2008 Citroen C CROSSER DAG Owner's Manual

C O M F O R T
II
52
Rear armrest
Lower the armrest to use it.
To return to the initial confi guration,
push the armrest until it locks in its ver-
tical position. Access to the third row
The passenger gains access to the
third row of seats by tilting a second
row seat.
To put this seat back in place, refer to
the following pages.

C O M F O R T
II
53
Folding the second row

1. Raise the rear seat lever A , or
Pull the button in the boot B for at least one second, or
Pull the rear seat releasing strap C towards you.

2. The seat backs fold forwards then the cushion rises and folds fo rwards.

3. After carrying out these operations, press on the seat lightly to check that it is secured correctly.
Before folding the seats, lower the head restraints fully.
Before folding the seat backs forwards, insert the seat belt b
uckles in the slots provided for this purpose in the rear seat
cushion.

Before folding the seats , ensure that no object or person is hindering the execution of the operatio ns.
Do not place luggage on the folded seats.

C O M F O R T
II
54
Returning the second row to the normal position

1. Lower the seat pulling simultane-
ously on the releasing strap
A lo-
cated at the rear of the cushion and
supporting the seat with your hand.
Force may be necessary to carry out these operations.
On vehicles fi tted with a third row, the rear of the cushio n of the second row is fi tted with a low light B .
When the releasing strap is pulled, the light comes on for approximately 10 seconds to light the fl oor at the base of t he
third row.
2. Press on the cushion to put it in
place until it engages.
3. Pull the seat back upright pulling si-
multaneously on the releasing strap
located at the rear of the seat back.

4. After putting the seat back back in
place, push the seat and the seat
back lightly to ensure that they are
secured correctly.

C O M F O R T
II
55
“Lowered seats” configuration

1. Remove the head restraints from the front seats.

2. Raise the rear armrest and remove the load space cover.

3. Move the rear seats as far back as possible.

4. Move the front seats as far forward as possible and tilt their s eat backs fully.

5. Tilt the seat back of the rear seats.
To return the seats to their normal position, carry out these o perations in reverse order.

C O M F O R T
II
56
REAR BENCH SEAT (ROW 3)
The rear bench seat can be folded. It
retracts into a location in the fl oor of the
vehicle. The label on the bench seat back illus-
trates the various steps to be followed
when unfolding and folding the rear
bench seat.
1. Open the tailgate and the lower tail-
gate (refer to the “Access section”).

2. Pull the cover A from the rear and
fi x it to the seat back using the press
stud of the band B .
Unfolding the bench seat
For comfort, it is advisable to fold the
bench seat when its is not is use.

C O M F O R T
II
57

3. Pull the black strap
C located at the
centre of the seat back to raise the
seat back.
4. Pull the black strap
D to release the
bench seat cushion.
5. Tilt the bench seat rearwards.

6. Raise the head restraints. 7. Lift and push the bench seat assem-
bly forwards until it locks.
Undo the press stud of band B to re-
lease the cover.

C O M F O R T
II
58

1. Open the tailgate and the lower tail-
gate (refer to the “Access” section).

2. Lift the cover A and fi x it to the seat
back using the press stud of the
band
B .
3. Unlock the head restraints by sliding
the controls
C and fold them onto
the seat back.
4. Pull the grey strap
D and bring the
bench seat towards you. Press on
the bench seat to lock it.

5. Tilt and push the bench seat for-
wards.
6. Pull the black strap E located at the
centre of the seat back to fold the
seat back.
Undo the press stud of the band B to
put the cover back in place.
Folding the bench seat

C O M F O R T
II
59
EXTERIOR MIRRORS
Electric folding / unfolding
- from inside, with the ignition switch in the “ON” or “ACC” position

 by pressing the control C .
- from inside, with the ignition switch in the “LOCK” position:

 by pressing the control C, within
30 seconds.
- from outside using the remote control:

 by pressing the “closed padlock”
button briefl y 3 times to fold
them,

 by pressing the “open padlock”
button briefl y 3 times to unfold
them.
Adjustment
The mirrors can be adjusted when the
ignition switch is in the “ON” or “ACC”
position.

 Move control
A to the right or to
the left to select the corresponding
mirror.

 Direct control
B in all four direc-
tions to adjust the mirror.
When adjustment is complete, return
control A to the central position. If you switch the engine off then re-
start it with the mirrors folded, they
will unfold automatically when the
vehicle reaches 20 mph (30 km/h).
If the mirrors have been folded man-
ually or electrically after starting the
engine, they are not unfolded auto-
matically.
In this case:

 Press the control C to unfold
them. If you have folded the mirrors
using the control
C , you must
use this control to unfold them,
otherwise the mirrors will not be
locked correctly.

The folding and unfolding of the exte-
rior mirrors can be confi gured via the
colour display “Equipment” menu or
deactivated by a CITROËN dealer.
The mirrors can also be folded manually.