2008 Citroen C CROSSER DAG Owner's Manual

D R I V I N G
VII
113
Operating faults
If the selected transmission mode
display fl ashes, the vehicle switches
automatically to front “2WD”

transmission mode.
It is then no longer possible to select the
transmission mode using the control A . Do not subject the vehicle to
excessive conditions while driving.
As the engine torque is applied to
all four wheels, the condition of the
tyres has a considerable impact on
the performance of the vehicle.
Ensure that all four tyres are in good
condition.
Avoid driving the vehicle in sandy
or muddy areas or in other areas in
which the wheels could spin.
Spinning the wheels places the
transmission components under
pressure and could cause a serious
malfunction.
Do not drive the vehicle through
deep water.
Avoid driving over excessively
uneven terrain (risk of scraping
under the body or of grounding on
crossing a bridge).
Have your vehicle towed on
a fl atbed.
The vehicle must not be towed
with the front or rear wheels on the
ground even if it is in front “2WD”
(2 wheel drive) mode.
If the message “SLOW DOWN” is
displayed on the instrument panel, let
the transmission cool down then wait
for the display to clear before setting off
again.
If “4WD” and “LOCK” are displayed al-
ternately and if “MAINTENANCE RE-
QUIRED” is displayed on the instru-
ment panel, the system has failed and
the safety system has been activated.
Contact a CITROËN dealer without
delay.

D R I V I N G
VII
114
Programming

 Press button 1 .

 Set the programmed speed by ac-
celerating to the required speed,
then press button 2 “COAST
SET” .
CRUISE CONTROL
The controls of this system are grouped
together on the steering wheel.

1.
“ON/OFF” button: activation / deac-
tivation of the cruise control mode.

2.
“COAST SET” button: storing of a
driving speed and decreasing of the
cruising speed.

3.
“ACC RES” button: increasing of
the cruising speed and recalling of
the stored speed.

4.
“CANCEL” button: switching off of
the cruise control. When you press button
1 , “CRUISE”
indicator light comes on on the instru-
ment panel.
Steering wheel controls Display on the instrument pan
el
The cruise control cannot, in any cir-
cumstances, take the place of the
need to comply with speed limits or
of the vigilance and responsibility of
the driver.
System which permits automatic main-
taining of the vehicle speed at the value
programmed by the driver, without any
action on the accelerator pedal.

The
cruise control is switched on
manually: the vehicle speed must be
25 mph (40 km/h) minimum and sec-
ond gear must be engaged in the case
of a manual gearbox.

The cruise control is switched off
manually, by an action on the brake or
clutch pedal or if the ASC system is trig-
gered.

The programmed speed can be ex-
ceeded temporarily by pressing the ac-
celerator pedal.
To return to the programmed speed,
simply release the accelerator pedal.

Switching off the ignition cancels any
programmed speed value.

D R I V I N G
VII
115
When the cruise control is
in operation, pay attention if
you press and hold one of
the programmed speed adjustment
buttons: this can result in a very rapid
change in the speed of your vehicle.
Do not use the cruise control on
slippery roads or in heavy traffi c.
On a steep descent, the cruise control
will not be able to prevent the vehicle
from exceeding the programmed
speed.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly,
- never fi t one mat on top of another.
Deactivating the function
To deactivate the cruise control:

 Press the brake or
clutch pedal, or

 Press button 1 “ON OFF” , or

 Press button 4 “CANCEL” .

The cruise control may be deactivated
automatically:

 When the vehicle reaches a speed
below 20 mph (35 km/h).

 When the active stability control
system (ASC) comes into operation. Reactivating the function
When the cruise control has been
deactivated, you can return to the
stored speed by pressing button
3
“ACC RES” when you reach a mini-
mum speed of 25 mph (40 km/h).
Decreasing the programmed
speed

 Using button 2 “COAST SET” :
- successive presses decrease the speed in steps of approximately
1 mph (1.6 km/h).
- a maintained press of this button decreases the speed progressively.
Once the speed required has been
reached, release the button, the new
speed is stored.

 Using the brake pedal:
- brake to deactivate the cruise con- trol, then press button 2 “COAST
SET” . Release to store the new
speed. Temporary acceleration/
deceleration
Increasing the programmed
speed

 Using button 3 “ACC RES” :
- successive presses increase the speed in steps of approximately
1 mph (1.6 km/h).
- a maintained press of this button increases the programmed speed
progressively.
Once the speed required has been
reached, release the button, the new
speed is stored.

 Using the accelerator pedal:
- accelerate to reach the speed re- quired, then press button 2 “COAST
SET” . Release the button to store
the new speed. Temporary acceleration
Press the accelerator pedal as normal.
When the pedal is released, you return
to the stored speed.
Temporary deceleration
Press the brake pedal to reduce the
speed. To return to the stored speed,
press button
3 “ACC RES” .

D R I V I N G
VII
116
AUDIBLE REAR PARKING
ASSISTANCE
It detects any obstacle (person, vehicle,
tree, gate,...) located behind the vehicle,
but it cannot detect obstacles located
immediately below the bumper. Activation
The parking assistance is activated by
engaging reverse gear.
The proximity information is indicated
by an audible signal which becomes
more frequent as the vehicle approach-
es the obstacle.
When a certain distance between the
rear of the vehicle and the obstacle is
reached, the audible signal becomes
continuous:
An object such as a stake, a road
works cone or any other similar object
may be detected at the beginning of
the manoeuvre but may no longer
be detected when the vehicle moves
closer to it.
Location of the sensors
The vehicle is fi tted with four sensors:
- two side sensors
A
- two central sensors B . Vehicle only
Vehicle fi tted with a towbar
Detection zones
The detection zones differ according to
the vehicle’s equipment, with or without
towbar.
Therefore, you can select the towbar
mode, the fi tting zone
C is excluded
from the detection zones.
The parking assistance system
cannot, in any circumstances, take
the place of the need for vigilance
and responsibility on the part of the
driver.
Sensors

Distance between
vehicle and
obstacle less than:
Side A Approximately
25 cm
Central B without
towbar Approximately
40 cm
Central B with
towbar Approximately
60 cm
System consisting of proximity sensors,
installed in the rear bumper.

D R I V I N G
117
REVERSING CAMERA
Linked with the navigation option, a re-
versing camera is activated automati-
cally when reverse gear is engaged.
The colour visual return is provided on
the navigation display with indication of
the limit of the rear bumper and of the
general direction of the vehicle.
Operating fault
If an operating fault occurs, the indicator
light on button
A fl ashes when reverse
gear is engaged.
Consult a CITROËN dealer.
In bad weather or in winter, check
that the sensors are not covered with
mud, ice or snow.
Deactivation

 With reverse gear engaged, press
button A , the indicator light switches
off, the system is fully deactivated.
Reactivation

 With reverse gear engaged, press
button A again, the indicator light
comes on, the system is reactivated.
Modifi cation of the detection zones

 Press button A to deactivate the
system.

 Press button A again for a few sec-
onds and release it.
The detection zone modifi cation infor-
mation is indicated by an audible signal
which:
- is heard twice on vehicles fi tted with
a towbar,
- is heard once on vehicles which are
not fi tted with a towbar.
The red line indicates the distance
required to open the lower tailgate.

D R I V I N G
117
REVERSING CAMERA
Linked with the navigation option, a re-
versing camera is activated automati-
cally when reverse gear is engaged.
The colour visual return is provided on
the navigation display with indication of
the limit of the rear bumper and of the
general direction of the vehicle.
Operating fault
If an operating fault occurs, the indicator
light on button
A fl ashes when reverse
gear is engaged.
Consult a CITROËN dealer.
In bad weather or in winter, check
that the sensors are not covered with
mud, ice or snow.
Deactivation

 With reverse gear engaged, press
button A , the indicator light switches
off, the system is fully deactivated.
Reactivation

 With reverse gear engaged, press
button A again, the indicator light
comes on, the system is reactivated.
Modifi cation of the detection zones

 Press button A to deactivate the
system.

 Press button A again for a few sec-
onds and release it.
The detection zone modifi cation infor-
mation is indicated by an audible signal
which:
- is heard twice on vehicles fi tted with
a towbar,
- is heard once on vehicles which are
not fi tted with a towbar.
The red line indicates the distance
required to open the lower tailgate.

C H E C K S
VIII
118
Bonnet strut
OPENING THE BONNET
To close
Lower the bonnet and release it at the
end of its travel. Check that the bonnet
is properly locked.

From inside: pull the handle A , on the
left-hand side below the door, towards
you.

From outside: move the catch to the
left then raise the bonnet. Secure the strut in its housing to hold
the bonnet open.
Before closing the bonnet, replace the
strut in its clip.
RUNNING OUT OF FUEL
Protection system which also provides
access for checking the various levels
of the engine components.
If you run out of fuel, fi ll the tank and op-
erate the starter until the engine starts.
Several attempts must be made before
the engine re-starts.

C H E C K S
VIII
119
PETROL ENGINE

1. Wash-wipe and headlamp wash
reservoir.

2. Coolant reservoir.

3. Power steering fl uid reservoir.

4. Brake fl uid reservoir.

5. Fuse box.

6. Battery.
7. “CVT” gearbox gauge.

8. Radiator cap.
9. Dipstick.

10. Engine oil fi ller cap.

11. Air fi lter.
This allows you access to check the level of the various fl uids a
nd replace certain components.