2007 YAMAHA YBR250 brake

6-30
6
PERIODIC MAINTENANCE AND MINOR REPAIRTightening torque:Wheel axle:
60 Nm (6.0 m.kgf, 44 ft.lbt)5. Tighten the front fork pinch bolt to
the specified torque.Tightening torque:Front fork pinch bolt: 55 Nm (5.5 m.kgf, 40ft.lbt)6. Push down hard on the handlebar
several times to check for proper
fork operation.
EAU25080
Rear wheel
EAU25430
To remove the rear wheel
EWA10820
l
l l
l
l
It is advisable to have a Yamaha
dealer service the wheel.
l
l l
l
l
Securely support the motorcycle
so that there is no danger of it
falling over.
1. Loosen the axle nut and the brake
torque rod nut at the brake shoe
plate.
2. Lift the rear wheel off the ground according to the procedure on page
6-29.
3. Disconnect the brake torque rod from the brake shoe plate by
removing the nut and the bolt.
3
2
4 5
1. Drive chain slack adjusting nut
2. Brake torque rod
3. Locknut
4. Brake pedal free play adjusting nut
5. Axle nut4. Remove the brake pedal free play
adjusting nut, and then disconnect
the brake rod at the brake camshaft
lever.
5. Loosen the locknut and the drive chain adjusting nut on both ends
of the swingarm.
6. Remove the axle nut, and then pull the wheel axle out.
cap 6.pmd 24/1/2007, 14:38
30

6-31
6
PERIODIC MAINTENANCE AND MINOR REPAIR
7. Push the wheel forward, and thenremove the drive chain from the
rear sprocket.The drive chain does not need to be
disassembled in order to remove and
install the wheel.8. Remove the wheel.
EAUW0170
To install the rear wheel1. Insert the wheel axle from the left- hand side, and then install the drive
chain onto the rear sprocket.
2. Install the axle nut.
3. Install the brake rod onto the brake camshaft lever, and then install the
brake pedal free play adjusting nut. 4. Connect the brake torque rod to the
brake shoe plate by installing the
bolt and the nut, and then tighten
the nut to the specified torque.
Tightening torque:Brake torque rod nut: 49 Nm (4.9 m.kgf, 36 ft.lbt)5. Adjust the drive chain slack. (See
page 6-19.)
6. Lower the rear wheel so that it is on the ground.
7. Tighten the axle nut to the specified torque.Tightening torque:Axle nut: 104 Nm (10.4 m.kgf, 77 ft.lbt)8. Adjust the brake pedal position and
free play. (See page 6-16)
EWA10660
After adjusting the brake pedal free
play, check the operation of the brake
light.
EAU25850
TroubleshootingAlthough Yamaha motorcycles receive
a thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition systems,
for example, can cause poor starting
and loss of power.
The following troubleshooting chart
represents a quick and easy procedure
for checking these vital systems
yourself. However, should your
motorcycle require any repair, take it to
a Yamaha dealer, whose skilled
technicians have the necessary tools,
experience, and know-how to service the
motorcycle properly.
Use only genuine Yamaha replacement
parts. Imitation parts may look like
Yamaha parts, but they are often inferior,
have a shorter service life and can lead
to expensive repair bills.
cap 6.pmd 24/1/2007, 14:38
31

7-1MOTORCYCLE CARE AND STORAGE
7
EAU26001
CareWhile the open design of a motorcycle
reveals the attractiveness of the
technology, it also makes it more
vulnerable. Rust and corrosion can
develop even if high-quality components
are used. A rusty exhaust pipe may go
unnoticed on a car, however, it detracts
from the overall appearance of a
motorcycle. Frequent and proper care
does not only comply with the terms of
the warranty, but it will also keep your
motorcycle looking good, extend its life
and optimize its performance.
Before cleaning1. Cover the muffler outlet with a plastic bag after the engine has
cooled down.
2. Make sure that all caps and covers as well as all electrical couplers
and connectors, including the spark
plug cap, are tightly installed.
3. Remove extremely stubborn dirt, like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such
products onto seals, gaskets, sprockets, the drive chain and
wheel axles. Always rinse the dirt
and degreaser off with water.
Cleaning
ECA10770
l
l l
l
l
Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the
affected area any longer than
instructed. Also, thoroughly
rinse the area off with water,
immediately dry it, and then
apply a corrosion protection
spray.
l
l l
l
l
Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use only
a soft, clean cloth or sponge with
mild detergent and water to
clean plastic.
l
l l
l
l
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
l
l l
l
l
Do not use high-pressure
washers or steam-jet cleaners
since they cause water seepage
and deterioration in the
following areas: seals (of wheel
and swingarm bearings, fork
and brakes), electric
components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
l
l l
l
l
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the
windshield. Test the product on
a small hidden part of the
windshield to make sure that it
does not leave any marks. If the
windshield is scratched, use a
quality plastic polishing
compound after washing.
cap 7.pmd 24/1/2007, 14:38
1

7-2
MOTORCYCLE CARE AND STORAGE
7
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge, and
then rinse thoroughly with clean water.
Use a toothbrush or bottlebrush for hard-
to-reach areas. Stubborn dirt and insects
will come off more easily if the area is
covered with a wet cloth for a few
minutes before cleaning.After riding in the rain, near the sea oron salt-sprayed roads
Since sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the rain,
near the sea or on salt-sprayed roads.Salt sprayed on roads in the winter may
remain well into spring.1. Clean the motorcycle with coldwater and a mild detergent, after
the engine has cooled down.
ECA10790
Do not use warm water since it
increases the corrosive action of the
salt.2. Apply a corrosion protection sprayon all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning 1. Dry the motorcycle with a chamois or an absorbing cloth.
2. Immediately dry the drive chain and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally
induced discoloring of stainless-
steel exhaust systems can be
removed through polishing.)
4. To prevent corrosion, it is recommended to apply a corrosion
protection spray on all metal,
including chrome- and nickel-
plated, surfaces. 5. Use spray oil as a universal cleaner
to remove any remaining dirt.
6. Touch up minor paint damage caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely before storing or covering it.
EWA11130
l
l l
l
l
Make sure that there is no oil or
wax on the brakes or tires.
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires with
warm water and a mild
detergent. Before riding at
higher speeds, test the
motorcycle’s braking
performance and cornering
behavior.
ECA10800
l
l l
l
l
Apply spray oil and wax
sparingly and make sure to wipe
off any excess.
l
l l
l
l
Never apply oil or wax to any
cap 7.pmd 24/1/2007, 14:38
2

8-2
SPECIFICATIONS
8
28/22 (1.273)
4th:
26/25 (1.040)
5th:
23/27 (0.852)
Chassis:Frame type:Double cradle
Caster angle: 26.50 º
Trail:
104.5 mm (4.11 in)Front tire:Type:Tubeless
Size:
100/80-17M/C (52S)
Manufacturer/model: PIRELLI/SPORT DEMONRear tire:Type:Tubeless
Size:
130/70-17M/C (62S)
Manufacturer/model:
PIRELLI/SPORT DEMONLoading:Maximum load:167 kg (368 b)
(Total weight of rider, passenger, cargo
and accessories)
Tire air pressure (measured on cold
tires):Loading condition:0-90 kg (0-198 lb)
Front:
225 kPa (33 psi) (2.25 kgf/cm
2)
Rear: 250 kPa (36 psi) (2.50 kgf/cm2)
Loading condition:
90-167 kg (198-368 lb)
Front:
225 kPa (33 psi) (2.25 kgf/cm2)
Rear: 250 kPa (36 psi) (2.50 kgf/cm2)
Front wheel:Wheel type:Cast wheel
Rim size:
17M/C x MT2.15Rear wheel:Wheel type:Cast wheel
Rim size:
17M/C x MT3.00Front brake:Type:Single disc brake
Operation: Right hand operation
Recommended fluid:
DOT 3 or 4
Rear brake:Type: Leading, trailing drum brake
Operation: Right foot operation
Recommended fluid:
DOT 3 or 4Front suspension:Type:Telescopic fork
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel: 120.0 mm (4.72 in)Rear suspension:Type:Swingarm (link suspension)
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
120.0 mm (4.72 in)Electrical system:Ignition system: Transistorized coil ignition (digital)
Charging system: AC magnetoBattery:Model: YTX77L-BS
Voltage, capacity:
12 V, 6.0 Ah
cap 8.pmd 24/1/2007, 14:38
2

8-3
SPECIFICATIONS
8
Headlight:Bulb type:Halogen bulbBulb voltage, wattage x quantityHeadlight: 12 V, 35 W/35.0 W x 1
Tail brake light: 12 V, 5.0 W/21.0 W x 1
Front turn signal light:
12 V, 10.0 W x 2
Rear turn signal light:
12 V, 10.0 W x 2
Position light: 12 V, 5.0 W
Meter lighting:
14 V, 2.0 W x 2
Neutral indicator light:
14 V, 1.4 W x 1
Turn signal indicator light: 14 V, 1.4 W x 2
High beam indicator light:
14 V, 1.4 W x 1
Engine trouble warning light:
LEDFuses:Main fuse:20.0 A
Headlight fuse: 10.0 A
Signaling system fuse:
10.0 A
Ignition and fuel injection fuse:
10.0 A Backup fuse:
10.0 A
Spare fuses:
10.0 A and 20.0 A
cap 8.pmd 24/1/2007, 14:38
3