2007 YAMAHA YBR250 low beam

3-2
3
INSTRUMENT AND CONTROL FUNCTIONS
EAU11003
Indicator and warning lights1. Turn signal indicator light “
/
”
2. Neutral indicator light “N”
3. High beam indicator light “”
4. Fuel level warning light “
”
5. Engine trouble warning light “
”
EAU11030
Turn signal indicator lights
“
” and “
”
The corresponding indicator light flashes
when the turn signal switch is pushed
to the left or right.
EAU11060
Neutral indicator light “N”
This indicator light comes on when the
transmission is in the neutral position.
EAU11080
High beam indicator light “
”
This indicator light comes on when the
high beam of the headlight is switched
on.EAU11350
Fuel level warning light “
”
This warning light comes on when the
fuel level drops below approximately
4.5 L (1.19 US gal) (1.00 Imp. gal). When
this occurs, refuel as soon as possible.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical
circuit.
EAU11470
Engine trouble warning light “
”
This warning light comes on or flashes
when an electrical circuit monitoring the
engine is defective. When this occurs,
have a Yamaha dealer check the self-
diagnosis system.
EAU11601
Speedometer1. Speedometer
2. TachometerThe speedometer shows the riding
speed.
When the key is turned to “ON”, the
speedometer needle will sweep once
across the speed range and then return
to zero in order to test the electrical
circuit.
cap 3.pmd 24/1/2007, 14:37
2

3-5
3
INSTRUMENT AND CONTROL FUNCTIONS
EAU12350
Pass switch “
”
Press this switch to flash the headlight.
EAU12400
Dimmer switch “
/
”
Set this switch to “
” for the high beam
and to “
” for the low beam.
EAU12460
Turn signal switch “
/
”
To signal a right-hand turn, push this
switch to “
”. To signal a left-hand turn,
push this switch to “
”. When released,
the switch returns to the center position.
To cancel the turn signal lights, push the
switch in after it has returned to the
center position.
EAU12500
Horn switch “
”
Press this switch to sound the horn.
EAU12660
Engine stop switch “
/
”
Set this switch to “
” before starting
the engine. Set this switch to “
” to stop
the engine in case of an emergency, such
as when the motorcycle overturns or
when the throttle cable is stuck.EAU12710
Start switch “
”
Push this switch to crank the engine with
the starter.
ECA10050
See page 5-1 for starting instructions
prior to starting the engine.
EAU12820
Clutch lever1. Clutch leverThe clutch lever is located at the left
handlebar grip. To disengage the clutch,
pull the lever toward the handlebar grip.
To engage the clutch, release the lever.
The lever should be pulled rapidly and
released slowly for smooth clutch
operation.
The clutch lever is equipped with a clutch
switch, which is part of the ignition circuit
cut-off system. (See page 3-12.)
cap 3.pmd 24/1/2007, 14:37
5

6-27
6
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23780
Replacing the headlight bulbThis model is equipped with a quartz
bulb headlight. If the headlight bulb burns
out, replace it as follows.1. Remove the headlight unit by removing the screws.
1
1. Screw2. Disconnect the headlight coupler,and then remove the bulb cover.
2
1
1. Headlight coupler
2. Bulb cover
3. Remove the headlight bulb holder
by turning it counterclockwise, and
then remove the defective bulb.1.Headlight bulb holder
EWA10790
Headlight bulbs get very hot.
Therefore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.4. Place a new headlight bulb intoposition, and then secure it with
the bulb holder.
ECA10660
Do not touch the glass part of the
headlight bulb to keep it free from oil,
otherwise the transparency of the
glass, the luminosity of the bulb, and
the bulb life will be adversely affected.
Thoroughly clean off any dirt and
fingerprints on the headlight bulb
using a cloth moistened with alcohol
or thinner.1. Do not touch the glass part of the bulb5. Install the headlight bulb cover, andthen connect the coupler.
6. Install the headlight unit by installing the screws
7. Have a Yamaha dealer adjust the headlight beam if necessary.
cap 6.pmd 24/1/2007, 14:38
27