2008 GEELY FC key

Engine cover/automobile door
Engine cover......................................................
366
Adjustment.....................................................
366
Front automobile door........................................
367
Subassembly.................................................
367
Overhaul........................................................
369
Adjustment.....................................................
372
Rear automobile door.......................................
373
Overhaul........................................................
373
Adjustment....................................................
375
Trunk cover.........................................................
377
Adjustment....................................................
377
Torsion spring of trunk cover.............................
378
Change..........................................................
378
Exterior/inner trim board
Front bumper....................................................
379
Subassembly................................................
379
Change..........................................................
380
Rear bumper......................................................
381
Subassembly................................................
381
Change..........................................................
382
Name plate........................................................
383
Change..........................................................
383
Exterior seal tape of left front door glass (LH)...
384
Change..........................................................
384
Exterior seal tape of left rear door glass...........
385
Change..........................................................
385
Light fender........................................................
386
Change..........................................................
386
Top left trim tape.................................................
387
Replacement.................................................
387
Left lower fender of automobile body (LH)........
388
Subassembly................................................
388
Change..........................................................
389
Inner trim board of top........................................
390
Change..........................................................
390Automobile control system
Ignition switch and anti-versa lock key warning switch.394
Malfunction phenomenon table.....................
394
Inspection......................................................
394
Electrical schematic diagram..............................
395

Engine mechanism - Timing chain assembly(2) Use damping pulley bolts to turn crankshaft with its key
toward upward.
(b) Install timing chain on crankshaft timing sprocket and
align the chain link having yellow mark with timing mark
of crankshaft timing sprocket.
Hint: there are 3 yellow chain links on the timing chain.(c) Install crankshaft timing sprocket with special tool.
(d) Install timing chain on camshaft timing sprocket and
align the chain link having yellow mark with camshaft
timing sprocket.27. Install chain guide rail components.Torque: m28. Install chain tension rail components.Torque: 29. Install speed sensor signal panel.Install signal panel with “F” mark toward forward.Toward portSet key
Yellow
mark
Timing mark
Special tool
Color (yellow) mark
Timing mark 47

Engine mechanism - Timing chain assembly(b) Coat engine oil on the chain tensioner, and then install
it.
Torque: Note: when installing the chain temsioner, buckle
on the hook again if plunger has ejected.33. Install damping pulley.(a) Align the key groove on the damping pulley with the
key on the crankshaft, and slide damping pulley in.
(b) Install damping pulley bolts with special tool.
Torque: (c) Turn crankshaft counterclockwise to separate the hook
from lock pin on the plunger.
(d) Turn crankshaft clockwise, and check the chain ten-
sion rail is blocked by plunger.
Hint: if the plunger does not eject, press the chain ten-
sion rail toward chain tensioner with screwdriver
or fingers to separate the hook from lock pin and
make the plunger eject.Special
tool 49 Pushing intoSeparationHook
Pin
TurningPlunger
Pushing
intoTurning

Engine mechanism - CamshaftWarning: if the air pressure in timing advance side oil duct is released earlier than that in
timing delay side oil duct, VVT driver assembly will move suddenly toward
delay side.This will cause the damage of lock pin.
(g) Remove VVT drive fixed bolts.
Notes:
It is strictly forbidden to remove other 4 bolts.
Under the condition of repeating using camshaft
timing sprocket, release lock pin at first, and then
install sprocket.12. Install VVT driver assembly.
13. Install camshaft.Put VVT driver assembly together with intake camshaft.
(a) As shown in the diagram, gently make VVT assembly
hold camshaft and turn it toward left until straight pin is
inserted into groove.
Warning: it is strictly forbidden to turn camshaft
timing sprocket toward timing delay side
(toward right).
(b) Check there is no clearance between sprocket flange
and camshaft.
(c) Fix camshaft timing sprocket and then tighten flange
bolt.
Torque: 70 ±5N.m
(d) Check VVT driver assembly could move to timing
delay side and is locked at max. timing delay position.
(f) As shown in the diagram, align alignment mark with
timing mark on camshaft timing sprocket, and install
timing chain on the timing sprocket.
(g) Check forward mark and figure, and tighten bolts as
sequences shown in the diagram.
Torque: 13 ±0.78N.m
(h) Align alignment mark on the chain with timing mark on
camshaft timing sprocket, and place exhaust camshaft
in cylinder head.Straight pin
key
grooveFlange bolt
Straight pin56Timing remark
chain linkTiming mark
Timing remark chain link
Timing mark

Engine mechanism - Crankshaft front oil seal assembly5. Remove crankshaft front oil seal.(a) Cut oil seal lip with blade.
(b) Prize out oil seal with flat screwdriver whose sharp end is
winded with tape.
Note:check crankshaft is damaged after removing oil
seal, and repair with abrasive paper (#400) if it
is damaged.6. Install crankshaft front oil seal.(a) Coat a little MP grease on new oil seal lip.
Note: do not let oil seal lip contact with foreign
matters.
(b) Gently knock new oil seal in with special tool and hammer
until the seal surface is parallel and level with the end sur-
face edge of mounting hole.
Note: wipe off redundant grease on crankshaft.7. Install damping pulley.(a) Align the key groove on the pulley with the key on the
crankshaft, and slide pulley in.
(b) Install pulley bolts with special tool.
Torque: m8. Install right engine mounting assembly.Torque: 9. Check there is oil leakage.Cut
position
Prizing out
Special
tool61Special
tool

Lubrication - Oil pump assemblyOil pump assemblyReplacement1. Remove timing chain assembly (see Page 45).
2. Remove oil pump assembly [4G18-1011100].Remove 5 bolts, oil pump and oil pump gasket.3. Install oil pump assembly.(a) Install new gasket on cylinder body.
(b) Align the guide groove of oil pump drive rotor with the key
on crankshaft, and slide the oil pump in.
(c) Install oil pump with 5 bolts.
Torque: 76

Steering column--Steering systemSteering column--Steering system
Steering column--Steering systemSteering column--Steering systemSteering column--Steering system
13. Disassemble ignition switch key tank assembly
(a) Put ignition switch key tank on ACC position.
(b) Pull down stop pin and pull out key tank assembly with
right-angled screwdriver.
14. Disassemble ignition switch assembly
Disassemble two screws, and take down ignition switch
assembly.
15. Assemble ignition switch with locking core and key
assembly [68000019]
Assemble ignition switch with locking core and key assembly
with two screws.
16. Assemble ignition switch key tank assembly
(a) Make sure ignition switch key tank assembly locates at
ACC position.
(b) Assemble ignition switch key tank.
17. Steering locking function
(a) When taking out the key, check whether steering locking
organization is locked.
(b) When inserting the key, and turning to ACC, check whether
the steering locking organization is released.
18. Assemble electronic anti-stealing loop assembly
[67000009]
19. Assemble ignition switch clamp [68000020]
20. Assemble steering shaft assembly
(a) Assemble steering column assembly with three bolts.
Torque: 21 ± 2 Nxm
 196 

Air conditioner--Condenser Assembly(b) Disassemble two bolts.
(c) Pull the component on the top of water tank assembly back
to disassemble the condenser assembly.6. Disassemble the drier(a) Use 10mm hexagon wrench to disassemble the cover and
filter core from regulator.
(b) Disassemble two O-shape rings from the cover.
(c) Use the acutilingual pliers to disassemble the drier.7. Assemble the drier.(a) Use the acutilingual pliers to assemble the drier.
(b) Put the O-shape ring in the cover.
(c) Spread freezing lubricant at the connecting part between
the O-shape ring and the cover.
Refrigerant oil: 100PG
(d)Use the 10mm hexagon wrench key to assemble the cover
to condenser assembly.
Torque: 12.3 N⋅ ⋅⋅ ⋅
⋅m8. Assemble condenser assembly.
9. Assemble Refrigerant NO.1 high pressure hose.(a) Disassemble the cover from the tie –in of the pipe.
(b) Daub enough Refrigerant oil to lubricate at the connecting
part between the O-shape ring and the cover.
Refrigerant oil: 100PG
(c) Use the bolt to connect Refrigerant high pressure hose
with condenser assembly.
Torque: 5.1 N⋅ ⋅⋅ ⋅
⋅mInner hexagon
socket wrench
Adjuster 237