2008 GREAT WALL FLORID maintenance

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual246
Cooling Unit
Components
Radiator removal
1. Remove the battery negative (-) terminal.
2. Remove the electronic fan connector.
3. Screw off the radiator drain valve, and drain the cool-
ant.
4. Disconnect the engine's water inlet and outlet pipes.
Caution: Avoid impurities entering the pipes.
5. Use a No. 10 wrench to separate the radiator upper
cross member from the vehicle body.
6. Take the radiator out of its mounting hole.
7. Remove the radiator inlet and outlet pipe.
Radiator filler assembly
Radiator upper mount
Radiator inlet connecting pipe
Attachment clip
Radiator assembly
Overflow pipe
Radiator inlet pipe
Electronic fan with overflow tank assembly
Mounting bolt
Radiator outlet pipe
Attachment clip
Radiator lower mount
Radiator drain valve
Fan connection port
Radiator upper cross member
Radiator lower mount
Radiator upper mount
Radiator outlet pipe
Radiator inlet pipe
Radiator
outlet pipe
Radiator inlet pipe

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual248
Front door removal
1. Remove the front door inner decoration board.
(a) Remove the interior armrest screw and armrest.
(b) R e m o v e t h e d o o r i n s i d e h a n d l e s c r e w a n d i n s i d e
handle.
(c) Remove the electrical switch and pull out the wire
harness.
(d) Insert buckle screwdriver between the fixed buckle and
the door inner decoration board to pry them loose.
Caution: Before using a buckle screwdriver, make sure
to wrap its head in tape.
(e) Take down the door inner decoration board.
Front Door Assembly
Components
Front door triangular protector LH
Front door protector assembly LH
Front door armrest LH
Front door internal weatherstrip LH
Front door assembly LH
Front door lower hinge assembly LH
Front door retainer LH
Front door upper hinge assembly LH
Left external rearview mirror assembly
Front door window front guide rail assembly LH
Front door glass run LH
Front door window LH
Front door weatherstrip LH
Front door external weatherstrip LH
Front door lock assembly LH
Window regulator assembly
Front door window rear guide rail assembly LH
Front door armrest LH
Front door window
switch assembly LH
Front door protector LH

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual250
6. Install the front door glass run.
7. Install the front door window assembly.
Install the window on door chamber and fix the window and
window regulator with two bolts.
4. Install the window regulator.
(a) Install the regulator via the auxiliary hole.
(b) Install the six mounting bolts of the regulator.
5. Install the guide rail and bolts on the front door window
guide rail assembly.
9. Install the door inner decoration board.
10. Install the front door inside handle.
(a) Push the door handle into the door panel and slide it
backward.
(b) Screw in the screws.
11. Insert the wire harness of the front door power window
switch and install the door handle.
8. Install the front door external weatherstrip.
Lower the window and make the external weatherstrip
wedge into the seam of the door's external panel.
Front door protector LH
Front door assembly LH
Window regulator assembly
Front door assembly LH
Front door window LH
Front door assembly LH
Front door external weatherstrip LH
Front door armrest LH
Front door inside handle LH

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual252
2. Remove the rear door external weatherstrip.
Lower the window and manually grasp the weatherstrip
firmly, then pull it up to remove.
3. Remove the rear door window assembly.
(a) Pull the rear door regulator down in a position that en-
ables the rocker to turn freely, and then lower the win-
dow. Finally make the rocker slide out of the guide rail
below the window.
(b) Pull the window upwards and then tilt it to remove.
4. Remove the rear door glass run.
5. Remove the rear door window guide rail assembly.
6. Remove the window regulator.
(a) Remove the four mounting bolts of the regulator
bracket.
(b) Remove the regulator via the auxiliary hole.
7. Remove the vehicle inner lock button.
8. Rear door window assembly replacement.
(a) Adjust the rear door window to make the window
b r a c k e t m o u n t i n g b o l t s l e v e l w i t h t h e d o o r i n n e r
decoration board mounting hole.
(b) Remove the window bracket mounting bolts to take the
window out for replacement.
Rear door installation
1. Coat grease.
Coat MP grease on the components before installing them.
(a) Coat MP grease to sliding surfaces and the gears of
window regulator.
Caution: Do not coat MP grease to the spring of the
window regulator.
(b) Coat MP grease to the sliding surface of the door lock.
4. Install the window regulator.
(a) Install the regulator via the auxiliary hole.
(b) Install the four regulator's mounting bolts.
2. Install the door outside handle with lock cylinder and
door lock.
(a) Install the lock cylinder on the door outside handle with
spring clasp.
(b) Install the door outside handle and lock cylinder with
two bolts.
(c) Install the door lock with three bolts.
(d) Connect the control lever to the door outside handle.
3. Install the door inner lock button and connect the con-
trol lever.
Rear door window rear guide rail LH
Rear door glass run LHRear door window LH
Rear door external weatherstrip LH
Rear door window front guide rail LH
Rear door window regulator LH
Rear door window regulator LH
Rear door assembly LH
Rear door outside handle assembly LH
Rear door window regulator LH
Rear door lock assembly LH
Rear door assembly LH
Rear door outside handle assembly LH
Rear door window regulator LH
Rear door assembly LH
Rear door outside handle assembly LH
Rear door assembly LH
Rear door lock assembly LH

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual254
Trunk Door Assembly
Components
Right side decorative blockLeft side deco-rative block
High mount brake lamp cap
Spoiler panel assembly
Trunk door assembly
High mount brake lampshade
High mount brake lamp assembly
Trunk door main lock assembly
Trunk door right side air spring
Trunk door hinge assembly
Trunk door assembly
Trunk door outside handle assembly
Trunk door plate
Trunk door handle
Trunk door protector assembly
Trunk door weatherstrip
Trunk door left side air spring
Rear wiper assembly
Trunk door glass weatherstrip
Trunk door lock button
High mount brake lamp assembly 2
Trunk door resonance block
Trunk door glass weatherstrip

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual256
Front Bumper
Components
1
2
34
5
6
7
8
9
10
11
9
8
6
53
11
11
11
11
1. Front bumper plastic support2. Front bumper energy absorbing block 3. Cross slot & concave hexagon head self-tapping screw and large washer subassembly (Q2754819+Q422) 4. Front bumper left mounting bracket 5. Cross slot & concave hexagon head self-tapping screw and large washer subassembly (Q2756319+Q421) 6. Front bumper plastic nut seat 17. Front bumper body8. Hexagon head bolt and flat washer subassembly (Q1400616)9. Front bumper plastic nut seat 210. Front bumper right mounting bracket 11. Expansion button

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual258
7. Disconnect the wire harness of the left & right fog lamps.
8. Remove the bumper attachments.
Remove the front bumper plastic support and energy absorb-
ing block from the vehicle body respectively.
9. Remove the bumper bracket.
Screw off the cross slot & concave hexagon head self-tapping
screw and large washer subassembly (Q2756319+Q422) on the
left / right side mounting bracket of the front bumper, and pull
the left / right side mounting bracket out.Front bumper body
Front bumper body
Front bumper energy absorbing block
Front bumper plastic support
Front bumper left side mounting bracket
Cross slot & concave hexagon head self-tapping screw and large washer subassembly

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual260
2. Remove the nut and gasket.
Screw off the hexagon nut for flange face from the rear bum-
per left & right side central mounting bolt, and the rubber
cushion of the rear bumper left & right side central mounting
bracket.
3. Remove the expansion button connecting the left &
right side bracket below the rear bumper and vehicle
body.
4. Remove the bumper mounting bolt.
Screw off the rear bumper mounting bolt connecting the left
& right side above the rear bumper and vehicle body.
5. Pull the bumper out.
Pull the rear bumper out of the left & right side bracket of
the rear bumper, and make the central part of the rear bum-
per slide out along the rear bumper central mounting bracket
bolt.
6. Remove the three rear bumper plastic buffer anchor
from the rear impact beam.Rear bumper body
Rear bumper body
Rear bumper body
Rear bumper body
Rear bumper
Rear bumper plastic buffer anchor
Central left mounting bracket of the rear bumperRear mounting bracket LH of the rear bumper
Front mounting bracket LH of the rear bumper
Rear bumper central mounting bracket bolt
Rear bumper mounting bolt
Expansion button
Hexagon nut for flange face
Rubber cushion of the rear bumper central mounting bracket