After ignition switch is turned ON, unexpected signal input from vehicle speed sensor MTR before the vehicle starts moving. P0720 P0720
AT- 1 0 8
ENGINE SPEED
SIGTCM does not receive the CAN communication signal from the
ECM.
P0725 P0725
AT- 11 2
A/T 1ST GR
FNCTNA/T cannot shift to 1st gear. P0731 P0731
AT- 11 4
A/T 2ND GR
FNCTNA/T cannot shift to 2nd gear. P0732 P0732
AT- 11 6
A/T 3RD GR
FNCTNA/T cannot shift to 3rd gear. P0733 P0733
AT- 11 8
A/T 4TH GR
FNCTNA/T cannot shift to 4th gear. P0734 P0734
AT- 1 2 0
A/T 5TH GR
FNCTNA/T cannot shift to 5th gear. P0735 P0735
AT- 1 2 2
TCC SOLENOID/
CIRCNormal voltage not applied to solenoid due to cut line, short, or the
like.
P0740 P0740
AT- 1 2 4
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-94
< SERVICE INFORMATION >
DTC U1000 CAN COMMUNICATION LINE
DTC U1000 CAN COMMUNICATION LINE
DescriptionINFOID:0000000001327165
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehi cle, and each control unit shares information and links
with other control units during operation (not independent ). In CAN communication, control units are con-
nected with 2 communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission
with less wiring. Each control unit transmits/recei ves data but selectively reads required data only.
On Board Diagnosis LogicINFOID:0000000001327166
Diagnostic trouble code “U1000 CAN COMM CIRCUIT” with CONSULT-III or 17th judgement flicker without
CONSULT-III is detected when TCM cannot communicate to other control units.
Possible CauseINFOID:0000000001327167
Harness or connectors
(CAN communication line is open or shorted.)
DTC Confirmation ProcedureINFOID:0000000001327168
NOTE:
If “DTC Confirmation Procedure” has been previously performed, alw ays turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following proc edure to confirm the malfunction is eliminated.
WITH CONSULT-III
1. Turn ignition switch ON.
2. Select “ECU INPUT SIGNALS” or “MAIN SIGNAL S” in “DATA MONITOR” mode for “TRANSMISSION”
with CONSULT-III.
3. Start engine and wait for at least 6 seconds.
4. If DTC is detected, go to AT-96, "
Diagnosis Procedure".
WITH GST
Follow the procedure “WITH CONSULT-III”.
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C