2008 GEELY FC brake sensor

Brake--Speed sensor of rear wheelsSpeed sensor of rear wheelsChangeHint: the process for changing right side is same as the
left side.1. Disassemble rear wheels.
2. Disassemble wiring harness of speed sensor of rear
wheel.Disassemble the joint of speed sensor of rear wheel.3. Disassemble left rear disk brake branch pump
assembly.
4. Disassemble rear brake disk.
5. Disassemble left rear shaft hub and bearing assem-
bly (referring to page 129).
6. Disassemble speed sensor of rear wheel.(a) Fix rear shaft hub on pliers with soft gasket.
Note: when changing shaft hub assembly, it is neces-
sary to shake intensively to make it break off.
(b) Use punch pin and hammer to knock out two pins.
(c) Use special tool and two bolts (M12*1.5) to disassemble
speed sensor of rear wheel from rear shaft hub.
Note:zIf sensor stator is damaged, change the shaft hub
assembly.zDo not scratch the surface of shaft hub and speed
sensor.7. Assemble speed sensor of rear wheels.(a) Wash contacting surface of rear shaft hub and new speed
sensor of rear wheels.
(b) When sensor is assembled in shaft hub, it is necessary
to assemble sensor joint facing lower position of
automobile.Special
tool
Special tool Bolt
Bolt152

Brake--Speed sensor of rear wheels153(c) Use special tool and press to assemble speed sensor of
rear wheels to rear shaft hub.
Note:zDo not use hammer knock directly in speed sensor
of rear wheels.zInsure no sundries are attached on the supervising
part of speed sensor of rear wheelszPress speed sensor of rear wheels straightly and
slowly.8. Assemble left rear shaft hub and bearing assembly
(referring to page 129).
9. Assemble brake disk.
10. Assemble left rear brake branch pump.
11. Assemble wiring harness of speed sensor of rear
wheels.
12. Assemble rear wheels.Torque: 103
± ±± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m13. Check and adjust wheel alignment.
14. Check the signal of ABS speed sensor.Special
tool

Parking front brake pull cable assembly
Change
Parking brake--Parking front bake pull cable assembly
 156  1. Disassemble upper trim board on box.
2. Disassemble parking brake hole cover.
3. Disassemble central box.
4. Disassemble parking brake handle assembly.
5. Disassemble front bottom board bracket.
6. Disassemble front exhaust pipe with Three-Way
Catalytic Converter assembly.
(a) Disassemble the joint of oxygen sensor.
(b) Disassemble four bolts, compressed spring and front ex-
haust pipe with Three-Way Catalytic Converter assembly.
7. Disassemble heat insulation board of front exhaust
pipe.
Disassemble there screw caps and heat insulation board of
front exhaust pipe.
8. Disassemble parking front brake pull cable
assembly.
9. Assemble parking front brake pull cable assembly.
10. Assemble heat insulation board of front exhaust
pipe.
Assemble heat insulation board of front exhaust pipe with there
screw caps.
Torque: 5.4 N
⋅ ⋅⋅ ⋅
⋅m
11. Assemble front exhaust pipe with Three-Way Cata-
lytic Converter assembly.
(a) Assemble two new gaskets and front exhaust pipe with
Three-Way Catalytic Converter assembly with four com-
pressed springs and bolts.
Torque: 43
± ±± ±
± 3 N
⋅ ⋅⋅ ⋅
⋅m
(b) Connect the joint of oxygen sensor.

Parking rear brake pull cable assembly
Change
Hint: the changing procedure for left rear brake pull cable is same as parking right rear brake
pull cable.
1. Disassemble rear wheels.
2. Disassemble rear brake disk brake branch pump bracket assembly(LH).
3. Disassemble brake disk.
4. Disassemble support lever of parking brake shoe (LH).
5. Disassemble adjustor of parking brake shoe.
6. Disassemble parking brake inner shoe assembly (LH).
7. Disassemble parking brake exterior shoe assembly (LH).
8. Disassemble parking brake shoe lever (LH).
9. Disassemble left rear brake pull cable assembly.
Disassemble the bolt and parking left rear brake pull cable assembly from brake back board.
10. Disassemble front bottom board bracket.
11. Disassemble front part exhaust pipe.
12. Disassemble heat insulation board.
13. Disassemble parking left rear brake pull cable assembly.
Parking brake--Parking rear brake pull cable assembly
(a) Disassemble fixing clamp of rear wheel speed sensor wiring
harness.
(b) Disassemble four bolts and parking left rear brake pull cable
from automobile.
(c) Disassemble left rear brake pull cable from parking brake
balancer, then disassemble parking left rear brake pull cable.
14. Assemble parking left rear brake pull cable
assembly.
(a) Connect parking left rear brake pull cable on parking brake
pull cable balancer.
(b) Assemble parking left rear brake pull cable with four bolts.
Torque: 5.4 N
⋅ ⋅⋅ ⋅
⋅m
(c) Connect resinous clamp of speed sensor wiring harness of
 158 

Panel/combination instrument--combination instrument
Panel / combination instrument
combination instrument
Trouble table
Lightening:
Phenomenon
All lights fail
Only one light failsPossible parts of trouble
1. combination instrument assembly
2. joint or harness
1. combination instrument assemblyReference pages
-
-
-
Indicator light:
Phenomenon
Trouble light fails
Charge light fails
Brake system light fails
ABS light fails
SRS lights fails
Door light fails
low fuel level light fails
low Oil pressure light failsPossible parts of trouble
1. harness or joint
2. engine ECU
3. combination instrument assembly
1. harness or joint
2. engine ECU
3. combination instrument assembly
1. harness or joint
2. ABS ECU
3. combination instrument assembly
1. harness or joint
2. ABS ECU
3. combination instrument assembly
1. harness or joint
2. airbag sensor assembly
3. combination instrument assembly
1. harness or joint
2. door control switch
3. combination instrument assembly
1. harness or joint
2. fuel level light switch
3. combination instrument assembly
1. combination instrument assembly
2. oil pressure light switch
3. harness or jointReference pages
-
-
-
-
-
-
-
-
335
-
-
335
-
-
-
-
-
-
-
335
335
-
335
335
 334