2008 GREAT WALL FLORID maintenance

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual66
6. Remove the set bolts and the select lever assembly.
7. Remove the select lever subassembly.
8. Remove the shaft retainer on the shift shaft and the se-
lect lever.
Caution: Use a cord to fasten the shift lever in order to
make the operation convenient.Cord
9. Remove the shift shaft and the shift shaft dust cover.

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual68
Disassembling the Differential Subassembly
Components
T oil sealClutch housing
Tapered roller bearings
Elastic cylindrical pin
Odometer drive gear
Differential case
Differential ring gear
Bolt for flange face
Gasket
Planetary gear
Adjusting shim
Axle shaft gear
Planetary gear shaft
Planetary gear
Gasket
Axle shaft gear
Adjusting shim
Tapered roller bearings
Transmission case
Adjusting shim
T oil seal
123.6
: Specified torqueN·m

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual70
5. After removing bolts for flange face from the differential
ring gear and the differential case, gently pound to re-
move the differential ring gear with a soft hammer.
6. Remove the elastic cylindrical pins from the differential
case and the gear shaft.
7. Remove 2 planetary gears, 2 axle shaft gears, 2 ad-
justing shims, and 2 gaskets from the inside of the dif-
ferential case.

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual72
Suspension System Technical Parameters
Main technical parameters
Suspension type and
composition
Front suspension typeMcPherson independent suspension
Front suspension componentsCoil spring, hydraulic telescopic shock absorber, stabilizer bar, lower swing
arm
Rear suspension typeCompound trailing arm semi-independent suspension
Rear suspension componentsCoil spring, hydraulic cylinder damper, & twist beam welded components
Wheel positional
parameters
(no load)
Front wheel camber-0° 43′ ±30′
Front wheel kingpin angle+10° 21′ ±30′
Front wheel kingpin caster+1° 49′ ±30′
Front wheel toe-in-0° 01′ ±15′
Rear wheel camber-0° 43′ ±30′
Rear wheel toe-in+0° 14′ ±15′
Wheel and tire parameters
Tire specifications: 15 × 6J (For 185/65R15 tires), 16 × 4T (For T125/70R16 tires)
Tire specification: 185/65 R15 88H
Spare tire specification: T125/70R16 96M
Tire pressure must be gauged when the tire is cool: Tire inflation pressure: 200±10 KPa
Spare tir e inflation pressure: 420±10 KPa
Tightening torque
PartCodeAssembly locations for
standard components
Tightening
torque
(N·m)
QuantityGlueGrade
Front
suspen-
sion
Q1861455TF2
(M14×1.5) + Q402
(d2=32 t=5) FD
Subframe & vehicle body (rear)145±15 2Red glue10.9
Q1861275TF2
(M12×1.25) + Q402
(d2=32) FD
Subframe & vehicle body (front)120±102Red glue10.9
Q1401020 (M10×1.25) FDSubframe strut bar mounting bolt49±54Red glue10.9
2904011-S08Swing arm & steering knuckle98±102Red glue
Q1401495 (t=4)
(M14×1.5) FDSwing arm & subframe (front)180±102Red glue10.9
Q1401280 (M12×1.25) FDSwing arm & subframe (rear)120±102Red glue10.9
2904013-S08Swing arm & subframe (rear)/2
2905011-S08Front shock upper assembly loca-
tion40±56
Q32014 (M14×1.5) FDFront shock lower assembly loca-
tion132±104Red glue10.9
Q1400830 (d2=13.5)F r o n t s t a b i l i z e r b a r m o u n t i n g
bracket37±44Red glue
Q32608Front stabilizer bar hanger rod16±24
Rear sus-
pension
Q151B12110TF2+Q402
(d2=35 t=5) FDTwist beam & vehicle body80±102Red glue10.9 grade
with guide
Q32012T13F2
(M12×1.25) FDRear shock absorber & twist beam120±102Red glue10 grade
Q341C10Rear shock absorber & vehicle
body64±54
Wheel3101014-K00Wheel nut (M12×1.25)110±1016
Q30612FD (M12×1.25)Wheel nut cone nut110±1016

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual74
3. Remove the wheel speed sensor and the brake hose
Remove the wheel speed sensor's mounting bolts with a M10
sleeve to take off the wheel speed sensor. Remove the front
brake hose's mounting bolts with a M18 sleeve, and then
take off the brake hose.
Caution: When removing the brake hose, brake fluid
may flow out, catch the fluid with a container. Also,
b e c a u s e t h e b r a k e f l u i d i s c o r r o s i v e , p l e a s e p a y
attention to personal protection.
4. Remove the cotter pins and lock nuts of the steering tie
rod and the lower swing arm
Because the ball stud and steering knuckle act in conjunction
with the tapered bore, they can not yet be removed after re-
moving the nuts. Pound the steering knuckle arm (unfinished
surface) with a hammer. Positions are shown on the left.
Shake to loosen.
Caution:
1. To avoid separating the ball studs, do not pound the
tie rod and the lower swing arm with a hammer.
2. To avoid damaging the thread, do not hammer the
ball stud's head.
Front brake hose mounting bolt
Wheel speed sensor mounting bolts
Lightly hammer here

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual76
Front shock absorber with coil spring assem-
bly disassembly and installation
1. Compression spring
Use SST to grasp the spring, separated by adhesive tape
at the contact area. Alternately rotate the bolts on the SST
until there is no tension on the spring seat from the spring.
The front coil spring rotating means that the spring has been
compressed (shown on the left).
2. Disassemble the front shock absorber with coil spring
assembly
Remove the dust cover of the front shock absorber. Remove
the nuts on top using a ratchet wrench and M21 sleeve. Re-
move the erection support on the front shock absorber col-
umn, support bearing, the front coil spring's erection support,
front coil spring, dust cover, and the bumper in turn.
Tightening torque: 40-60 N·m
3. Retracting spring
Alternately reversing, rotate the bolts on the SST until all the
spring tension is released, then remove the tool.
4. Change any component that needs to be replaced
5. Installation of the front shock absorber with coil spring
assembly
Installation is in the reverse order of disassembly,
please pay attention to items below:
(a) Use SST to compact the spring.
(b) Steps for the installation of each component of the
front shock absorber with coil spring assembly is the
opposite of the steps for its disassembly.
(c) Pull up the strut piston rod as hard as possible and
make sure not to let it draw back into the strut.
(b) All of the fastening pieces must be tightened to the
required torque, and comply to the standard gluing re-
quirements in this chapter.

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual78
Remark: When removing the subframe's front mounting bolt,
an extension bar should be inserted through the lower swing
arm's hole. Positions shown on the left.
5. Subframe installation.
Installation follows the reverse removal steps.
Caution: Fix the position of the subframe with the
position pin, to avoid influencing the four wheels'
positioning. Location hole is shown on the left: a total
of two, one on the left and one on the right.
Stabilizer bar removal and installation
1. Remove the hanger rod.
Use a M10 open-end wrench to lock the sliding side of the
hanger rod (slightly higher than center position), screw off
the hanger rod lock nuts, and remove the hanger rod.
Caution: These are non-metal insert lock nuts, and
cannot be reused. So please replace them with new
ones after removal.
2. Remove the stabilizer bar arm.
Remove the stabilizer bar bracket mounting bolts Q1400830
(d2=13.5), and take down the bracket and bushing. As shown
on the left: There are four bolts, two on the left and two on
the right.
Tightening torque: 23±3 N·m
3. Stabilizer bar installation.
Install it by reversing the removal steps, but please pay
attention to the areas of importance below:
(a) During removal, please remember the installation order
of each of the hanger rod's components, so as to avoid
improper installation.
Insert extension bar through this hole
This is the subframe location hole
Q1400830
WasherBushingHanger rod
Shaft sleeve
BushingWasher

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual80
Lower Swing Arm
Components
Swing arm removal and installation
1. First, remove the steering knuckle, subframe, and
stabilizer bar hanger rod. For detailed steps, please
refer to the removal of the steering knuckle, subframe,
and stabilizer bar.
2. Screw off the lower swing arm's front mounting bolt
Q1401495 (t=4) (M14×1.5) FD with a sleeve.
Tightening torque: 136±10 N·m
3. Screw off the lower swing arm's rear mounting bolt
Q1401280 (M12×1.25) FD with a sleeve.
Tightening torque: 107±10 N·m
Caution: The nuts here are designed to prevent sliding.
When installing or removing, please do not tighten or
loosen this part, a sleeve needs to be used to apply
force onto the bolt.
Lower swing arm
SubframeQ1401495
Q1401280
Q1401495
Q1401280