2008 AUDI A4 AVANT spare wheel

___ w_ h_ a_t _ d_ o_ l_d _ o_ n_ o_w _ ? ______________________________________________ _
Storing the replaced wheel
- Place the replaced wheel inside the spare wheel well in
the luggage compartment.
- Tighten the knurled retaining screw clockwise to secure
the wheel in place.
- Disengage and lower the floor panel before you close the
luggage compartment lid again.
& WARNING
Loose items in the passenger compartment can cause serious
personal injury during hard braking or in an accident.
• Never store the spare wheel or jack and tools
in the passenger
compartment.
• Always store all jacking equipment, tools, and the spare wheel
in the luggage compartment.
• Tighten the knurled retaining screw for the spare wheel
securely.
[ i] Tips
Check the inflation pressure of the spare tire periodically to keep the
tire ready for use. •
Wheel change
Before changing a wheel
Follow these points for your own and your passenger's
safety when replacing a wheel.
After you experience a tire failure, pull the car well away
from moving traffic and try to reach
level ground before
you
stop ~& .
-All passengers should leave the car and move to a safe
location (for instance, behind the
guardrail) ~& .
-Apply the parking brake firmly ~& .
-Move selector lever to position P on an automatic trans-
mission; put manual transmission in
first gear~& .
-If you are towing a trailer: unhitch the trailer from your
vehicle.
- Take the
tool case and the spare tire ~ page 316 out of
the luggage compartment.
& WARNING
You or your passengers could be injured while changing a wheel if
you do not follow these safety precautions:
• If you have a flat tire, move a safe distance off the road. Turn off
the engine, turn the emergency flasher on and use other warning
devices to alert other motorists.
• Make sure that passengers wait
in a safe place away from the
vehicle and well away from the roadway and traffic.
• To help prevent the vehicle from moving suddenly and possibly
slipping off the jack, always fully set the parking brake and block
the wheel diagonally opposite the wheel being changed . When one
front wheel is lifted off the ground, placing the Automatic Trans-
~

What do I do now? 11111111
-----------------------------------
& WARNING (continued)
mission in "P" (Park), or engaging a gear in a manual transmission
will
not prevent the vehicle from moving.
• Before you change a wheel, be sure the ground is level and firm.
If necessary, use a sturdy board under the jack.
• After installing the spare wheel, make sure that you remount
the flat tire/wheel in its storage area properly and tighten the
knurled retaining screw securely . •
Changing a wheel
When you change a wheel, follow the sequence described
below step-by-step and exactly in that order.
1. Remove the decorative wheel cover*. For more details
see also
=> page 320, "Decorative wheel covers" or
=> page 320, "Wheels with cap -covered wheel bolts".
2. Loosen the wheel bolts => page 321.
3.
Locate the proper mounting point for the jack and align
the jack below that
point=> page 321.
4. Lift the car with the jack => page 321.
5.
Take the flat wheel off and then put the spare on
=> page 323.
6. Tighten all wheel bolts lightly.
7.
Lower the vehicle with the jack.
8. Use the wheel bolt wrench and
firmly tighten all wheel
bolts=> page 321.
9. Put the decorative wheel cover* back on.
LJ}. WARNING
Always read and head all WARNINGS and information :::::> & in
"Raising the vehicle" on
page 321 and :::::, page 324. •
After changing a wheel
A wheel change is not complete without the following
actions.
-Store and secure the replaced wheel in the spare wheel
well.
-Put the tool case and the jack back in place in the luggage
compartment.
-Check the tire pressure on the spare wheel immediately
after mounting it.
- As soon as possible, have the
tightening torques on all
wheel bolts checked with a torque wrench. The correct
tightening torque is
90 ft lb (120 Nml.
- Have the flat tire
replaced as soon as possible.
[ i] Tips
• If you notice while changing a tire that the wheel bolts are
corroded and difficult to turn, then they should be replaced before
you check the tightening torque.
• Drive at reduced speed until you have the tightening torques
checked .•
Do -it -yourself service

What do I do now? -
------------------'
Taking the wheel off /putting the spare on
Follow these instructions step-by-step for changing the
wheel
Fig . 230 Wheel
change : using the
screwdriver handle
(with the blade
removed) to turn the
bolts
Fig . 231 Wheel
change : alignment pin
inside the top hole
After you have loosened all wheel bolts and jacked the
vehicle off the ground, perform the following steps to
remove and replace the wheel:
Removing the wheel
-Use the hexagonal socket in the screwdriver handle to
completely turn out the topmost wheel bolt and set it
aside on a
clean surface => fig. 230.
-Screw the threaded end of the alignment pin from the
tool kit hand -tight into the now vacant bolt hole
=> fig. 231 .
-Then completely unscrew the other wheel bolts as
described above.
-Take off the wheel leaving the alignment pin in t he bolt
hole.
Putting on the spare
-Lift the spare wheel up and carefully slide it over the
alignment pin to guide it in place.
-Use the hexagonal socket in the screwdriver handle to
screw in and t ighten all wheel bolts
slightly .
-Unscrew the alignment pin and insert and tighten the
remaining wheel bo lt slightly like the rest.
-Turn the handle on the jack counter-clockwise to lower
the vehicle until the jack is fully released.
-Use the wheel bolt wrench to tighten all wheel bolts
firmly =>
page 327. Tighten crosswise, from one bolt to
the (approximately) opposite one, to keep the wheel
centered.
[ i] Tips
Never try and use the h exagonal socket in the handle of the screw -
driver to loosen or tighten the wheel bolts.
.,
Do-it-yourse lf service irechnical data

____ w_ h_ a_t _ d_ o_ l_d _ o_ n_ o_w _ ? ______________________________________________ _
• Pull the reversible b lade from the screwdriver before you use the
h exago nal soc ket i n the ha ndle to tur n the wheel bo lts.
• When mounting tires with
unidirectional tread design make sure
th e trea d pat tern is po inte d the rig ht
way => page 324.
• T he whee l bo lts should be clean and easy to turn. Check for dirt
and c orrosio n on the m ating su rfaces of bo th the whee l a nd th e
hub . Remove a ll dirt from these surfaces before remou nting the
w heel. •
Tires with unidirectional tread design
T ir es wit h unid irectio nal tr ea d d esign must b e moun ted
with th eir tread pattern po int ed the r ight direction .
Using a spare tire with a tread pattern intended for use
in a specific direction
Whe n usi ng a s pa re t ire wi th a tre ad patte rn inte nd ed for use in a
specific direct ion, please note the followin g:
• The di rec tio n of rot ation is marked by an arr ow on th e s ide o f the
tir e.
• If the s pare tir e ha s to be ins talle d in th e inco rrect directi on i n the
event of a flat tire, use th e spar e tire on ly temporarily since the tire
w ill n ot be a ble to achieve it s optimum pe rform ance cha rac te ri sti cs
wi th r egar d to a qua plani ng , noise an d w ear .
• W e rec om mend th at p arti cula r att ent ion be pai d to this fac t
dur in g wet weath er and that you adjust your sp eed to match road
c o nd it io ns.
• R eplace the flat ti re with a new one and have it instal led on your
v e hi cle as soo n as poss ib le to re st ore th e hand ling a dva ntages of a
p roper ly pointed direction -dependent t ire.•
Notes on wheel change
P lease read the information => page 305 , "N ew tire s and replacing
t ir es a nd whe els" if you are going to use a spa re tire w hich is
different from the t ires on you r ve h ic le.
Aft er you ch ange a tire:
• Check the tire pressure on the spare immediately after
mounting .
• Have the wheel bolt tightening torque checked with a torque
wrench as soon as possible by your authorized Audi dealer or a qualified service station .
• On steel and alloy wheel rims , the wheel bolts are correctly tight­
ened with a torque of 90 ft lb (120 Nm ).
• If you notice while changing a tire that the wheel bolts are
corroded and difficult to turn while changing a tire , they should be
replaced before you check the tightening torque.
• Replace the flat tire with a new one and have it installed on your
vehicle as soon as possible . Remount the wheel cover.
Until then, drive with extra care and at reduced speeds .
& WARNING
• If you are going to equip your vehi cle with tires or rims which
differ from those which were factory installed , then be sure to read
the information
=> page 305 , "New tires and replacing tires and
wheels ".
• Always make sure the damaged wheel or even a flat tire and
the jack and tool kit are properly secured in the luggage compart­
ment and are not loose in the passenger compartment .
• In an accident or sudden maneuver they could fly forward ,
injuring anyone in the vehicle .
• Always store damaged wheel, jack and tools securely in
luggage compartment . Otherwise, in an accident or sudden

ffl,...__G_ e_ n_ e_r_a _ l_ i
_ n_ f_ o_ rm_ a
_ t_io _ n _______________________________________________ _
General information
Explanation of technical data
Some of the technical data listed in this manual require
further explanation.
The technical da ta for your vehicle are listed in the charts starting
on => page 343. This chapter p rovides general information, notes
and restrictions which apply to these data. •
Vehicle identification
The key data ore given on the vehicle identification
number (VIN) plate and the vehicle data sticker.
Fig . 241 Vehicle Identi­
fication Number (VIN)
plate: location on
driver's side dash
panel Fig
. 242 The vehicle
identification label
-
inside the luggage
compartment
The Vehicle Identification Number (VIN}
is located on the driver's side so that it is visible from the outside
through the windshield -
see:::::, fig. 241.
The vehicle identification label
is located in the luggage compartment in the spare wheel well.
The
label => fig. 242 shows the following vehicle data:
G) Production control no.
0 Vehicle identification no .
© Type code number
© Type designation/engine output in Kilowatts
© Engine and transmission code letter
© Pain t no./lnt erior
0 Optional equipment no.'s
Vehicle data 2 to 7 are also found in your Maintenance
& Warranty
booklet .
..,.

llffl _ __::C:::.::: o:.:.n.:.: s:::.::: u:.:.m .:.:.: e:.: r~ I n:..:.:. f.::
o :.:.r .:.m :.:.:: a:.: t:.:. i.::o :.:.n.:.... _____________________________________________ _
&, W ARNING (continued )
• Always support your vehicle with safety stands if it i s neces­
sary to work underneath the vehicle. The jack supplied with the
vehicle is not adequate for this purpose and could collapse
causing serious personal injury .
• If you must work underneath the vehicle with the wheels on
the ground , always make sure the vehicle is on level ground , that
the wheels are always securely blocked and that the engine
cannot be started .
• Always make sure the transmission selector lever (automatic
transmission) is in
" P " (Park position) and the park brake is firmly
applied.
ffi For the sake of the environment
• Changing the engine settings wi ll adverse ly affect emission
l eve ls . T hi s is detri menta l to th e envi ro nm ent and increas es fu el
consumption .
• Always observ e env ironmenta l re gulations w hen disposing of
old e ngine oil, used brake f luid, dirty engine coo lant, spent batteries
or worn out tires .•
Additional accessories,
modifications and parts replacement
Additional accessories and parts
replacement
Alway s co nsult an autho rized Audi de aler before
pu rchasing acc essories .
Your vehicle incorporates t he latest safety d esig n f eatures ensuring
a high standa rd of active and pas sive safety . Th
is saf ety could be compromised by non -approved changes to the
v ehi cle . F or thi s re aso n, if par ts have to be re pla ced , pl ease obs erve
th e fo llow ing points when insta lling add itional acc essories :
A pproved Aud i accesso ries and gen uine Audi pa rts a re avai la bl e
fr om authori zed Aud i dea lers .
Th ese dealers also have the necessary faci lities, tools and tra ined
spec ia li sts to in sta ll th e parts an d acce ssor ies pr op erly .
& WARNING
Using the wrong spare parts or using non -approved accessories
can cause serious personal injury .
• Use only accessories expressly approved by Audi and genuine
Audi spare parts .
• These parts and accessories have been specially designed to
be used on your vehicle .
• Never install accessories such as telephone cradles or
beverage holders on airbag covers or within the airbag deploy­
ment zones . Doing so will increase the risk of injury if airbags are
triggered in an accident!
• Before you check anything in the engine compartment , always
read and heed all WARNINGS
=> page 265.
0 Note
• I f item s ot her than ge nuin e Audi s pa re pa rts, add- on eq uipment
and accessory items are us ed or if r epair wor k is not performed
according to s pecified methods, thi s can re sult in severe damage to
your v ehicle's eng ine and body (suc h as c orros io n) a nd advers ely
affect yo ur vehic le 's wa rranty.
• Th e manufacturer cannot be held liable for damage w hich occurs
d ue t o fa ilur e to comply w it h these stipu lation s.•

___ A_l-=- p _h_ a_ b_e _t_ic _ a_l _in _ d_e _x ____________________________________________ _
Servotronic ........ .... .... ........ 241
Set menu ........................... 43
Setting Date display . . . . . . . . . . . . . . . . . . . . . . 14
Digital clock . .... .... .... .... .... . 14
Shift buttons . . . . . . . . . . . . . . . . . . . 148, 155
Side airbags Description . ...... .... ...... .... 203
How they work . . . . . . . . . . . . . . . . . . . 205
Side curtain a irbags
Description . ...... .... .... ... ... 207
How they work . . . . . . . . . . . . . . . . . . . 208
Safety instructions . . . . . . . . . . . . . . . 208
Side curtain airbags (SIDEGUARD) ... .. 207
Ski sack ....... .. .... .... ...... .... 114
Snow cha ins . . . . . . . . . . . . . . . . . . . . . . . 311
Sockets . . . . . . . . . . . . . . . . . . . . . . . 120, 121
Sound system Rep lacing ....................... 349
Sound system disp lay
Driver information display .......... 25 Steering
........ .... ... .. ...... .... 134 Tether strap ........ .... .... ... .. ... 230
Lo cking the steering .... .... .... .. 135 Securing the upper tether strap . ... 231
Steering wheel co lumn The first 1,000 miles (1,500 km) and
Adjusting ........ ... .. .... .... .. 134 afterwards ..................... 243
Steps for determining correct load limit 302 Tie -down strap .... .... ... .... .... .. 109
Stopping the engine .. ... .... ... .. ... 137 Tie-downs ..................... 108, 175
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 Ti lt sensors .. ... .... .... ....... .... . 65
Compartments in the door trims .... 124 Tips for the environment
Cup holder in the center console . .. 118 Saving fuel ... .... .... ........... 117
Cup holder rear center armrest ..... 118 tiptronic® .... ....... .... ........ .. 143
Glove compartment .............. 122
Automatic Sh ift Lock (ASU ....... .. 145
Luggage compartment ............ 114
Driving . . . . . . . . . . . . . . . . . . . . . . . . . 143
Owner's literature . ............... 123
Dynamic shift program ........ .... 146
Ski sack . . . . . . . . . . . . . . . . . . . . . . . . . 114
Fail-safe mode ................... 149
Small objects .. ............. ..... 123
Kick-down ... .. .... .... .... .... .. 146
Sun blind .. ...... ...... .... ... .. .... 84 Manual shift program ...... .... ... 147
Sun visors ...... .... ... .. .... .... ... 84 Selector
lever ....... ... .... .... .. 144
Switches Tire pressure
...... ................. 299
E mergency flasher .............. .. 79 Tire pressure monitoring system ...... . 46
Power sunroof .................... 67 Initialize wheels .... .... ...... ..... 50
Rear window defogger . . . . . . . . . . . . 131 Learning process ... .... .... .... ... 48
Spare wheel . . . . . . . . . . . . . . . . . . . . . . . 317
T
Speed rating letter code ...... .... ... 306 Loss of air pressure .
.... ... .... . 20, 47
Ma lfunctions ........ .... ... .. .... 51
Speed warning 1 ..................... 34 Tachomete r ......................... 13
Speed warning 2 ... .... ... .... .... ... 34
Speed warn ing system .. ...... ...... . 35
Speedometer . . . . . . . . . . . . . . . . . . . . . . . 15
Starting the engine . ...... ...... 135, 136
What should I do if the engine does not
start? . . . . . . . . . . . . . . . . . . . . . . . . . 136
Steel wheels .. ............... ... ... 259 Tailgate
S
ee Rear lid ....... .... .... ....... 61
Technical modifications ... ...... ... .. 349
Temperature Climate controls ................. 127
Setting for the driver 's and front passen­
ger's side . . . . . . . . . . . . . . . . . . . . . . 127 Sensors .
. . . . . . . . . . . . . . . . . . . . . . . . 307
Storing tire pressures .............. 48
Tires and wheels .. ....... .. .... .. 307
Valves ...... ...... .... ...... .... 307
Tire service life .... .... ............. 303
Tir es .... ... .. .... .... ......... .... 293
Replacing . .... .... .... .... .... .. 307
Service life .... .... ...... .... .... 303
speed rating letter code .... .... ... 306
Ti re manufacturing date ...... .... . 306