2008 GREAT WALL FLORID maintenance

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual230
Alignment area
(a) Whether there are broken connectors or protective
pipes and deformed terminals.
(b) Whether the housing is damaged.
(c) Inspect whether the clock spring's upper connector
terminal and lower corresponding connector terminal is
conducting.
Clock spring central involution
Screw in the clock spring clockwise all the way, and then
turn it 3.5 circles in the reverse direction, until the position
pin's block boss matches the block hole (as shown on the
left).
Caution: If the clock spring is not in the involution
central, the steering wheel will be unable to rotate
midway or cause clock spring circuit failure, which will
obstruct the normal operation of the SRS airbag.
6. Steering wheel and airbag module subassembly installation
(a) After pulling out the clock spring's position pin, install the steering wheel and airbag module su\
bassembly.
Caution: While installing the steering wheel and airbag module subassembly, please do not block the
clock spring wire harness.
(b) After installation, try to turn the steering wheel left and right to its proper position, and check for anything
abnormal.
7. Inspection after installation
(a) Lightly turn the steering wheel left and right to check whether there is anything abnormal or for any
strange noise. (Driver side airbag module, clock spring).
(b) Set the ignition switch to the ON position.
(c) The SRS warning lamp will remain on for 6-7 s and will then die out.
(d) If the warning lamp is always on or shows other symptoms after 6-7 s, troubleshooting must be perf\
ormed.
(e) Inspect whether the clock spring circuit is open circuited. If yes, please replace it with a new \
one.
(f) If no, check the other circuits.
Airbag Module Disposal
While discarding the airbag module or a vehicle carrying a SRS airbag, please discard according to the following
steps.
Discarding essentials of the airbag module before deployment
1. Deploy the airbag before discarding SRS airbag.
2. Deploy the airbag outside the vehicle when replacing the airbag module.
3. There may be some smoke when deploying the airbag, so make sure to operate near a smoke
detector.
4. When deploying the airbag, the sound will be very loud. Please ask nearby people to plug their ears,
and try not to operate near residential areas.
Airbag deployment
Wa r n i n g : T h e f o l l o w i n g s t e p s c a n p r e v e n t s t a t i c
electricity trigged accidental deployment, so please
carefully follow them.
1. Park the vehicle on a flat surface.
2. D i s c o n n e c t t h e b a t t e r y ' s n e g a t i v e a n d p o s i t i v e
terminals, and remove the battery from the car.
Caution: Avoid wearing apparel which may generate
friction due to electricity. Disconnect the battery's
p o s i t i v e a n d n e g a t i v e t e r m i n a l s , a n d c o m m e n c e
operation after waiting 60 s.
3. Remove the airbag module according to the driver side
airbag's normal removal procedures.
1
2
3

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual232
Airbag’s Diagnostic Methods Without a Diagnostic Scanner
Airbag indicator lamp warning
Check the airbag ECU connectors for looseness, check for warnings after correct installation.
Inspect whether the clock spring is conducting
Go to a professional maintenance station to perform inspection
Disconnect the front passenger side seat belt pretensioner wires and replace it with a 2 Ω resistor to see whether airbag warning lamp is still on.
Disconnect the driver side seat belt pretensioner wires and replace it with a 2 Ω resistor to see whether airbag warning lamp is still on.
Disconnect the front passenger side airbag line and replace it with a 2 Ω resistor to see whether airbag warning lamp is still on.
D i s c o n n e c t t h e d r i v e r s i d e a i r b a g l i n e a n d replace it with a 2 Ω resistor to see whether airbag warning lamp is still on.
Check whether the alarm continues after replacing the clock spring
No
No
No
No
NoNo
Yes
Yes

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual234
Front Door Lock Assembly
Components
Front door lock installation and removal
1. Install the outside handle framework.
Install the door lock tie rod on the outside handle's framework,
install the outside handle framework, and tighten
the mounting screw.
2. Install the gasket.
3. Install the outside handle of the front door on the out-
side handle framework.
Inside handle assembly
Front door lock assembly LH
Lock mounting screw
Gasket
Front door locking cable installing buckle
Front door unlock cableFront door lock cable
Front door lock latchFront door lock cylinder assembly LH
Lock cylinder decorative cap
Front door outside handle
Gasket
Front door outside handle framework
Front door tie rod assembly
Q2580820 + Q141F32
Framework mounting screw
Door lock tie rod
Front door outside handle
Gasket mounting hole

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual236
10. Install the door lock latch.
11. Front door lock removal.
For the removal, please simply reverse the installation steps.
Caution: The front door tie rod can be removed following
the outside handle framework. The front door tie rod
can be removed after the removal of the outside handle
framework.
Door lock latch
Q2580820 + Q141F32

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual238
5. Install the rear door lock assembly.
Install the assembled assembly, tighten the lock mounting
screws (pay attention to put the outwardly open swing arm
lever clip of the lock onto the outer opened fork of the out-
side handle framework), and then insert the wire harness
plug-in into the door lock socket.
6. Install the cable buckle.
7. Install the inside handle.
Clamp the inside handle clip to the door inner decoration
board, and then firmly press the inside handle clip dowel pin
into the mounting hole.
8. Install the rear door outside handle decorative cap, and
tighten the decorative cap mounting bolt.
9. Install the inside handle screw.
When the door cylinder panel assembly is installed, tighten
the inside handle's mounting screw.
10. Install the rear door lock latch.
11. For rear door lock removal, please simply reverse the
installation steps.
Door lock fork
Inside handle dowel pin
Inside handle clip
Mounting screw
Door lock inside handle
Rear door lock latch
Q2580822

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual240
Wiper arm and vent panel removal and in-
stallation
1. Remove the bolt cover of the wiper arm.
2. Remove the retaining bolt of the wiper arm.
3. Wobble the wiper arm to remove it.
Wiper Arm and Vent Panel Assembly
Components
4. Take off the rear weatherstrip of the engine hood from
the vent panel.
5. Remove the screws from the two ends of vent panel.
6. Remove the expansion button in the middle of the right
and left vent panels.
7. For wiper arm and vent panel Installation, please simply
reverse the removal steps.
Right wiper arm
Left wiper arm
Wiper arm bolt cover
Wiper arm bolt
Left vent panel
Right vent panel
Engine hood rear weatherstrip
Screw
Screw
Wiper arm bolt cover
Wiper arm bolt
Wiper arm
Engine hood rear
weatherstrip
Vent panel expansion button
Screw

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual242
Dashboard
Components
Dashboard removal
1. Remove the auxiliary facia console.
(a) Take down the front ash tray assembly
(b) Take down the auxiliary facia console decorative carpet.
(c) Remove one screw.
(d) Remove the parking brake lever panel.
(e) Remove the shift lever cap.
(f) Remove the auxiliary facia console assembly.
2. Remove the left & right trim strip assembly of the dash-
board.
Front ash tray assembly
Dashboard top assembly
Combination switch cover assembly
Dashboard lower framework assemblyGlove box assembly
Fuse box
Dashboard left trim strip
Dashboard center console left trim strip
Ash tray assembly
Coin box bottom
Coin box coverFront ash tray assembly
Dashboard center console right trim strip assembly
Small glove box assembly
Shift handle cover assembly
Auxiliary facia console
Dashboard center console assembly
Air-conditioner center right air outlet tray assembly
Combination meter hood assembly
Side air outlet decorative cap
Air-conditioner air outlet wind-ball assembly
Air-conditioner air outlet tray assembly
Air-conditioner left air outlet tray assembly
Dashboard right trim strip
Parking brake lever panel
Auxiliary facia console decorative carpet
Screw
Buckle
Auxiliary facia console
Dashboard right trim strip assembly

Downloaded from www.Manualslib.com manuals search engine 244GWFLORID Maintenance Manual
11. Remove the dashboard top assembly.
(a) Remove the four screws.
(b) Remove the dashboard top assembly.
12. Remove the air conditioner controller (refer to air con-
ditioner controller removal for details).
13. Remove the small glove box assembly.
(a) Remove the four screws.
(b) Remove the small glove box assembly.
14. Remove the ash tray assembly.
(a) Remove the two screws.
(b) Remove the ash tray assembly.
15. Remove the coin box cover.
16. Remove the coin box bottom.
(a) Remove the two buckles.
(b) Remove the coin box bottom.
17. Remove the combination switch (refer to combination
switch removal for details).
Small glove box assembly
Ash tray assembly
Coin box cover
Screw
Screw
Dashboard top assembly
Screw
Screw
Coin box
bottomBuckle
Buckle