6-20
6
PERIODIC MAINTENANCE AND MINOR REPAIRTightening torques:Locknut:
16 Nm (1.6 m.kgf, 12 ft.lbt)
Axle nut: 104 Nm (10.4 m.kgf, 77 ft.lbt)4. Adjust the brake pedal free play.
(See page 6-16.)
EWA10660
After adjusting the brake pedal free
play, check the operation of the brake
light.
EAU23022
Cleaning and lubricating the
drive chainThe drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrication
chart, otherwise it will quickly wear out,
especially when riding in dusty or wet
areas. Service the drive chain as follows.
ECA10581
The drive chain must be lubricated
after washing the motorcycle and
riding in the rain.1. Clean the drive chain with keroseneand a small soft brush.
ECA11120
To prevent damaging the O-rings, do
not clean the drive chain with steam
cleaners, high-pressure washers or
inappropriate solvents.2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive chain with a special O-ring chain
lubricant.
ECA11110
Do not use engine oil or any other
lubricants for the drive chain, as they
may contain substances that could
damage the O-rings.
cap 6.pmd
24/1/2007, 14:38
20
7-1MOTORCYCLE CARE AND STORAGE
7
EAU26001
CareWhile the open design of a motorcycle
reveals the attractiveness of the
technology, it also makes it more
vulnerable. Rust and corrosion can
develop even if high-quality components
are used. A rusty exhaust pipe may go
unnoticed on a car, however, it detracts
from the overall appearance of a
motorcycle. Frequent and proper care
does not only comply with the terms of
the warranty, but it will also keep your
motorcycle looking good, extend its life
and optimize its performance.
Before cleaning1. Cover the muffler outlet with a plastic bag after the engine has
cooled down.
2. Make sure that all caps and covers as well as all electrical couplers
and connectors, including the spark
plug cap, are tightly installed.
3. Remove extremely stubborn dirt, like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such
products onto seals, gaskets, sprockets, the drive chain and
wheel axles. Always rinse the dirt
and degreaser off with water.
Cleaning
ECA10770
l
l l
l
l
Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the
affected area any longer than
instructed. Also, thoroughly
rinse the area off with water,
immediately dry it, and then
apply a corrosion protection
spray.
l
l l
l
l
Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use only
a soft, clean cloth or sponge with
mild detergent and water to
clean plastic.
l
l l
l
l
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
l
l l
l
l
Do not use high-pressure
washers or steam-jet cleaners
since they cause water seepage
and deterioration in the
following areas: seals (of wheel
and swingarm bearings, fork
and brakes), electric
components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
l
l l
l
l
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the
windshield. Test the product on
a small hidden part of the
windshield to make sure that it
does not leave any marks. If the
windshield is scratched, use a
quality plastic polishing
compound after washing.
cap 7.pmd 24/1/2007, 14:38
1
