2008 Citroen C4 PICASSO DAG Owner's Manual

A
BCD
142
III
Replacing a cartridgeThe recharge for the air freshener consists of a car-tridge B and its sealed container C.1. Remove the protective fi lm D.
2. Place the head of the cartridge B on the button A of the air freshener.
3. Rotate it a quarter turn to lock it on the button and remove the container.
4. Insert the air freshener into its housing.
You can change cartridges at any time, keeping the used cartridges in their original containers.
For safety, use only cartridges that are provided for this purpose.
Do not attempt to take cartridges apart.
Never recharge the cartridges with fragrances not supplied by CITR OËN.
Keep them out of reach of children and animals.
Avoid all contact with the skin and with the eyes.
In the event of swallowing, consult a doctor and show him the product packaging or label.
Do not install or remove a cartridge while you are driving.
Air freshener button
The air freshenerbutton A is independent of the car-tridge. Cartridges are supplied without the air fresh-ener button A.
The button of the air freshener Afreshener can only be fi xed into the central dashboard with a cartridge attached.
Therefore always keep the air freshener button A and one cartridge.
Note : Recharges are available, depending on country, either on the CITROËN Internet site or from a CITROËN deal er. Recharges are available, depending on country, either Recharges are available, depending on country, either
Stowage points are provided in the glovebox for sto ring of cartridges and containers.
S C E N T E D A I R F R E S H E N E R C H A N G I N G T H E C A R T R I D G E

12
3
3
2
4
III
143
To open the tailgate
- Press on the control 1.
Note : You cannot open the tailgate if the rear screen is already open.
To close the tailgate
- Lower the tailgate, using one of the handholds 3, located on the inside of the tailgate trim.
- Past the balancing point, allow the tailgate to close itself (do not assist it or slow it down).
To open the rear screen
Your vehicle may have an opening rear screen.
This opening confi guration gives you enhanced access to the boot-space, even if you are parked close to a wall or to another ve-hicle.
- Press on the control 2.
To close the rear screen
- Lower the rear screen.
Note :
- The handhold 4 is in line with the rear wiper.
- In the C4 Picasso vehicle, if the rear screen is open, you can ac-cess your bootspace by lifting the rear shelf using the tab located on the shelf.
O P E N I N G T H E B O O T

144
III
B O O T L U G G A G E C O V E R - C 4 P I C A S S O
LUGGAGE COVER IN TWO SECTIONS
Rear shelf
To remove
1. Unhook the cords.
2. Push upwards then lift on each side of the luggage cover.
To refi t
1. Present the luggage cover to its slots and push fi rmly down.
2. So that the luggage cover will rise with the tailgate, take the cords and attach them on the tailgate.
Front shelf
To remove
1. First remove the rear shelf.
2. Push upwards then lift on each side.
To refi t
1. Orient the fl ap downwards.
2. Present the luggage cover to its slots and push fi rmly down.

III
145
MODUBOX
The Modubox is for use both inside the vehicle and away from the vehicle. It is composed of a shopping trolley and a fl exible bag (isotherm on some versions) which can be used independently of each other de-pending on your needs (by detaching the fastenings on each side at the top and bottom).
To use
1. Unhook the red strap to free the Modubox.
2. Unhook the black strap then press on the round buttons on either side of the Modubox simultaneously to deploy it.
B O O T M O D U B O X - C 4 P I C A S S O
Use of the Modubox outside the vehicle
- Press on the recess on the left hand side of the Modubox to raise (or lower) the handle.
Stowage inside the vehicle
- Perform the operations in reverse to fold and stow inside the vehicle.
- If you have used your Modubox away from the vehicle, take care to reposition it correctly in the housings pro-vided for this purpose.

12
78
3
56
4
78
12
3
56
4
146
III
B O O T C A R G O N E T - G R A N D C 4 P I C A S S O A N D C 4 P I C A S S O
Cargo net : Grand C4 Picasso
There are 8 anchoring rings in the boot to enable you to secure your loads :
- 1 and 2 underneath the luggage-cover blind.
- 3, 4, 7 and 8 on the boot fl oor.
- 5 and 6 on the boot pillars.
Cargo net : C4 Picasso
There are 8 anchoring rings in the boot to enable you to secure your loads :
- 1, 2, 3 and 4 on the boot fl oor,
- 5, 6, 7 and 8 on the boot pillars.
The cargo net gives you a number of confi gurations depending on which of the anchoring rings you attac h it to (hammock format, vertical / horizontal, on the fl oor or behind the second row seats), enabling you to secure a variety of objects in the boot.
Note : For reasons of safety in the event of sudden braking, it is re commended that you place heavy objects on the fl oor as close as possible to the backrests of the second-row se ats.
Carrier bag hook
A carrier bag hook is available inside the boot on the left hand side.

CD
AAB
III
147
B O O TL U G G A G E C O V E R B L I N D - G R A N D C 4 P I C A S S O
Luggage-cover blind
Position 1 : (5-seat confi guration, behind the second row)
Behind the second-row seats, with the third-row seats folded away.
To install the roller :
1. Position the left-hand end of the blind roller in notch A.
2. Compress the right-hand end of the roller and place it in notch B.
3. Unroll the blind until it reaches the boot pillars.
4. Insert the guides of the blind into the rails on the pillars.
To remove the blind:
- Perform these operations in reverse order.
Note : the rollerhas a moving fl ap to avoid interference with the second-row passengers when the seats are i n the reclined position.
Position 2 : (7-seat confi guration)
Behind the third-row seats, this position conceals objects stowed in the boot from outside view.
To install the roller :
1. Roll up the blind, then remove the roller from its initial position.
2. Position the roller, with the blind pull bar upper-most, fl ap downward.
3. Fold the concertina plates in the vertical position.
4. Engage the lug on the left of the roller in notch C.
5. Pass the right-hand side above the third-row arm-rest.
6. Engage the lug in notch D.
7. Pull the seat belt(s) so that they will deploy without locking.
8. Unroll the blind and engage the guides into the rails on the pillars.
9. Lock the seat(s) in position.
10. Fold back the concertina plates, pressing them fi rmly in position.

CD
148
III
B O O TL U G G A G E C O V E R B L I N D - G R A N D C 4 P I C A S S O
Position 2 : (continued)
To remove the roller :
1. Push the fl ap towards the seat backrest.
2. Lift the concertina plate by grabbing it at the side, then position it vertically.
3.Unlock the seat by pulling the strap G (see “Third-row rear seats”).
4. Push the backrest towards the front.
5. Proceed in reverse order to installing.
Note : you can position the concertina plate vertically to lodge a bulkier object in the boot well.
Position 3 : (7-seat confi guration, stowage position)
To install the roller :
1. Remove the blind from its current position.
2. Position the roller, with the blind pull bar uppermost, fl ap downward.
3. Engage the lug on the left of the roller in notch C.
4. Pass the right-hand side above the third-row armrest.
5. Engage the lug in notch D.
To remove the roller :
- Proceed in reverse order to installing.

III
149
B O O TH I G H C A R G O N E T - G R A N D C 4 P I C A S S O
High cargo net
This enables you to maximise the vehicle’s load-space.
It retains objects, preventing them from sliding towards the front of the passenger compartment.
You insert it under the roller of the luggage-cover blind, securing it on the third-row side mouldings.
Position 1 (5-seat confi guration, behind the second row)
To install the roller :
1. Remove the protection covers located under the blind roller notches.
2. Position the roller under that of the luggage-cover blind.
3. Raise the fl ap on the blind, positioning it on top of the blind.
4. Deploy the net, passing it between the rollers and the seats.
5. Pull the net upwards.
6. Anchor it to the roof by means of the fi xing points (after you have removed their covers).
To remove :
- Perform these operations in reverse order.
Position 2 (2-seat confi guration, behind the fi rst row)
To install the roller :
1. With the second-row seats folded away, remove the covers of the Isofi x anchoring points located on the seat backrests.
2. Secure the roller on the Isofi x anchoring points.
3. Deploy the net and pull it upwards.
4. Anchor it to the roof by means of the fi xing points (after you have removed their covers).